Disclaimer; Important Safety Instructions - CHIEF WM210S Installation Instructions Manual

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:
A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION:
A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING:
Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer's responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING:
Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer's responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (15.9mm) for
wood studs; and a minimum drywall thickness of 1/2"
(12.7mm) for steel studs.
WARNING:
Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING:
Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING:
Do not use this product outdoors.
2
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer's responsibility to make sure the combined weight of
all components attached to the short throw projector mounts
do not exceed the mounting system's weight capacity. (See
Table 1)
• The weight capacity of the short throw projector
mounts may be LIMITED to the lowest weight
capacity of any other component or accessory
used within the mounting system!
IMPORTANT ! :
The short throw projector mounts are
designed to be mounted to an 8" concrete, 8"x8"x16" concrete
block, 2" x 4" wood studs (16" on center), or 2" x 4"-25ga
minimum steel studs wall.
--SAVE THESE INSTRUCTIONS--
Table 1: Weight Capacities
Model Maximum Weight Capacity of
WM210S 50 lbs (22.7 kg)
WM220S 50 lbs (22.7 kg)
WM230S 25 lbs (11.3 kg)
WM240S 25 lbs (11.3 kg)
WM210AUS 25 lbs (11.3 kg)
WM220AUS 25 lbs (11.3 kg)
WM230AUS 25 lbs (11.3 kg)
WM240AUS 25 lbs (11.3 kg)
WM210SI 50 lbs (22.7 kg)
WM220SI 50 lbs (22.7 kg)
WM230SI 25 lbs (11.3 kg)
WM240SI 25 lbs (11.3 kg)
WM210AUSI 25 lbs (11.3 kg)
WM220AUSI 25 lbs (11.3 kg)
WM230AUSI 25 lbs (11.3 kg)
WM240AUSI 25 lbs (11.3 kg)
Installation Instructions
Mounting System