Table of Contents
Advertisement
Quick Links
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
This device complies with part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio or television
communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment to an outlet on a circuit other than that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Suspended Ceiling Lift
SL220
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CHIEF SL220
Summary of Contents for CHIEF SL220
- Page 1 Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment to an outlet on a circuit other than that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help SL220...
-
Page 2: Table Of Contents Disclaimer
It ELECTRIC SHOCK: is the installer’s responsibility to make sure the weight of all components attached to the SL220 does not exceed 30 lbs Always turn off power at source before cleaning. (13.6 kg). -
Page 3: Table Of Contents
Preparing SL220 Framework......6 Replacing Ceiling Pan........14 Installing SL220 Framework....... 6 OPERATING MODES........14 Securing SL220 Frame to Ceiling Structure..7 Projector Shutdown Mode (Optional)....14 Solid Concrete Ceiling Structure....7 Current Sense Mode (Optional)......14 Steel Truss Ceiling Structure......7 Fault Condition.......... -
Page 4: Tools Required For Installation
Installation Instructions SL220 TOOLS REQUIRED FOR INSTALLATION PARTS A (1) [SL220 Lift] B (1) [SL220 Frame] D (4) [Horizontal Bracket] [2 right, 2 left] C (4) F (4) E (4) [Vertical Bracket] 6-32 x 5/16" 6-32 x 1/2" N (5) -
Page 5: Legend
Installation Instructions SL220 LEGEND Tighten Fastener Phillips Screwdriver Apretar elemento de fijación Destornillador Phillips Befestigungsteil festziehen Kreuzschlitzschraubendreher Apertar fixador Chave de fendas Phillips Serrare il fissaggio Cacciavite a stella Bevestiging vastdraaien Kruiskopschroevendraaier Serrez les fixations Tournevis à pointe cruciforme Loosen Fastener Adjust Aflojar elemento de fijación... -
Page 6: Preparing For Installation
SL220. OPTIONAL: Attach vertical brackets (C) to both sides (in each corner) of the SL220 frame (B) using a 06-32 x 5/16" Phillips flat head screw (F). (See Figure 1) Attach horizontal bracket (D) over the vertical bracket (C) at each corner of the SL220 frame using a 06-32 x 1/2"... -
Page 7: Securing Sl220 Frame To Ceiling Structure
Examine ceiling structure (concrete, steel truss, or wood) above SL220 frame (B) to identify four support cable anchor locations. Each location should be approximately 15° outside of support holes in SL220 frame (B). Mark (J3) locations with pencil. (See Figure 4). -
Page 8: Wood Ceiling Structure
Install Listed electrical box (not included) to outlet box attachment plate (H). Install the plate (H) with attached electrical box onto the SL220 frame (B) using two 8-32 x 1/4" Phillips screws (G). (See Figure 9) IMPORTANT ! : The junction box must be installed onto the back of the frame (i.e. -
Page 9: Electrical Rating
Wire outlet into junction box in accordance with all local Figure 10 codes and ordinances. PREPARING THE SL220 Carefully inspect the SL220 for any shipping damage. If any damage is apparent, do NOT continue with the installation. Instead, contact Chief for further instructions. Removing Ceiling Pan Place SL220 upside down on clean surface. -
Page 10: Removing Projector Cradle (Optional)
Grounding strap meets IEC-60320 and on the other end is appropriate for use with the grounded main outlet. Plug power cord into IEC inlet on rear panel inside SL220. (See Figure 11) (Some parts removed for clarity) -
Page 11: Placing Sl220 Into Ceiling Structure
Installation Instructions SL220 Secure the SL220 (A) to the SL220 frame (B) using four 8-32 x 1" Phillips head screws (L), two in the front and two in the back of the SL220. (See Figure 17) Secure the outlet box attachment plate (H) to the SL220 using one 8-32 x 1"... -
Page 12: Replacing Projector Cradle
Installing RPA/RPM, Bracket and Projector Install RPA/RPM (a Listed accessory - not included) to the Figure 18 projector cradle following instructions included with the Line up rear spacers with attachment holes on SL220 arms. RPA/RPM. (See Figure 21) (See Figure 19) Tighten rear spacers. -
Page 13: Adjustments
SL220 cross bracket. (See Figure 22) NOTE: Ensure that IR sensor "eye" has "line of sight" to the Slide the SL220 cross bracket to the left or right as required. remote control signal. Tighten wing nuts. (See Figure 22) Insert terminal block (R) into SL220. -
Page 14: Replacing Ceiling Pan
Sense mode. removes power from the projector when the lift is retracted. This prevents possible damage to the projector if the SL220 is Turn on the projector so that the lift will learn the normal current draw of the projector. -
Page 15: Fault Condition
Installation Instructions SL220 Fault Condition IMPORTANT ! : If the SL220 control system sees a fault condition it will stop the operation and a red light will flash on the control board (visible through the control housing). For most faults: Correct the problem. -
Page 16: Rs485 Information
SL220 Installation Instructions RS485 Information Communication parameters as specified in ANSI TIA/EIA-485-A: Table 2: COMMAND STRINGS FOR SL-220 Baud Data Parity Stop Flow Rate Length Control 9600 8 Bits None None • The serial control command string is set up as follows:... -
Page 17: Remote Control Capabilities
Installation Instructions SL220 Remote Control Capabilities The remote control has a range of 20-30ft (6-9m), and is powered by 2 AAA batteries that are accessed from the back of the remote. NOTE: If operation of the mount is required at a greater distance than remote control will allow, the mount can be controlled through other methods. -
Page 18: Table 4: Wiring Table
SL220 Installation Instructions Table 4: WIRING TABLE... - Page 19 Installation Instructions SL220...
- Page 20 A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands Chief Manufacturing, a products division P +31 (0)40 2668620 of Milestone AV Technologies F +31 (0)40 2668615 Asia Pacific A Office No.
Need help?
Do you have a question about the SL220 and is the answer not in the manual?
Questions and answers