Page 2
Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable.
Important safety information Important Safety Information You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our local Customer Care Department Installation • This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant Australian Standards.
Page 4
Important safety information • • • • • When using the hob for a long period of time, the ventilation should be improved, by opening a window or increasing the extractor speed. • • • • • Do not use this hob if it is in contact with water. Do not operate the hob with wet hands.
Contents Contents For the User Important Safety Information Description of the Hob Operation Maintenance and Cleaning Something Not Working? For the Installer Instructions for the Installer Important safety requirements Installation Electrical connections Adaptation to different types of gas Building In Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions:...
Operation Operation Hob Burners To light a burner: • push in the relevant control knob and turn it anticlockwise to maximum position; • upon ignition, keep the knob pushed down about 5 seconds 5 seconds 5 seconds 5 seconds. This will allow 5 seconds the "thermocouple"...
Manteinance and Cleaning Maintenance and Cleaning Before any maintenance or cleaning can DISCONNECT DISCONNECT be carried out, you must DISCONNECT DISCONNECT DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
Something Not Working? Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SOLUTION SYMPTOM Check that the unit is plugged in and the There is no spark when lighting "...
Instructions for the Installer Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: 860 mm. Depth: 500 mm. CUT OUT DIMENSIONS Width: 830 mm. Depth: 470 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240 V 50 Hz supply APPLIANCE GAS SUPPLY:...
Page 11
Instructions for the Installer TYPE TYPE NOZZLE NOMINAL GAS NOMINAL OF GAS OF BURNER MARKS CONSUMPTION PRESSURE 1/100 mm MJ/h Triple Crown 13.00 NATURAL Rapid (large) 11.00 Semi-rapid (medium) 6.80 1.00 Auxiliary (small) 3.80 Triple Crown 13.00 Rapid (large) 11.00 U-LPG Semi-rapid (medium) 6.30...
Important safety requirements Important safety requirements This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant Australian Standards. The hob should not be installed in a bed sitting room with a volume of less than 20 m .
Installation Installation Important This appliance must be installed by qualified personnel. The installer shall verify the satisfactory operation of the ignition system on all burners both individually and in combination. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored.
Page 14
Installation Connection Carry out the connection to the gas plant only by means of a rigid metallic pipe conforming to the regulations in force. This appliance is not suitable for connection with a hose assembly. The joint for the entry of gas into the appliance is threaded R 1/2" (male thread). Carry out the connection avoiding any type of stress on the appliance.
Electrical connections Electrical connections The appliance is designed to be connected to 230-240 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label);...
Adaptation to different types of gas Adaptation to different types of gas WARNING: Servicing shall only be carried out by authorised personnel. Substitution of the nozzles - Remove all pan supports, burner caps, rings and crowns; - With a tubular spanner no. 7 unscrew and remove (see diagram) the nozzles substituting them with those corresponding to the type of gas used...
Building In Building In Dimensions are given in mm. Building over a cupboard or drawer If the hob is to be installed above a cup- ON/OFF SWITCH board or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface.
Building In Fitting the hob to the worktop Before fitting the hob into the cut out, a sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below.
Page 19
AEG WARRANTY- AUSTRALIA AEG WARRANTY AUSTRALIA Nothing in this warranty, limits any rights you may have under the Trade Prac- tices Act or any other Commonwealth or State legislation. Such rights cannot be changed by the conditions in this warranty. Subject to the conditions below, this appliance is warranted by Andi-Co Aus- tralia Pty.
Page 20
AEG WARRANTY - AUSTRALIA 10 This warranty does not cover loss, damage or expense to this appliance caused directly or indirectly by power surges, electrical storm damage or incorrect power current. 11 The Company (and any company related to the Company) will not be liable for any special, incidental or consequential damages or for loss, damage or expense or for personal injury or loss or destruction of property arising directly or indi- rectly from the use or inability to use this appliance or any of its parts.
Page 21
AEG WARRANTY– NEW ZEALAND AEG APPLIANCE WARRANTY – NEW ZEALAND This appliance is warranted by Electrolux Home Products (NZ) Ltd (“the Com- pany”) from the date of purchase. The following terms and conditions apply: 1 The Company or its Authorised Service Centre will pay the cost of repairing or...
AEG WARRANTY– NEW ZEALAND 11 The Company (and any company related to the Company) will not be liable for any special incidental or consequential damages or for loss, damage or expense directly or indirectly arising from the use or inability to use this appliance, or for personal injury or loss or destruction of other property.