Table of Contents
Advertisement
Quick Links
APC-3x82/83
User Manual
Release Date
Revision
Jan 2013
V1.0
® 2013 Aplex Technology, Inc.
All Rights Reserved.
Published in Taiwan
Aplex Technology, Inc.
15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan
Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail:
aplex@aplex.com.tw
URL:
www.aplex.com.tw
APC-3x82/83 User Manual
1
Advertisement
Table of Contents
Related Manuals for Aplex APC-3x82
Summary of Contents for Aplex APC-3x82
-
Page 1: User Manual
APC-3x82/83 User Manual Release Date Revision Jan 2013 V1.0 ® 2013 Aplex Technology, Inc. All Rights Reserved. Published in Taiwan Aplex Technology, Inc. 15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw... -
Page 2: Warning
Disclaimer This information in this document is subject to change without notice. In no event shall Aplex Technology Inc. be liable for damages of any kind, whether incidental or consequential, arising from either the use or misuse of information in this document or in any related materials. -
Page 3: Packing List
Always disconnect power when the system is not in use. ◆ Disconnect power when you change any hardware devices. For instance, when you connect a jumper or install any cards, a surge of power may damage the electronic components or the whole system. APC-3x82/83 User Manual... -
Page 4: Table Of Contents
Warning!…………………………………………………………………………….……..….2 Disclaimer………………………………………………………………….…………………2 Packing List........................3 Safety Precautions......................3 Chapter 1 Getting Started 1.1 Specifications………………………………………….………….……...…..6 1.2 Dimensions…………………………………...……………….…………..8 1.3 Brief Description of APC-3X82/3X83.………………….………………12 Chapter 2 Hardware Installation 2.1 Mainboard Specifications………………………..…………….…………13 2.2 Jumpers Setting and Connectors………………………….……………17 Chapter 3 BIOS Setup 3.1 Operations after POST Screen.............26 3.2 BIOS SETUP UTILITY..............27... - Page 5 Figure 1.1: Dimensions of APC-3282/APC-3283……………………………...8 Figure 1.2: Dimensions of APC-3582/APC-3583..……………………...9 Figure 1.3: Dimensions of APC-3782/APC-3783……...………………..10 Figure 1.4: Dimensions of APC-3982/APC-3983…………...………………..11 Figure 1.5: Overview of APC-3X82 ……..…………………………...12 Figure 1.6: Overview of APC-3X83.........12 Figure 2.1: Mainboard Overview……………………………………..……..…13 Figure 2.2: Mainboard Dimensions……………………………………………13 Figure 2.3: Jumpers and Connectors Location-TOP…………………...……14 Figure 2.4: Jumpers and Connectors Location- Bottom………………….…14...
-
Page 6: Specifications
Luminance (cd/m2) View Angle H:160° / V:140° (APC-3582) H:130° / V:110° H:170° / V:160° H:160° / V:160° H:140° / V:110° (APC-3583) Backlight Lifetime 50,000 hrs Touch Screen Type Resistive Touch Light Transmission Power Supply Power Input DC 11~32V APC-3x82/83 User Manual... - Page 7 Mechanical Construction Stainless Steel Housing (APC-3X82) / Steel Housing (APC-3X83) IP Rating Front Panel IP65 / 6 sides IP42 with waterproof kit Mounting VESA 75x75 VESA 75x75 VESA 75x75 VESA 100x100 Mount Mount Mount Mount Dimensions (WxHxD) 335(W)x265(H) 399(W)x324(H)x 432(W)x358(H)x 470(W)x388.6(H)x...
-
Page 8: Dimensions
1.2 Dimensions Figure 1.1: Dimensions of APC3282/ APC-3283 APC-3x82/83 User Manual... -
Page 9: Figure 1.2: Dimensions Of Apc-3582/Apc-3583
Figure 1.2: Dimensions of APC-3582/APC-3583 APC-3x82/83 User Manual... -
Page 10: Figure 1.3: Dimensions Of Apc-3782/Apc-3783
Figure 1.3: Dimensions of APC-3782/APC-3783 APC-3x82/83 User Manual... -
Page 11: Figure 1.4: Dimensions Of Apc-3982/Apc-3983
Figure 1.4: Dimensions of APC-3982/APC-3983 APC-3x82/83 User Manual... -
Page 12: Brief Description Of Apc-3X82/3X83
1.3 Brief Description of APC-3X82/3X83 The fanless APC-3X82/3X83 is Intel Atom D525 powered panel PC with a rich variety of functions and peripherals . APC-3X82/3X83 is designed for easy and simplified integration into various vehicle applications. It comes with a compact flash slot, 2.5-inch hard disk drive, DDR3 memory, audio jack, 2 Ethernet, DC input. -
Page 13: Mainboard Specifications
Chapter 2__________Hardware Installation 2.1 Mainboard Specifications Figure 2.1: Mainboard Overview Figure 2.2: Mainboard Dimensions APC-3x82/83 User Manual... -
Page 14: Figure 2.3: Jumpers And Connectors Location-Top
Jumpers and Connectors Location-TOP Figure 2.3: Jumpers and Connectors Location- Bottom Figure 2.4: APC-3x82/83 User Manual... - Page 15 1x PS2 keyboard/mouse by 1x6 box pin header /Mouse Expansion Bus 1x PC 104+ connector (PCI master 4, jumper for +3.3V & 5V select) 2x mini-PCI-express slot (1x full size, 1x half-size ) Power DC12V input Management 1 x 2-pin power input connector APC-3x82/83 User Manual...
- Page 16 1 x DB15 Port or 2x8 Pin Header Operating: -20℃–70℃ Temperature Storage: -40℃–85℃ Humidity 5% - 95%, non-condensing, operating Power 12V /1.6A (Intel D525 processor with 2GB DDR3 DRAM) Consumption 12V /1.3A (Intel N455 processor with 2GB DDR3 DRAM) EMI/EMS Meet CE/FCC class A APC-3x82/83 User Manual...
-
Page 17: Jumpers Setting And Connectors
10 of COM6 port. JP1 Pin# Function Close 1-2 COM6 Pin10=+5V (default) Close 2-3 COM6 Pin10=+12V (option) 5. JP2: (2.0mm Pitch 1X2 Pin Header), ATX Power and Power auto on setting jumper. Mode APC-3x82/83 User Manual... - Page 18 Pin9-10: BUZZER, They are used to connect an external buzzer. Note: When connecting LEDs and buzzer, pay special attention to the signal polarity. Make sure that the connector pins have a one-to-one correspondence with chassis wiring, or it may cause boot up failure. APC-3x82/83 User Manual...
- Page 19 Since COM3 and COM33 use the same address, they cannot work at the same time. 10. GPIO: (2.0mm Pitch 2x5 Pin Header),General-purpose input/output port, it provides a group of self-programming interfaces to customers for flexible use. Signal Name Pin# Pin# Signal Name GPIO20 GPIO60 APC-3x82/83 User Manual...
- Page 20 AUD_AGND AUD_AGND FRONT-OUT-R LINEIN_L AUD_AGND AUD_AGND FRONT-MIC_L FRONT-MIC_ 13. COM2-COM6: (2.0mm Pitch 2x5 Pin Header),COM2 COM3 COM4 COM5 COM6 Ports, up to 5 standard RS232 ports are provided. They can be used directly via COM cable connection. APC-3x82/83 User Manual...
- Page 21 PS/2 keyboard or mouse via a dedicated cable for direct used. Pin# Signal Name KBDATA MSDATA Ground KBCLK MSCLK USB1/2: (Double stack USB type A), Rear USB connector, it provides up to 4 APC-3x82/83 User Manual...
- Page 22 2x8 Pin cable to VGA Port, they can not work at the same time for VGA and VGA-PH. Signal Name Pin# Pin# Signal Name CRT_RED Ground CRT_GREEN Ground CRT_BLUE CRT_R_HSYN CRT_PU_DDC_DAT CRT_R_VSYN CRT_PU_DDC_CLK +12V Ground +12V Ground APC-3x82/83 User Manual...
- Page 23 For 18 bit LVDS output connector, Fully supported by Intel Atom D525 chipset, the interface features single channel 18-bit output. Model name of the interface connector is Hirose DF13-30DP-1.25V. Signal Name Pin# Pin# Signal Name LVDS1_VDD5 LVDS1_VDD5 Ground Ground APC-3x82/83 User Manual...
- Page 24 (2.5mm Pitch 1x4 box Pin Header), onboard 5V and 12V output connector is reserved to provide power for SATA devices. Pin# Signal Name +DC5V Ground Ground +DC12V Note: Output current of the connector must not be above 1A. APC-3x82/83 User Manual...
- Page 25 (SO-DIMM 204Pin socket), DDRIII memory socket, bottom of the board and supports 204Pin 1.5V DDRIII 800MHz FSB SO-DIMM memory module up to 2G. 34. MPCIE SCREW HOLES: one screw holes for fixed MPCIE assemble. APC-3x82/83 User Manual...
-
Page 26: Chapter 3 Bios Setup
Auto – detecting USB Mass Storage Devices .. 00 USB Mass storage devices found and configured. Checking NVRAM.. 0085 Press F11 to load default values and continue 0085 Press F11 key to enter Boot Menu during POST, as shown by the following figure. APC-3x82/83 User Manual... -
Page 27: Bios Setup Utility
Time. Processor Intel ® Atom™ CPU D525 @ 1.80GHz Speed :1800MHz ← Select Screen Count ↑↓ Select Item Charge Field System Memory Tab Select Field Size :2038MB General Help F10 Save and Exit System Time [00:00:10] APC-3x82/83 User Manual... -
Page 28: System Overview
Second : 0 to 59 System Date: Set the system date, the date format is: Note that the „Day‟ automatically changes when you set the date. Day: Month: 01 to 12 Date: 01 to 31 Year: 2010 to 2099 APC-3x82/83 User Manual... -
Page 29: Advanced Settings
► Super IO Configuration ► Hardware Health Configuration ← Select Screen ► ACPI Configuration ↑↓ Select Item ► AHCI Configuration Enter Charge Field ► ASF Configuration General Help ► MPS Configuration Save and Exit ► PCI Express Configuration APC-3x82/83 User Manual... - Page 30 : [Not Detected] Hard Disk Write Protect [Disabled] IDE Detect Time Out (Sec) [35] ATA(PI) 80Pin Cable Detection [Host & Device] V02.68 © Copyright 1985-2009 American Mega trends , Inc. ATA/IDE Configuration: [Enhanced] [Disabled] Configure SATA as: APC-3x82/83 User Manual...
- Page 31 Serial Port5 IRQ [IRQ10] F10 Save and Exit Serial Port6 Address [2E0] ESC Exit Serial Port6 IRQ [IRQ11] WatchDog Setting [Disable] V02.68 © Copyright 1985-2009 American Mega trends , Inc. Serial Port3 Type: COM3 Options: [RS232 Type] APC-3x82/83 User Manual...
- Page 32 Show you the current CPU Fan operating speed. CPUFAN Mode Setting: [Manual Mode] [Thermal Cruise Mode] [Speed Cruise Mode] [Smart Fan3 Mode] 3.4.5 ACPI Configuration Section for Advanced ACPI Configuration Options: [Advanced ACPI Configuration] [Chipset ACPI Configuration] 3.4.6 AHCI Configuration APC-3x82/83 User Manual...
- Page 33 MPS Revision [1.4] Revision ← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 Save and Exit ESC Exit V02.68 © Copyright 1985-2009 American Mega trends , Inc. Configure the Multi-Processor Table. MPS Revision: [1.4] APC-3x82/83 User Manual...
- Page 34 Set Maximum Payload of allow System BIOS select the value. Extended Tag Field: [Auto] [Disabled] [Enable] No Snoop: [Auto] [Disabled] [Enable] Maximum Read Request Size: [Auto] [128/256/512/1024/2048/4096 Bytes] Set Maximum Read Request Size of PCI Express Device or allow System BIOS select the value. APC-3x82/83 User Manual...
- Page 35 ← Select Screen ↑↓ Select Item Charge Field General Help F10 Save and Exit ESC Exit V02.68 © Copyright 1985-2009 American Mega trends , Inc. Smbios Smi Support: [Enable] [Disabled] 3.4.10 USB Configuration BIOS SETUP UTILITY Advanced APC-3x82/83 User Manual...
- Page 36 V02.68 © Copyright 1985-2009 American Mega trends , Inc. Legacy USB Support: [Enable] [Disabled] USB2.0 Controller Mode: [HiSpeed] [FullSpeed] BIOS EHCI Hand-Off: [Enable] [Disabled] Hotplug USB FDD Support: [Auto] [Disabled] [Enable] USB Mass Storage Device Configuration: BIOS SETUP UTILITY APC-3x82/83 User Manual...
-
Page 37: Advanced Pci/Pnp Settings
[No] PCI Latency Timer [64] Allocate IRQ to PCI VGA [Yes] Palette Snooping [Disabled] PCI IDE BusMaster [Enabled] ← Select Screen OffBoard PCI/ISA IDE Card [Auto] ↑↓ Select Item +- Charge Field IRQ3 F1 General Help [Available] APC-3x82/83 User Manual... - Page 38 V02.68 © Copyright 1985-2009 American Mega trends , Inc. Clear NVRAM: [No] [Yes] Plug & Play OS: [No] [Yes] PCI Latency Timer: [64] [32] [96] [128] [160] [192] [224] [248] Allocate IRQ to PCI/VGA: [Yes] [No] Palette Snooping: [Disabled] [Enable] PCI IDE BusMaster: [Disabled] APC-3x82/83 User Manual...
- Page 39 Available: Specified DMA is available to be used by PCI/PnP devices. Reserved: Specified DMA is reserved for use by legacy ISA devices. Reserved Memory Size: Size of memory block to reserve for legacy ISA devices. [Disabled] [16k] [32k] [64k] APC-3x82/83 User Manual...
-
Page 40: Boot Settings
Allows BIOS to skip certain tests while booting .This will decrease the time needed to boot the system. Quiet Boot: [Disabled] [Enabled] Disabled: Displays normal POST messages. Enabled: Displays OEM logo instead of POST messages. AddOn ROM Display Mode: Set display mode for Option ROM. APC-3x82/83 User Manual... - Page 41 [Disabled] Hit „DEL‟Messgae Display : Displays “press” DEL to run Setup in POST. [Enabled] [Disabled] Interrupt 19 Capture: [Disabled] [Enabled] Enabled: Allows option ROMs to trap interrupt 19. Boot Device Priority: Specifies the Boot Device Priority sequence. APC-3x82/83 User Manual...
-
Page 42: Security Settings
[Disabled] [Enabled] Enabled / Disabled Boot Sector Virus Protection. Type the password with up to 6 characters and then press Enter key. This will clear all previously typed CMOS passwords. You will be requested to confirm the APC-3x82/83 User Manual... -
Page 43: Advanced Chipset Settings
Enter Go to sub screen General Help F10 Save and Exit ESC Exit V02.68 © Copyright 1985-2009 American Mega trends , Inc. Note: Due to limited address length of BIOS, only a portion of panel parameters are listed in APC-3x82/83 User Manual... - Page 44 V02.68 © Copyright 1985-2009 American Mega trends , Inc. DRAM Frequency: [Auto] [Max MHz] Configure DRAM Timing By SPD: [Enabled] [Disabled] Initate Graphic Adapter: Select which graphics controller to use as the primary boot device. [IGD] [PCI/IGD] [PCI/PEG] [PEG/IGD] APC-3x82/83 User Manual...
- Page 45 +- Charge option [1024x768LVDS] F1 General Help Panel Backlight Control [Level 9] F10 Save and Exit HDCP Support ESC Exit Disabled] V02.68 © Copyright 1985-2009 American Mega trends , Inc. DVMT Mode Select: [DVMT Mode] [FIXED Mode] APC-3x82/83 User Manual...
- Page 46 PCI MMIO Allocation: 4Gb To 3072MB Auto DRAM Frequency [Auto] Max MHz Configure DRAM Timing by SPD [Enabled] Initate Graphic Adapter [IGD] ← Select Screen Internal Graphics Mode Select ↑↓ Select Item [Enable,8MB] Charge Field General Help PEG Port Configuration APC-3x82/83 User Manual...
- Page 47 Select which graphics controller to use as the primary boot device. [IGD] [PCI/IGD] [PCI/PEG] [PEG/IGD] [PCIE/PCI] Internal Graphics Mode Select: [Enabled, 8MB] Video Function Configuration: BIOS SETUP UTILITY Chipset Video Function Configuration Options DVMT Mode Select [DVMT Fixed Mode Mode] DVMT Mode APC-3x82/83 User Manual...
- Page 48 V02.68 © Copyright 1985-2009 American Mega trends , Inc. DVMT Mode Select: [DVMT Mode] [FIXED Mode] DVMT/FIXED Memory Size: [256MB] [128MB] [Maximum DVMT] Boot Display Device: [VBIOS-Default] [CRT] [LVDS] [CRT + LVDS] Flat Panel Type: [1024x 768LVDS] [640x480LVDS] [800x600LVDS] [1280x1024LVDS] [1366x768LVDS] APC-3x82/83 User Manual...
-
Page 49: Exit Options
Save Changes and Exit: Save configuration changes and exit setup? F10 key can be used for this operation) [OK] [Cancel] Discard Changes and Exit: Discard Changes and Exit setup? ESC key can be used for this operation) [OK] APC-3x82/83 User Manual... -
Page 50: Examples Of Gpio Programming
3. Activate the logic device GPIO Port 6 4. Configure GPIO Port 6 register 5. Select logic device number 9 6. Activate the logic device GPIO Port 2 7. Configure GPIO Port 2 register 8. Exit the extended function mode APC-3x82/83 User Manual... - Page 51 4Eh mov al, 007h ;LDN selection register out dx, al mov dx, 4Fh mov al, 008h ;Select LDN=8, GPIO Port6 ;or Select LDN9, GPIO Port2 out dx, al Example C code: outportb(0x4E, 0x07); //LDN selection register APC-3x82/83 User Manual...
- Page 52 4Eh mov al, 0E4h ;GPIO I/O selection reg. out dx, al mov dx, 4Fh mov al, 0FFh ;0 – Output, 1 – Input ;or mov al, 0F0h to set output out dx, al APC-3x82/83 User Manual...
- Page 53 00000100b ;Bit2 = GPO62 out dx, al ;Clear GPO62 mov dx, 4Eh mov al, 0E5h ;GPIO data reg. out dx, al mov dx, 4Fh in al, dx and al, not 00000100b out dx, al APC-3x82/83 User Manual...
- Page 54 //Exit super I/O programming mode #define EXITPRG { \ outportb(INDEXP, 0xAA);} //Select logic device number #define SELETDEV(ldn) { \ outportb(INDEXP, 7); \ outportb(DATAP, ldn); } //Initialize the GPIO port2 int InitGP2() { //Start the super I/O chip programming APC-3x82/83 User Manual...
- Page 55 //Start the super I/O chip programming ENTERPRG //Select the logical device 8, GP6 SELETDEV(8) //Activate GP1 WRITEREG(0x30, (inportb(0x30)|0x4)) WRITEREG(0xE6, 0x0) WRITEREG(0xE4, 0xF0) //Exit the super I/O chip programming EXITPRG return 0; //Read GPIO Port2 unsigned char ReadGP2() { unsigned char cGP2; APC-3x82/83 User Manual...
- Page 56 //Start the super I/O chip programming ENTERPRG //Select the logical device 8, GP6 SELETDEV(8) //Write GP1 value WRITEREG(0xE5, cGP6) //Exit the super I/O chip programming EXITPRG return 0; int main() { unsigned char cGP; //Initialize the GPIO port InitGP2(); APC-3x82/83 User Manual...
- Page 57 InitGP6(); //Read GPIO Port 2 cGP = ReadGP2(); printf("\nRead GPIO Port 2 Status: %X", cGP); //Write GPIO Port 6 WriteGP6(cGP); printf("\nSet GPIO Port 6 Status: %X", cGP); return 0; APC-3x82/83 User Manual...
-
Page 58: Chapter 4 Installation Of Drivers
ALC662 HD Audio Driver, Touch Panel Driver. Installation instructions are given below. Important Note: After installing your Windows operating system (Windows XP), you must install first the Intel Chipset Software Installation Utility before proceeding with the installation of drivers. APC-3x82/83 User Manual... -
Page 59: Intel Chipset Driver
4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1. Access Industrial Panel PC. Select Intel(R) Chipset Atom D525 + Intel ICH8M. Step 2. Click Next to setup program. APC-3x82/83 User Manual... - Page 60 Step 3. Read the license agreement. Click Yes to accept the terms of the license agreement. Step 4. Click Next to continue. APC-3x82/83 User Manual...
- Page 61 Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. Click Finish then remove any installation media from the drives. APC-3x82/83 User Manual...
-
Page 62: Intel Gma 3150 Vga Chipset Driver
4.2 Intel GMA 3150 VGA Chipset Driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1. Select Intel(R) GMA 3150 VGA Chipset. Step 2. Click Next to continue. APC-3x82/83 User Manual... - Page 63 Step 3. Click Next to continue setup program. Step 4. Read the license agreement. Click Yes to accept the license agreement. APC-3x82/83 User Manual...
- Page 64 Step 5. Click Next. Step 6. Click Next to continue. APC-3x82/83 User Manual...
- Page 65 Step 7. Select Yes, I want to restart this computer now. Click Finish then remove any installation media from the drivers. APC-3x82/83 User Manual...
-
Page 66: Intel 82574L Network Adapter Driver
4.3 Intel 82574L Network Adapter Driver To install the Intel 82574L Network adapter Driver, please follow the steps below. Step 1. Select Intel(R) 82574L Network Adapter. Step 2. Click Next to continue. APC-3x82/83 User Manual... - Page 67 Step 3. Read license agreement. Select I accept the terms in the license agreement then click Next to continue. Step 4. Select Drivers, Intel(R) PROSet for Windows* Device Manager, Advanced Network Services. Click Next to continue. APC-3x82/83 User Manual...
- Page 68 Step 5. Click Install to begin the installation. Step 6. Click Finish to compete the installation. APC-3x82/83 User Manual...
-
Page 69: Realtek Hd Audio Driver Installation
To install the Realtek High Definition (HD) Audio driver, please follow the steps below. Step 1. Select Realtek ALC662 HD Audio Driver from the list. Step 2. Wait for extracting the files then click Next to continue. APC-3x82/83 User Manual... - Page 70 Step 3. Click Yes to continue the installation. Step 4. Wait for installation. APC-3x82/83 User Manual...
- Page 71 Step 5. Select Yes, I want to restart my computer now. then click OK. APC-3x82/83 User Manual...
-
Page 72: Chapter 5 Touch Screen Installation
PM6500, PM6300. 5.2.1 Installing Software If you have an older version of the PenMount Windows 2000/XP driver installed in your system, please remove it first. Follow the steps below to install the PenMount DMC6000 Windows 2000/XP driver. APC-3x82/83 User Manual... - Page 73 “Unknown Device”. Do not use this hardware wizard. Press Cancel. Step 2. Insert the Aplex product CD install setup.exe. the screen below would appear. Se touch panel driver Step 3. Click Next to continue.
- Page 74 Step 4. Read the license Agreement. Click I agree to agree the license agreement. Step 5. Choose the folder in which to install PenMount Windows Universal Driver. Click Install to start the installation. APC-3x82/83 User Manual...
- Page 75 Step 6. Wait for installation. Then click Next to continue. Step 7. Click OK. APC-3x82/83 User Manual...
- Page 76 Step 8 Click Finish to compete installation. APC-3x82/83 User Manual...
-
Page 77: Software Functions
„Advanced Calibration‟ adjusts aging touch screens. Standard Calibration Click this button and arrows appear pointing to red squares. Use your finger or stylus to touch the red squares in sequence. After the fifth red point calibration is complete. To skip, press „ESC‟. APC-3x82/83 User Manual... - Page 78 -calibration 0 ( Standard Calibration) Dmcctrl.exe - calibration ($) 0= Standard Calibration 4=Advanced Calibration 4 9=Advanced Calibration 9 16=Advanced Calibration 16 25=Advanced Calibration 25 Step 1. Please select a device then click Configure. You can also double click the device too. APC-3x82/83 User Manual...
- Page 79 Step 2. Click Standard Calibration to start calibration procedure NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy. Please follow the step as below: APC-3x82/83 User Manual...
- Page 80 Step 3. Come back to PenMount Control Panel and select Tools then Click Advanced Calibration. Step 4. Select Device to calibrate, then you can start to do “Advanced Calibration”. NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy. APC-3x82/83 User Manual...
- Page 81 Setting APC-3x82/83 User Manual...
- Page 82 About This panel displays information about the PenMount controller and driver version. APC-3x82/83 User Manual...
- Page 83 Please note once you turn on this function the Rotating function is disabled. Enable the multiple display function as follows: Step 1. Check the Multiple Monitor Support box; then click Map Touch Screens to assign touch controllers to displays. APC-3x82/83 User Manual...
- Page 84 Just follow the regular procedure for calibration on each of your desktop monitors. 2. The Rotating function is disabled if you use the Multiple Monitors function. 3. If you change the resolution of display or screen address, you have to redo Map Touch Screens so APC-3x82/83 User Manual...
- Page 85 4. If you more monitor mapping one touch screen, Please press „S‟ to skip mapping step. Tools Draw Tests or demonstrates the PenMount touch screen operation. Advanced Calibration Enable Advanced Calibration function Right Button Icon Enable right button function. The icon can show on Desktop or System Tray (menu bar). APC-3x82/83 User Manual...
- Page 86 You can see how many devices of PenMount controller that are plugged to your system PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you turn on PenMount Monitor in PenMount Utilities. PenMount Monitor has the following function APC-3x82/83 User Manual...
- Page 87 2. Choose the rotate function (0°, 90°, 180°, 270°) in the 3rd party software. The calibration screen appears automatically. Touch this point and rotation is mapped. NOTE: The Rotate function is disabled if you use Monitor Mapping APC-3x82/83 User Manual...
Need help?
Do you have a question about the APC-3x82 and is the answer not in the manual?
Questions and answers