Table of Contents
Advertisement
Setting items
Distance
Default : Reset all distance settings to factory default.
(Continued)
•
Yes : Reset to the defaults.
•
No : Do not reset to the defaults.
When you select "Default" and press
to the default?" prompt is displayed. Select either "Yes" or "No",
and press
Front L / Front R / Center / Subwoofer / Surround A L / Surround A R
/ Surround B L / Surround B R / Surr. Back L z / Surr. Back R z / Front
Height L / Front Height R / Front Wide L / Front Wide R : Select the
speaker.
z: When the "Speaker Configuration" – "Surround Back" setting
(vpage 34) is set to "1spkr", "Surr. Back" is displayed.
•
0.00m ~ 18.00m / 0.0ft ~ 60.0ft : Set the distance.
•
Speakers set to "None" in "Speaker Configuration" (vpage 33) are
not displayed.
•
The speakers that can be selected differ depending on the "Amp Assign"
(vpage 33) and "Speaker Configuration" (vpage 33) settings.
•
Default settings :
Front / Center / Subwoofer / Front Height / Front Wide : 3.60 m (12.0 ft)
Surround A / Surround B / Surround Back : 3.00 m (10.0 ft)
•
Set the difference in the distance between the speakers to less than 6.0
meters (20 feet).
Channel Level
Surround Speaker : Set the surround speakers to output the test tone.
Set the volume of the test
•
A : Output test tone from surround speakers A.
tone to be the same when it
•
B : Output test tone from surround speakers B.
is output from each speaker.
•
A+B : Output test tone from surround speakers A and B.
Can be set when the "Speaker Configuration" – "Surround A" or
"Surround B" setting is "Large" or "Small" (vpage 34).
Test Tone : Output test tone.
•
Front L / Front Height L / Center / Front Height R / Front R / Front
Wide R / Surround R /Surr. Back R z /Surr. Back L z / Surround L /
Front Wide L / Subwoofer : Select the speaker.
z : When the "Speaker Configuration" – "Surround Back" setting
(vpage 34) is set to "1spkr", "Surr. Back" is displayed.
•
–12dB ~ +12dB (0dB) : Adjust the volume.
Main remote control
operation buttons
Setting contents
ENTER
, the "Return all settings
ENTER
.
:Displaying the menu
Cancel the menu
Setting items
Channel Level
(Continued)
•
Speakers set to "None" in the "Speaker Configuration" (vpage 33)
settings are not displayed.
•
When
"Subwoofer" setting switches to "OFF".
•
When using surround speakers, be sure to adjust the volume of the
different speakers.
•
When a headphones jack is inserted in the PHONES terminal of the AVR-
4310, the "Channel Level" is not displayed.
•
You can also press
Volume of the Different Speakers").
Default : Reset all channel level settings to factory default.
•
Yes : Reset to the defaults.
•
No : Do not reset to the defaults.
Crossover Frequency
40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
Outputs
at
below
set
250Hz : Set the crossover frequency.
frequency, each speaker's
Advanced : Specify crossover frequency for each speaker.
bass signal output from
•
Front / Center / Surround A / Surround B / Surround A+B / Surround
the subwoofer. Set this
Back / Front Height / Front Wide : Select the speaker.
according
to
the
low
•
40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz /150Hz / 200Hz /
frequency
reproduction
250Hz : Set the crossover frequency.
capabilities of the speakers
you are using.
•
Can be set when the "Speaker Configuration" – "Subwoofer" (vpage
33) setting is "Yes", or when you have a speaker that is set to "Small".
•
Always set the crossover frequency to "80Hz". When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
•
For speakers set to "Small", sound below the crossover frequency is cut
from the sound output. The cut bass sound is output from the subwoofer
or front speakers.
•
The speakers that can be set when "Advanced" is selected differ
according to the "Subwoofer Mode" setting (vpage 34).
•
When "LFE" is selected, speakers set to "Small" at "Speaker
Configuration" can be set. If the speakers are set to "Large", "Full
Band" is displayed and the setting cannot be made.
•
If set to "LFE+Main", this setting can be made regardless of the
speaker size.
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
Making Detailed Settings (Manual Setup)
Setting contents
o
is pressed while the subwoofer volume is set to "–12 dB", the
[CHANNEL LEVEL]
to set (vpage 78 "Adjust the
:Return to previous menu
ENGLISH
See overleaf
Hide quick links:
Advertisement
Table of Contents
