Identification node with children that specify the Cisco TelePresence Management Suite (TMS) is used as TMS codec from which the notification originated. This means that uses this feedbackslot to register its expressions. you can handle multiple codecs with a single HTTP server URI.
Audio Input HDMI  Mode Requires user role: ADMIN If you are connecting a Cisco camera with an integrated microphone to the codec’s HDMI 1 input, Value space: <Off/On> you can enable/disable audio input on the port; if you are using any other camera, the audio input will be disabled regardless of this setting.
Applies to cameras which support gamma mode. Gamma describes the nonlinear relationship Value space: <Auto/Off/On> between image pixels and monitor brightness. The Cisco TelePresence PrecisionHD 720p camera Auto: When the camera is placed upside down the image is automatically mirrored. Use this supports gamma mode.
Cameras Camera  MotorMoveDetection xConfiguration Cameras Camera  DHCP This setting applies only when using a Cisco TelePresence PrecisionHD 1080p12x camera. Applies to cameras which support DHCP over LAN. When set, the command enables support for software upgrade of daisy chained cameras.
Sip: Sip ensures that calls are set up as SIP calls. Requires user role: ADMIN H320: H320 ensures that calls are set up as H.320 calls (only applicable if connected to a Cisco Value space: <Off/On> TelePresence ISDN Link gateway).
(MCU). LocalOnly: The presentation will only be shown locally. If registered to a Cisco Unified Communications Manager (CUCM) version 8.6.2 or newer, the video system can use either the CUCM conference bridge, or the video system's own built-in MultiSite Example: xConfiguration Conference 1 Presentation Policy: LocalRemote feature.
Format: A valid IPv6 address. be set manually using the Provisioning ExternalManager Address setting. If the Network VLAN Voice Mode setting is Auto and the Cisco Discovery Protocol (CDP) assigns an Example: xConfiguration Network 1 IPv6 Address: "2001:0DB8:0000:0000:0000:0000:0000:000 ID to the voice VLAN, then a request for option 150 will always be sent. That is, the Network DHCP 2"...
Value space: <Auto/Manual/Off> 10half: Force link to 10 Mbps half-duplex. Auto: The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. If CDP is 10full: Force link to 10 Mbps full-duplex. not available, VLAN is not enabled.
Enter the NTP Address to define the network time protocol server address. This address will be you have the Cisco TelePresence Management Suite (TMS) you must make sure the same SNMP used if NTP Mode is set to Manual, or if set to Auto and no address is supplied by a DHCP server.
NetworkServices SNMP SystemContact xConfiguration NetworkServices CTMS Mode Enter the name of the Network Services SNMP System Contact. This setting determines whether or not to allow multiparty conferences controlled by a Cisco TelePresence Multipoint Switch (CTMS). Requires user role: ADMIN Video systems running software TC5.0 or later are able to initiate or join non-encrypted multiparty...
Example: xConfiguration Provisioning Connectivity: Auto Value space: <VCS/TMS/Callway/CUCM> xConfiguration Provisioning Mode VCS: Select VCS if the phonebook is located on the Cisco TelePresence Video Communication Server. It is possible to configure a video system using a provisioning system (external manager). This allows video conferencing network administrators to manage many video systems simultaneously.
Provisioning ExternalManager AlternateAddress Value space: <S: 0, 64> Only applicable when the endpoint is provisioned by Cisco Unified Communication Manager Format: String with a maximum of 64 characters. (CUCM) and an alternate CUCM is available for redundancy. Enter the address of the alternate CUCM.
Thus the shortest route for audio and video is always Requires user role: ADMIN secured between the endpoints. NOTE: ICE is not supported when registered to CUCM (Cisco Value space: <On/Off> Unified Communication Manager).
SIP Profile [1..1] Line Select if the SIP Proxy address is to be obtained manually or by using Dynamic Host Configuration When registered to a Cisco Unified Communications Manager (CUCM) the endpoint may be part Protocol (DHCP). of a shared line. This means that several devices share the same directory number. The different...
The codec can be enabled for Cyrillic input characters in the menus on screen. Requires that Video This requires that the system is bookable by an external booking system, like for example the Cisco OSD InputMethod Cyrillic is set to On.
Video WallPaper Select a background image (wallpaper) for the video screen when idle. The Experimental settings are for testing only and should not be used unless agreed with Cisco. Requires user role: USER These settings are not documented and WILL change in later releases.
Add command. Note that only the first contact method will appear in the Favorites list on the Cisco TelePresence Touch controller. All contact methods are available in the API, on the web interface Name(r): The name of the contact.
You can add several contact methods to a contact. Note that only the first contact method will command was issued to make the contact. appear in the Favorites list on the Cisco TelePresence Touch controller. The first contact method ContactMethodId: The unique identifier for the contact method you want to modify. The identifier may have been created when issuing the xCommand Phonebook Contact Add command to make will be returned by an xCommand Phonebook Search command.
Set a menu password to restrict access to Administrator Settings menu. If you have a remote Second:0 control the password can also be set from the on screen menu. If you have a Cisco TelePresence *r DateTimeSetResult (status=OK): Touch controller the menu password is set from the command line interface.
Video PIP Presentation Set Sets position for the presentation PiP (picture in picture). The Experimental commands are for testing only and should not be used unless agreed with Cisco. Position: Predefined positions. These commands are not documented and WILL change in later releases.
Call [n] DeviceType Shows the duration of a call (in seconds). You can run the command xStatus Call to find the call Indicates whether the remote system is a single endpoint or a MCU. Some Cisco endpoints (EX90, identity.
Conference Site [n] Capabilities Presentation xStatus Conference Site [n] BlackScreenCause Lists the presentation capabilities for other participants in the conference. Shows the reason why the screen is black while in a CTMS (Cisco TelePresence Multipoint Switch) managed conference. Value space of the result returned: FirstParticipant: You are the first and only participant in the meeting.
Timeout: The attempt to establish communication to the SIP Proxy timed out. register to is included in the codec’s trusted CA-list. The server is typically a Cisco VCS or CUCM. UnableTCP: The system is unable to use TCP as the transport method.
Shows whether or not the SSL certificate of the server that the video system / codec tries to register to is included in the codec’s trusted CA-list. The server is typically a Cisco VCS or CUCM. True: The server’s SIP certificate is checked against the trusted CA-list on the codec and found xStatus SIP Profile 1 CallForward Mode valid.
Video PIP Presentation Position Shows the position of the presentation image on the screen. The Experimental status is for testing only and should not be used unless agreed with Cisco. These Value space of the result returned: settings are not documented and WILL change in later releases.
Button codes - Remote control 5 Button codes - Remote control 5 Address Button name Address Button name The Cisco TelePresence Remote Control 5 has the following button codes and IR signal parameters. Arrow left Number 1 Arrow right Number 2...
INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system.