Speaker Setting; X'over Setting - Kenwood KDC-X998 Instruction Manual

DSP settings (KDC-X998, KDC-BT958HD)

5-4. Speaker setting

The speaker X'Over is automatically set when the
position and size of each speaker are selected from
the following items.
1
Press [SRC] and select a source other than
Standby ("STANDBY") using [Control] knob.
Refer to <Source selection> (page
2
Press [Control] knob.
Enters the Function setting mode.
3
Select "Audio Control"
"Speaker Setting" using [Control] knob.
For how to use [Control] knob, refer to
to select the item> (page
4
Select a speaker type using [Control] knob.
Speaker type Setting item Setting value
"Front" Front speaker
location
"SIZE"
"TW"
"Rear" Rear speaker
location
"SIZE"
"SubWoofer" "SIZE"
text: Factory setting)
(Colored
[1] Value set when "Minivan" or "Minivan (Long)" is selected
as described in <5-3. Car type selection> (page
5
Select a setting item using [Control] knob.
6
Select a setting value using [Control] knob.
Exiting from the Function setting mode
Press and hold [1/6].
20
|
KDC-X998/ KDC-BT958HD/ KDC-X898/ KDC-BT858U
14).
> "Pro Setup" >
<3-3. How
13).
"Door", "On Dash", "Under Dash"
Front speaker size
KDC-X998
"O.E.M.", "3 1/2in", "4in", "4 3/4in",
"5in", "6 1/2in", "6 3/4in", "7in",
"4x6", "5x7", "6x8", "6x9", "7x10"
KDC-BT958HD
"Small", "Medium", "Large"
Tweeter size
"None", "Small", "Medium", "Large"
"Door", "Rear Deck"
("2nd Row", "3rd Row"[1])
Rear speaker size
KDC-X998
"None", "O.E.M.", "3 1/2in", "4in", "4
3/4in", "5in", "6 1/2in", "6 3/4in",
"7in", "4x6", "5x7", "6x8", "6x9",
"7x10"
KDC-BT958HD
"None", "Small", "Medium", "Large"
Speaker Size Subwoofer
KDC-X998
"None", "6 1/2inch", "8inch",
"10inch", "12inch", "15inch Over"
KDC-BT958HD
"None", "Small", "Large"
19).

5-5. X'Over setting

Fine adjusting the following setting values
corresponding to the X'Over values set in the
section <5-4. Speaker setting> (page
1
Press [SRC] and select a source other than
Standby ("STANDBY") using [Control] knob.
Refer to <Source selection> (page
2
Press [Control] knob.
Enters the Function setting mode.
3
Select "Audio Control"
"X'Over" using [Control] knob.
For how to use [Control] knob, refer to
to select the item> (page
4
Select a speaker type using [Control] knob.
Speaker type Setting item Setting value
"Front" "FC"
"SLOPE"[1][2]
"GAIN"
"Rear" "FC"
"SLOPE"[1][2]
"GAIN"
"SubWoofer" "FC"
"SLOPE"[1][2]
"GAIN"
"PHASE"
20).
14).
> "Pro Setup" >
<3-3. How
13).
Front high pass filter
KDC-X998
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 Hz
KDC-BT958HD
Through, 40, 60, 70, 80, 100, 120,
150, 180, 220 Hz
Front high pass slope
-6, -12, -18, -24 dB/Oct
Front gain
-8 ,-7, -6, -5, -4, -3, -2, -1, 0 dB
Rear high pass filter
KDC-X998
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 Hz
KDC-BT958HD
Through, 40, 60, 70, 80, 100, 120,
150, 180, 220 Hz
Rear high pass slope
-6, -12, -18, -24 dB/Oct
Rear Gain
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
Subwoofer low pass filter
KDC-X998
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through Hz
KDC-BT958HD
40, 60, 70, 80, 100, 120, 150, 180,
220, Through Hz
Subwoofer slope
-6, -12, -18, -24 dB/Oct
Subwoofer gain
-8 ,-7, -6, -5, -4, -3, -2, -1, 0 dB
Subwoofer phase
"REV" (180°)/ "NML" (0°)