Table 10: Ht488 Fxs Port S - Grandstream Networks HT-488 User Manual

T 10: HT488 FXS PORT S
ABLE
SIP Server
Outbound Proxy
SIP User ID
Authenticate ID
Authentication Password
Name
Use DNS SRV:
User ID is Phone Number
SIP Registration
Unregister on Reboot
Register Expiration
Local SIP port
Local RTP port
Use Random Port
Grandstream Networks, Inc.
•
inbound and outbound calls (INFO level)
•
registration status change (INFO level)
•
negotiated codec (INFO level)
•
Ethernet link up (INFO level)
•
SLIC chip exception (WARNING and ERROR levels)
•
memory exception (ERROR level)
The Syslog uses USER facility. In addition to standard Syslog payload, it contains the
following components:
GS_LOG: [device MAC address][error code] error message
Here is an example: May 19 02:40:38 192.168.1.14 GS_LOG: [00:0b:82:00:a1:be][000]
Ethernet link is up
P D
ETTINGS AGES EFINITIONS
This field contains the URI string or the IP address (and port, if different from 5060) of
the SIP proxy server. e.g., the following are some valid examples: sip.my-voip-
provider.com, or sip:my-company-sip-server.com, or 192.168.1.200:5066
IP address or Domain name of Outbound Proxy, or Media Gateway, or Session Border
Controller. Used by ATA for firewall or NAT penetration in different network
environment. If symmetric NAT is detected, STUN will not work and ONLY Outbound
Proxy will work.
User account information, provided by VoIP service provider (ITSP), usually has the
form of digit similar to phone number or actually a phone number. This field contains
the user part of the SIP address for this phone. e.g., if the SIP address is
sip:my_user_id@my_provider.com, then the SIP User ID is: my_user_id.
Do NOT include the preceding "sip:" scheme or the host portion of the SIP address in
this field.
ID used for authentication, usually same as SIP user ID, but could be different and
decided by ITSP.
Password for ATA to register to (SIP) servers of ITSP. Purposely blank out once saved
for security. Maximum length is 25.
SIP service subscriber's name which will be used for Caller ID display
Default is No. If set to Yes the client will use DNS SRV to lookup for the SIP server.
If "Yes" is set, a "user=phone" parameter will be attached to the "From" header in SIP
request
This parameter controls whether the HandyTone ATA needs to send REGISTER
messages to the proxy server. The default setting is "Yes".
Default is No. If set to yes, the device will first send registration request to remove all
previous bindings. Use only if proxy supports this remove bindings request.
This parameter allows the user to specify the time frequency (in minutes) the
HandyTone ATA refreshes its registration with the specified registrar. The default
interval is 60 minutes (or 1 hour). The maximum interval is 65535 minutes (about 45
days).
This parameter defines the local SIP port the HandyTone ATA will listen and transmit.
The default value for FXS port is 5060.
This parameter defines the local RTP-RTCP port pair the HandyTone ATA will listen
and transmit. It is the base RTP port for channel 0. When configured, channel 0 will use
this port _value for RTP and the port_value+1 for its RTCP; channel 1 will use
port_value+2 for RTP and port_value+3 for its RTCP. The default value for FXS port is
5004.
Default No. If set to Yes, the device will pick randomly-generated SIP and RTP ports.
HT488 User Manual
Firmware 1.0.3.64
Page 22 of 33
Last Updated: 4/2007