Setting A Later End Time; Setting The Clock; Memory; Saving Settings In The Memory - Siemens HB78GB.90B Instruction Manual

Setting a later end time

Please remember that easily spoiled foods must not be allowed
to remain in the cooking compartment for too long.
A later end time can be set for
all types of heating
■
a variety of programmes
■
and for self-cleaning
■
Example: you put the dish in the cooking compartment at 9.30 .
It takes 45 minutes to cook and will be ready at 10.15, but you
would like it to be ready at 12.45 instead.
Change the end time from 10.15 to 12.45. The oven goes into
standby. Cooking starts at 12.00 and finishes at 12.45.
This function is also available for self-cleaning. You can shift the
time of the cleaning operation so it is carried out at night, which
means that the oven is available at all times during the day.
Setting a later end time
Prerequisite: The selected operation has not already begun and
0
a cooking time has already been set. The time-setting options
menu is open.
Move to the end time using the
1.
displayed.
7\SHV RI KHDWLQJ
Using the rotary selector, set a later end time.
2.
7\SHV RI KHDWLQJ
0
3. Press the button to close the time-setting options menu.
Confirm by pressing the
4.
The setting is adopted. The oven is in standby, the
is displayed in the status bar. Operation starts at the
appropriate time. You can see the
down in the status bar.

Memory

You can save the settings for a dish in the memory and call it
up again at any time.
The memory is useful for if you frequently prepare a specific
dish.

Saving settings in the memory

The self-cleaning function cannot be saved.
Specify the type of heating, temperature and, if required, a
1.
cooking time for the dish you wish to cook. Do not start. If
you want to save a programme: Select the programme and
make the settings. Do not start.
l
Press and hold the button until "Memory saved" is
2.
displayed.
The setting has been saved and can be started immediately.
12
¿
button. The end time is
 
 
†
button.
y
z
cooking time counting
The cooking time has elapsed
A signal sounds. The oven stops heating. The status bar shows
the cooking time as
by pressing the
Correcting the end time
This is possible, providing the oven is on standby. To do this,
¿ ¾
open the menu with the
the or button and adjust the end time using the rotary
selector. Press the
Cancelling the end time
This is possible, providing the oven is on standby. To do this,
¿ ¾
open the menu with the
the or button and turn the rotary selector anti-clockwise
until the display disappears. The cooking time immediately
starts to count down.

Setting the clock

The oven must be switched off before you can set or change
the clock.
Following a power cut
"Set clock" appears in the status bar following a power cut.
Turn the rotary selector to set the current time.
1.
The display language set is displayed in the settings area on
 
the right-hand side. This does not change following a power
cut.
0
2. Press the
The time is applied.
Changing the clock
Example: changing from summer to winter time.
0
 
Press the
1.
The time-setting options menu appears.
¿
Use the
2.
time using the rotary selector.
0
Press the
3.
The time-setting options menu closes.
Changing the clock display
end time
The clock appears in the display when the oven is switched off
and shows the current time. You can change the display to a
different clock appearance, to digital time or remove the clock
from the display. For more information, refer to the Basic
settings section.
Saving another setting
Enter and save the new setting. The old settings are
overwritten.

Starting the memory

You can start cooking at any time using the settings saved for
your dish.
l
Press the
1.
The saved settings are displayed. If "Memory location empty"
appears, no settings have been saved. You cannot start the
memory. Save the required setting first, as described under
Saving in the memory.
†
Press the
2.
The memory setting starts.
x
0
0:00. You can cancel the signal early
button.
0
button, move to the end time with
0
button to close the menu.
0
button, move to the end time using
button.
button.
0
button to move to the clock, then change the
button.
button briefly.
button.