Denon AVR-4310 Owner's Manual page 40

ENGLISH
Making Detailed Settings (Manual Setup)
Setting items
Surround Speaker DOLBY/DTS Cinema : Set the surround speakers to use during Dolby/
Set the surround speakers DTS Cinema mode.
to use for every surround DOLBY/DTS Music : Set the surround speakers to use during Dolby/DTS
mode. Music mode.
DOLBY Game : Set the surround speakers to use during Dolby Game
mode.
DOLBY Height : Set the surround speakers to use during Dolby Height
mode.
WIDE SCREEN : Set the surround speakers to use during WIDE SCREEN
mode.
7CH STEREO : Set the surround speakers to use during 7CH STEREO
mode.
DSP SIMULATION : Set the surround speakers to use during the DENON
original surround mode.
MULTI CH MODE : Set the surround speakers to use during PCM or DSD
multi-channel mode.
• A : Use surround speakers A.
• B : Use surround speakers B.
• A+B : Use surround speakers A and B.
• "Surround Speaker" is displayed when "Speaker Configuration" –
"Surround A" and "Surround B" setting (vpage 34) is set to "Large"
or "Small".
• When using the PRE OUT terminal, set to "A" or "B".
• Make the surround speaker settings when the input mode is set to "EXT.
IN" at "EXT. IN Setup" (vpage 37).
• When the "Speaker Configuration" – "Surround A" or "Surround B"
setting (vpage 34) is "Small", and using surround speakers A and B
simultaneously, playback is with the same output as when "Surround A"
and "Surround B" are set to "Small".

Main remote control
operation buttons
Setting contents
:Displaying the menu
Cancel the menu
Making the HDMI Settings (HDMI Setup)
Make settings for HDMI video/audio output.
Setting items
RGB Range Normal : Output with RGB video range (16 (black) to 235 (white)).
Set the video range of RGB Enhanced : Output with RGB video range (0 (black) to 255 (white)).
output from the HDMI
This setting is valid when using a TV equipped with a DVI terminal.
terminal.
Vertical Stretch ON : Expand image signal in vertical direction.
Expand image signal in OFF : Do not expand signal in vertical direction.
vertical direction.
This setting is valid with respect to the HDMI output when using an
HDMI-compatible TV. When not using an HDMI-compatible TV, it is
valid with respect to the analog output.
Auto Lip Sync ON : Compensated.
Automatic compensation OFF : Not compensated.
for timing shift in audio and
video output.
HDMI Audio Out Amp : Playback through speakers connected to the receiver.
Select HDMI audio output TV : Playback through TV connected to the receiver.
device.
When the HDMI control function is operating, the setting of audio
playback in the connected TV takes priority (vpage 77 "HDMI
Control Function").
Monitor Out Auto (Dual) : The presence of a TV connected to the MONITOR 1 or
Make settings for HDMI MONITOR 2 terminal is detected automatically, and that TV connection
monitor output. is used.
Monitor 1 : A TV connected to the MONITOR 1 terminal is always used.
Monitor 2 : A TV connected to the MONITOR 2 terminal is always used.
• If both the Monitor 1 and 2 connectors are connected and "Resolution"
(vpage 49) is set to "Auto", the signals are output with a resolution
compatible with both TV.
• With "Resolution" (vpage 49) not set to "Auto", check whether
the TV you are using is compatible with the resolution under "HDMI
Information" – "Monitor 1" and "Monitor 2" (vpage 74).
• Depending on the monitor you have connected, the display may not be
correct when you set to "Auto (Dual)". In such a case, set to either
"Monitor 1" or "Monitor 2".
• You can also set "Monitor Out" by pressing
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
Default settings are underlined.
Setting contents
[M.SEL]
.
See overleaf
:Return to previous menu