B-52 Instruction And User's Manual page 22

From Previous Page
10. BOOTH: Use to adjust the level of the BOOTH
outputs.
11. cUE VOLUME: Use to adjust volume of the head-
phones.
12. cUE MIxING: Use to control signal routing to the
headphones. Turn all the way to the right to route the
MASTER OUTPUT signal to the headphones. Turn all the
way to the left for the sound from the channels with acti-
vated CUE to be routed to the headphones. At the center
position, the signal level of the MASTER OUTPUT and
signal from the channels with active CUE will be even.
• NOTE: Master output signal routed to
headphones is tapped before MASTER FADER.
CUE signals from channels 1-4 are tapped
before channels' faders.
13. SPLIT/BLEND: Use to configure headphone section
routing.
---- PRESS the button to activate SPLIT mode and LED
will light. In the SPLIT mode, mono CUE signals from the
channels will route to the left ear and mono signal from
MASTER OUTPUT will be routed to the right ear.
---- RELEASE the button to activate BLEND mode and
the LED will turn off. In the BLEND mode both the stereo
signal from MASTER OUTPUT and the CUE signals
from the channels will route to both ear cups of the
headphones.
14. Fx LOOP: Press to turn FX LOOP on or off. Use to
route signal of the channel to external effects processor
connected on the rear panel. The button will illuminate
when channel's signal is routed to the external effects.
• NOTE: If the external effect processor is off or is
not connected on rear panel and supplied jumpers
are removed from SEND/RETURN connectors for
external processor, signal will mute when this
knob is activated, as the signal path is open. The
Prodigy unit is shipped with these jumpers in
place. Make sure to keep them and INSERT into
EXTERNAL EFFECTS SEND/RETURN connectors if
you don't use an external processor.
---- cUE BUTTON: Use to direct this channel's signal to
the headphones. The button will illuminate when the
channel's signal is routed to the headphones.
15. MASTER FADER: Use to control the master output
sound level.
• TIP: Signals from the channels selected with the
ASSIGN switch will output proportionally to the
22
B-52 Professional Prodig y - Instruction Manual
PreCision for your PAssion
positions of both the channel fader and crossfader.
Signals from all other channels will output
proportionally to the positions of their channel
faders only.
16. INPUT FADERS (channel Faders): Adjusts the
volume for CH1 to CH4.
17. x-FADER ASSIGN: Use to select which channels are
assigned to A and B positions of the crossfader.
---- 1 to 4: Select the channel (CH1 to CH4) assigned
to A and B. Channels not assigned to A or B will be
directed to the output without passing through the
crossfader.
---- OFF: Select to disengage the crossfader.
• TIP: Use HAMSTER switch to instantly reverse
connection of the crossfader to A and B.
18. cROSS FADER (x-fader): Use to mix sound of
the sources set to A or B by the ASSIGN switch to the
MASTER OUTPUT.
• NOTE: Your Prodigy is equipped with high quality
X-fader and channel and master faders for great
performance and long service life. The X-fader and
channel faders control sophisticated VCA-based
circuitry for consistent and precise operation.
19. FADER START: Press to activate FADER START.
When FADER START knobs are pressed and lit, FADER
START mode is active. With both CD players playing
music, moving X-fader to the left will return right (op-
posite) CD player to the last set CUE point. If you didn't
set a CUE point, it will return to the starting point of the
current track. Moving X-fader to the right position will
do the same for the left CD player.
• NOTE: Setting CF SLOPE knob into the FCW
(full to the right) position will produce the most
effective results in FADER START mode.
• TIP: If your CD players are in a SINGLE play
mode and the FADER START mode is active and
one of CD players is paused, it will start
playing automatically when track on the other CD
player ends.
• TIP: You may also use the AUTO CUE SCRATCH
mode to activate fader start. To activate this mode
press and hold the SCRATCH button until it flashes
green. Touching the JOG WHEEL will act as a
fader start.
20. cF SLOPE: Use to adjust the "shape" of the X-fader
response from a gentle curve for smooth, long running