Casablanca BEL AIR Owner's Manual page 15

Before requesting service: Please follow this troubleshooting guide before contacting your dealer for assistance.
Caring for Finishes: For cleaning, a soft brush or lint-free cloth
should be used to prevent scratching the finish. A vacuum cleaner
brush nozzle can remove heavier dust. Surface smudges or an ac-
cumulation of dirt and dust can easily be removed by using a mild
detergent and slightly dampened soft cloth. An antistatic agent
may be used, but never use abrasive cleaning agents. These will
damage the finish. Painted and high-gloss blades may be cleaned
in the same manner.
Blades: Wood finish blades should be cleaned with a furniture
polishing cloth. Occasionally, a light coat of furniture polish may
be applied for added protection and beauty.
PROB-
PRObLEM
FAN WILL NOT START-Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections,
making sure the power is turned off during this inspection.
-Pin connectors are not making good contact. Check all connections.
-Battery weak—install fresh battery.
-Fan receiver defective—replace.
FAN DOES NOT RESPOND
TO REMOTE CONTROL
FAN WOBBLES OR SHAKES
-Check that bladeholders have not been bent during installation and blades are balanced.
EXCESSIVELY
-Hanger bracket and/or ceiling outlet are loosely attached: Make sure that the hanger bracket is tightly
attached to the ceiling outlet box. Make sure that the downrod assembly is secured firmly.
-Downrod is loosely attached to downrod base: Make sure that all screws are securely tightened.
-Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s).
FAN NOISY DURING
OPERATION
-Tighten canopy screws and mounting plate assembly. Check that the wire nuts inside the canopy and
switch housing are not touching the metal parts or have fallen off the wire splices. Tighten as necessary.
-Tighten blade holders to flywheel (or direct drive motor)/and blade to bladeholder screws.
-Make sure all screws in the motor housing are snug, but not overly tight. Defective bulb: Replace bulb.
-If new, "break-in" may be required - run at higher speed for several days.
DOES NOT RUN ON
LOW SPEED
-Not using Alkaline batteries: Replace with ALKALINE batteries.
BATTERY LIFE
SEEMS SHORT
faN o.K., No liGht: Check for burned out light bulb. Check fan light wires.
liGht o.K., No faN: Check connectors, may not be making good contact.
reMote CoNtrol of faN is erratiC: Check batteries installed correctly. Install fresh ALKALINE batteries.
faN starts worKiNG By itself: Frequency interference; Change dip switch code.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interfer-
ence received, including interference that may cause undesired operation.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the
receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer
or an experienced radio/TV technician for help. Note: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one's authority to operate this
remote control.
TROUbLESHOOTING
Never Lubricate this Fan!
The precision motor at the heart of your Casablanca fan features
sealed bearings that are lubricated for life. Do not attempt to oil
the motor.
Changing Light Bulbs
Be sure to turn power to the fan OFF at the wall switch or circuit
breaker before changing light bulbs. Replace bulbs with same type as
removed from the fixture. Each fan is rated for a maximum TOTAL
wattage of lighting.
Exceeding the rated maximum allowable wattage for the fan will
burn out the fan electronics module and void the warranty.
ADVAN•TOUCH
-Power to fan is off.
-Wrong remote is being used.
-Remote dip settings changed—see instructions for changing the frequency setting.
-Be sure canopy pin is properly set into the slot on the ball.
A •T
DVAN OUCH
POSSIBLE REM-
POSSIbLE REMEDIES..
®
15