Table of Contents
Advertisement
Recalling the Preset Memory
1
Check that Defeat mode is off.
2
Press SETUP.
The SETUP selection screen appears.
3
Touch [
] of i-Personalize.
The i-Personalize screen will appear.
4
Touch [ ] or [ ] of A.PROCESSOR to select the
preset memory you want to recall from P-1 through
P-6.
• It takes a few moment to recall the preset memory.
Using the Pro Logic II Mode
Pro Logic processing can be conducted on the music signals recorded
on two channels to achieve Dolby Pro Logic II surround sound. For
two-channel Dolby Digital and DTS signals, there is also a "REAR
FILL" function for outputting the signals of the front channel to the rear
channel.
1
Check that Defeat mode is off (pages 26, 27).
2
Press SETUP.
The SETUP selection screen appears.
3
Touch [
] of i-Personalize.
The i-Personalize screen will appear.
4
Touch [
] of A.PROCESSOR.
The A.PROC list screen appears.
5
Touch [
] of DOLBY PLII/REAR FILL.
The DOLBY PLII/REAR adjusting screen appears.
6
Touch [ ] or [ ] of DOLBY PLII/REAR to select the
desired mode.
PL II MOVIE: Suits the stereo TV shows and all programs
encoded in Dolby Surround. It improves the
sound field directivity to near that of discrete
5.1-channel sound.
PL II MUSIC: Can be used for all stereo music recordings, and
provides a wide, deep sound field.
OFF:
Turns DOLBY PL II function to OFF.
48
-EN
If PL II MUSIC is selected, the center width can be adjusted with
following operations.
This function offers the optimum vocal position by adjusting the
center channel position between the center speaker and the L/R
speaker. (The adjustments established in "Adjusting the
acoustic image (BI-PHANTOM)" (page 46) are ineffective while
this function is activated.)
Touch [ ] or [ ] of CENTER WIDTH CONT to adjust the
level.
The level can be adjusted between 0 to 7. When the level
increases, the center channel position moves from the
center speaker position to both sides.
Touch [OFF] of CENTER WIDTH CONT to turn off the
center width control.
• This adjustment is effective when the setting of the center speaker is
SMALL or LARGE in the speaker setup settings.
• "REAR FILL" function:
Depending on the input signals, the sound may only be output from
the front speakers. In this case, the "REAR FILL" function can be
used to output signals from the rear speakers as well.
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is cancelled if the Decode mode is switched.
• This adjustment is ineffective when the speaker is set to CENTER
OFF in "Setting the Speakers" (page 42).
• This function only works with two-channel signals. This operation is
ineffective when 5.1-channel DTS or Dolby Digital signals are input.
• If the setting of REAR FILL is made when REAR MIX is ON, sound is
unchanged in the rear fill setting because REAR MIX is given priority
during 2 channel decoder other than linear PCM.
• For linear PCM signals, the voice is output from the rear speaker
regardless of the REAR FILL and REAR MIX setting.
• Touching [RTN] will return to the previous screen.
Linear PCM Setting
The output when playing discs recorded in linear PCM can be set to 2 or
3 channels.
1
Check that Defeat mode is off.
2
Press SETUP.
The SETUP selection screen appears.
3
Touch [
] of i-Personalize.
The i-Personalize screen will appear.
4
Touch [
] of A.PROCESSOR.
The A.PROC list screen appears.
5
Touch [ ] or [ ] of PCM MODE to select 2 CH or 3
CH.
2CH: 2ch output (L/R)
3CH: 3ch output (L/R/CENTER)
• This adjustment is ineffective when the speaker is set to CENTER
OFF in "Setting the Speakers" (page 42).
Hide quick links:
Advertisement
Table of Contents
