Table of Contents
Advertisement
Quick Links
•
High quality of compression algorithm (H.264/MJPEG)
•
H.264 + H.264 / H.264 + MJPEG Dual Streaming
•
Encoder/Decoder selectable
•
Full-duplex audio/video transmission
•
30fps/25fps @ full D1 resolution
•
1:N Multi-casting and relayed data transmission
•
Protocols : TCP/IP, Multicast, HTTP, SMTP, SNMP, FTP, DHCP, DNS, Dynamic DNS,
RTP, RTSP
•
Real time monitoring/recording/playback through CMS viewer S/W and Internet
Explorer
•
Dynamic IP support with Dynamic DNS
•
Power over Ethernet(PoE) support
•
Data storage against network failure or event (USB2.0)
•
Watchdog for system recovery
•
Support for PTZ and Controller
•
Motion detection
VT-IPSD102H
Dual Streaming IP Server
with H.264 Compression
CYAN
MAGENTA
YELLOW
BLACK
Advertisement
Table of Contents
Related Manuals for Vitek VT-IPSD102H
Summary of Contents for Vitek VT-IPSD102H
- Page 1 VT-IPSD102H Dual Streaming IP Server with H.264 Compression • High quality of compression algorithm (H.264/MJPEG) • H.264 + H.264 / H.264 + MJPEG Dual Streaming • Encoder/Decoder selectable • Full-duplex audio/video transmission • 30fps/25fps @ full D1 resolution • 1:N Multi-casting and relayed data transmission •...
- Page 2 VT-IPSD102H Manual Safety Precaution Make sure to turn off the power before installing the VT-IPSD102H. Do not install under direct sunlight or in dusty areas. Make sure to use the product within the temperature and humidity that is specified.
-
Page 3: Table Of Contents
VT-IPSD102H Manual Table of Content Table of Content ............................2 1. Introduction ............................4 1. About User Manual ........................4 2. Feature ............................4 3. Product and Accessories ......................6 4. Part Names and Description ......................7 5. System Modes and Connections ....................9 2. - Page 4 VT-IPSD102H Manual 4. Server Status Monitoring ......................44 5. Network and System Diagnostics ....................45 6. F/W Upgrade ..........................48 7. Remove Configuration and Video Monitoring ................49 6. Trouble Shooting ..........................49 Appendix A: Sensor and Alarm Port ...................... 50 1.
-
Page 5: Introduction
VT-IPSD102H as well as how to troubleshoot. 2. Feature VT-IPSD102H is a video and audio surveillance transmission system based on IP network through LAN, ADSL/VDSL, and Wireless LAN. The VT-IPSD102H series operates as one of two modes: Encoder or Decoder. The Encoder system compresses and transmits video data. Decoder receives and decompresses the video data. - Page 6 VT-IPSD102H Manual USB Connection to internal or external USB storage for remote access User Interface System status display utilizing OSD (On Screen Display) Diagnose and upgrade through dedicated program called ENVI VMS System configuration using Internet Explorer High Reliability...
-
Page 7: Product And Accessories
VT-IPSD102H Manual 3. Product and Accessories VT-IPSD102H Quick Manual Power adaptor and cable User Manual & S/W CD Screws Brackets <Picture 1> Product and Accessories... -
Page 8: Part Names And Description
VT-IPSD102H Manual 4. Part Names and Description Front View Parts Function LEDs Display power On/Off condition, Link, Status and Data Audio In, Out Audio Input and Output USB USB port for any USB device ... - Page 9 VT-IPSD102H Manual Rear View Terminal Function POWER IN DC 12V power input SENSOR Sensor input ALARM Relay output RS-422/485 Serial port 2 (COM2) for PTZ control and etc. Support RS-422 and...
-
Page 10: System Modes And Connections
VT-IPSD102H Manual 5. System Modes and Connections The VT-IPSD102H system operates in one of two modes: Encoder or Decoder. The VT-IPSD102H system can be connected in either a ‘1-to-1’ fashion, where one encoder is connected to one decoder, or a ‘1-to-many’ fashion, where one encoder is connected to many decoders. - Page 11 VT-IPSD102H Manual 1:N Connection (Unidirection) Remote Center Site Decoder Encoder Decoder Decoder In this configuration, a site can be monitored from many remote center locations. Although up to 64 decoders can be connected to on encoder, in the real network environment, network bandwidth can limit the maximum connections.
- Page 12 VT-IPSD102H Manual VMS (Video Management System) Site Remote Center Encoder Site Remote Center Encoder Decoder VMS SW is a Windows based remote monitoring program to access multiple encoders for real-time monitoring or control of the encoders and connected cameras. Please refer to VMS User Manual for more information on VMS.
-
Page 13: Installation
2. Installation 1. Connecting Video Encoder System Connect the camera video output line to the encoder VT-IPSD102H video input port. Decoder System Connect the monitor video input line to the decoder VT-IPSD102H video output port. 2. Connecting Audio Audio is bi-directional in any configuration regardless of the system mode. -
Page 14: Checking Operating
VT-IPSD102H Manual 6. Checking Operating Once the power is supplied to the camera, it will start booting. The system will boot up to an operating mode after approximately 40-60 seconds. The green LED on the Ethernet port will flash indicating the system is ready. -
Page 15: System Operation
VT-IPSD102H Manual 3. System Operation 1. LED Display Description of LEDs System status can be monitored with LEDs. State Description No power Power on Green blinking Normally operating System failure: Needs diagnostics Constant change of colors NTSC/PAL setting does not match with input... -
Page 16: Remote Video Monitoring
Video Monitoring using Internet Explorer If the VT-IPSD102H’s IP address is entered in Internet Explorer, the system will ask for confirmation to install Active-X control. Once authorized, Internet Explorer will start to display video images from the encoder as shown below. -
Page 17: Initialization Of Ip Address
Focus Near, Focus Far, Auto Focus Adjust the focus Sensor Input When the sensor on the VT-IPSD102H is connected and working, the light turns red. Alarm Output Alarm Output button can trigger an event directly from the Live View page. -
Page 18: Remote Configuration
4. Remote Configuration 1. Remote Configuration The server can be configured using a web browser. Type the IP address of VT-IPSD102H in the address input area of Internet Explorer, then a live viewing screen will be displayed. Press Setup button located in the upper right area of the monitoring screen, then the server setup page will be displayed. -
Page 19: System Configuration
VT-IPSD102H Manual 2.1 System Configuration System Mode System mode: Select Encoder, Decoder System ID System ID: Alphanumeric System ID to be transferred to remote software Language Language to be used for web-based configuration Firmware version Current firmware version... - Page 20 VT-IPSD102H Manual Board ID Network board ID of VT-IPSD102H recognized by system Start Time Latest system boot date and time Current Time Current date & time: Enter a new date and time and press Set Current Time button to update date &...
-
Page 21: Video Configuration
VT-IPSD102H Manual 2.2 Video Configuration -20-... - Page 22 VT-IPSD102H Manual - ENCODE Input Format Select input format; Composite NTSC or PAL Resolution Selectable video compression resolution as below: NTSC: 720 x 480, 720x 240, 352 x 480, 352 x 240 PAL: 720 x 576, 720 x 288, 352 x 576, 352 x 288 ...
- Page 23 VT-IPSD102H Manual - DUAL ENCODE Use Dual Encode Select On to use dual encode Dual Encode Algorithm H.264 and MJPEG can be selected for secondary streaming. Maximum resolution is 720 x 480 and there are 8 steps of resolution. If MJPEG is selected, Preference supports only Quality mode.
- Page 24 VT-IPSD102H Manual Information Display System ID and/or server time can be displayed over the video window in Web View. Each item can be turn on or off and position can be configured as well. This information is displayed after the video is decompressed.
-
Page 25: Audio Configuration
Bit rate: Select the Bit rate between 64kbps and 128kbps when AAC is selected The sampling rate is fixed to 32KHz when AAC is selected. Note that when VT-IPSD102H is connected to a decoder, the decoder’s audio algorithm should be set identically to transmit audio properly. -
Page 26: Network Configuration
VT-IPSD102H Manual 2.4 Network Configuration -25-... - Page 27 RTSP port used for RTSP-based connection SNMP VT-IPSD102H can be used as an SNMP agent. It is compatible to both SNMPv1 and SNMPv2c. Vender specific MIBs for IP camera/server are defined. SNMP listen port can be set and disabled when it is 0. SNMP trap is also supported. Destination IP and port can be set.
- Page 28 VT-IPSD102H Manual Address Information Tree addresses are checked by 3 ways below. (Read-only) IP Address The servers own IP address. This information is useful when the server’s IP mode is set to DHCP. Domain Name In case the server is registered with a DDNS server, the registered domain name is displayed.
-
Page 29: Serial Port Configuration
VT-IPSD102H Manual 2.5 Serial Port Configuration -28-... - Page 30 VT-IPSD102H Manual Serial Port Configuration There are two serial ports, (COM1 and COM2) in VT-IPSD102H. While COM1 port is fixed to RS-232C, COM2 port can be set to RS-422 or RS-485 protocol. The serial ports can be configured as follows.
-
Page 31: Event Configuration
VT-IPSD102H Manual 2.6 Event Configuration -30-... - Page 32 VT-IPSD102H Manual The event configuration configures the actions for each event type. Local section configures the actions for events from local (self) system, and configuration activates local devices and a Remote section configures the actions for events from remote (peer) system.
- Page 33 VT-IPSD102H Manual E-mail Notification Specify the information to send E-mail as the action of an event. The address of mail (SMTP) server needs to be specified in the Server Address field, and Port specifies the port for SMTP operation (Port 25 is the default port in SMTP operation. If a different port is configured in the SMTP server, this port needs to be changed accordingly).
-
Page 34: Preset Configuration
VT-IPSD102H Manual 2.7 Preset Configuration Preset Name Move PTZ Camera to normal view Save Press Set Button Configure up to 15 preset positions. Preset function is not available on some PTZ receivers. Make sure to check if a PTZ receiver supports preset. -
Page 35: User Configuration
VT-IPSD102H Manual 2.8 User Configuration User can be registered and privilege level of a user can be specified. User configuration is allowed only to admin user. Max 16 users can be registered and each user can have one of four privileges. - Page 36 VT-IPSD102H Manual Delete User A user is deleted by pressing Delete button. Change Password Pressing the Modify Password button after selecting a user shows a page for changing password. If changing the admin password, the old password is checked first.
-
Page 37: Decoder System
Once system mode is changed as decoder, Firmware version shows Dec xxxxxxx which means decoder mode. 3.1 Video Configuration Regardless of the input resolution of the Encoder or IP camera, Decoder system of VT-IPSD102H can display video format as follows; Composite NTSC & HDMI 480i (720 x 480) Composite PAL &... -
Page 38: Network Configuration
VT-IPSD102H Manual 3.2 Network Configuration Network page of Decoder has a section for specifying the remote system to connect. -37-... - Page 39 VT-IPSD102H Manual Remote Address Address of the remote system to connect. Remote Channel The channel can be selected when the remote system has more than one video channels. Media Protocol Protocol used for delivery of audio and video data between remote system and Decoder.
-
Page 40: Event Configuration
VT-IPSD102H Manual 3.3 Event Configuration The event configuration configures the actions for each event type. The Local section configures the actions for local events (self=Decoder) system, and configuration activates local devices and Remote sections configures the actions for events from remote (Encoder or IP Camera) system. - Page 41 VT-IPSD102H Manual The following table lists the possible actions for events. Action Description Outputs beep sound using the buzzer in the Beep system Alarm1/Alarm2 Triggers alarm (relay) port Sends E-mail to the specified address. AVI file E-mail can be attached...
-
Page 42: Envi Visual Management Software (Vms)
VT-IPSD102H Manual 5. ENVI Visual Management Software (VMS) 1. ENVI Visual Management Software ENVI VMS is a program used for basic configuration, diagnostics and F/W upgrades of video servers or IP cameras. ENVI VMS provides the following features: - Finding servers on the LAN and assigning IP address - Monitoring server status: encoding/decoding, serial, sensor etc. - Page 43 VT-IPSD102H Manual Press Add button. Removal of a server A server can be removed with the following steps: Select the server to remove on Servers tab; the selected server is highlighted in blue. Select Remove Server on the Server menu.
-
Page 44: Server Connection Management
VT-IPSD102H Manual a dialog box where the IP address of the server can be changed. It is possible to change the IP address of a server which has an IP address of a different subnet. Grouping of servers When there are a large number of servers, it is convenient to manage servers in several groups. -
Page 45: Server Status Monitoring
VT-IPSD102H Manual 4. Server Status Monitoring Servers tab – General information Servers tab shows general information for a connected server: MAC address, product model, system mode (Type) F/W version and startup time. This information comes only for connected servers. -
Page 46: Network And System Diagnostics
VT-IPSD102H Manual Item Displays COM1-TX Activity of RS-232C port COM1-RX - TX: server -> external equipment - RX: external equipment -> server COM2-TX Activity of RS-422/485 port COM2-RX - TX: server -> external equipment - RX: external equipment -> server... - Page 47 VT-IPSD102H Manual Ping test is useful for checking if one or more remote systems are reachable from a server. Up to 4 systems can be registered as the targets of a Ping test, which makes it possible to identify the hop (segment of network) where network failure may happen.
- Page 48 VT-IPSD102H Manual System Check System Check tests if H/W components are fine and displays board ID and MAC address. Video Out Check / Display Color Bar It displays color bar on video output port. This function works for Decoder or Duplex mode, and is useful for checking if video output port or external display device is normal.
-
Page 49: F/W Upgrade
VT-IPSD102H Manual Remote rebooting of a server A server can be rebooted by selecting Reboot in the Tools menu. 6. F/W Upgrade When Update is selected on the Tools menu, the dialog for F/W upgrade appears. Select a server to upgrade (check the check box in Sel column). More than one server can be upgraded simultaneously. -
Page 50: Remove Configuration And Video Monitoring
VT-IPSD102H Manual Caution: Don’t power-off the server while upgrade is in progress. The server may go to irrecoverable state. When the network condition is poor, the upgrade may fail. In such case, please reattempt the procedure above after the network condition is recovered. -
Page 51: Appendix A: Sensor And Alarm Port
VT-IPSD102H Manual Appendix A: Sensor and Alarm Port 1. Sensor Port Terminal Type * Voltage Rating: 150VAC * Current Rating: 2A * Color: Red Sensor Signal Input Type * NO Contact Signals Connection to External Device 2. Alarm Port ... -
Page 52: Appendix B: Serial Port
VT-IPSD102H Manual Appendix B: Serial Port 1. RS-232 Port Port Type * 3 PIN * Pin Arrangement * Pin Description Pin NO Pin Name Description RS232 TX (Transmit) RS232 RX (Receive) Ground 2. RS-422/485 Port Port Type -51-... - Page 53 VT-IPSD102H Manual * 4 PIN * Pin Diagram * Pin Description Pin No. Pin Name Description RS422 RX- RS422 RX+ RS422 TX- or RS485 TRX- It is selectable by S/W Setup RS422 TX+ or RS485 TRX+ It is selectable by S/W Setup...
- Page 54 (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is non-transferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller.
- Page 55 28492 CONSTELLATION ROAD VALENCIA, CA 91355 WWW.VITEKCCTV.COM | 888-VITEK-70...