Installation - Kenmore 580.73083 Owner's Manual

INSTALLATION
We strongly recommend the removal of the
old wall sleeve and the installation of a new
Kenmore Wall Sleeve.
If you decideto keepthe existing wall sleeve,
you have to redirectthe louversat the backof the
wall sleeveillustration. The use of pliers is
recommended. If you DO NOT redirect,you run
the riskof poorperformanceor productfailure.
This is notcoveredunderthe termsof the
Kenmorewarranty.
• Pick a location which will allow the conditioned air
to blow into the area you want. Good installation
with special attention to the proper position of the
unit will lessen the chance that service will be
needed.
ITEMS IN INSTALLATION HARDWARE
You may not need all parts in the kit. Discard
unused pads
ITEM (inches)
Plastic grille 263/4x 161/2
I
Horizontal Insulation Stripe113/8 x s/8x 273/16
13/8 X 13/8 X 273/16
Around Insulation Strips 13/8x 3/4x 611/2
1% x 1% x 611/2
Support Block 13/4x 1% x 451m
Baffle 14 x 41/2x 1/8
Shim 13x lx3/4
Trim Frame
Washer Screw
Nuts(Plastic)
Qty.
1
1
1
1
1
2
1
2
2
4
4
HOW TO INSTALL
li]l Identify the existing wall sleeve before installing
the unit from the listed below.
Brand
White-Westinghous_
Frigidaire
Carrier (52F series)
General Electric
/Hotpoint
Whirlpool
Fedders/Emerson
Sears/Kenmore
Emerson/Fedders
Carrier (51S Series)
Friedrich
Wall Sleeve Dimensions (inches _,
Width Height Depth
25-1/2 15-1/4 16, 17-1/2
or 22
26 15-5/8 16-7/8
17-1/8
25-7/8 16-1/2
or 23
27 16-3/4 16-3/4
or 19-3/4
25-7/8 15-17/32 16-23/32
26-3/4 15-3/4 15
25-3/4 16-7/8 18-5/8
27 16-3/4 16-3/4
NOTE: All wall sleeves used to mount the new Air
Conditioner must be in sound structural condition
and have a rear grille that securely attaches to
sleeve, or rear flange that serves as a stop for the
Air Conditioner,
[]Remove old air conditioner from existing wall
sleeve.
_1 Clean the interior of an existing sleeve.
(Do not disturb seals.)
Q Wall sleeve must be securely fastened in wall
before installing the air conditioner. Use the
nails or screws through sleeve into wall, if
needed. Repaint sleeve if needed.
!_ Prepare the wall sleeve for installation of the
unit. If you plan to use your existing wall sleeve,
and it is not Kenmore, use procedure B or C
below.
Procedure
A
Brand
Sears/Kenmore
White-Westinghouse
Frigidaire Carrier
(52F series)
General Electric
/Hotpoint
Whirlpool
Carrier (51S series)
Depth(inches)
16-23/32
16, 17-1/2
or 22
16-7/8
Fedders/Emerson
C
Emerson/Fedders
Friedrich
_r_ Install new unit into wall sleeve.
CAUTION: When installation is completed,
replacement unit MUST have a rearward slope as
shown.
17-1/8 or 23
18-5/8
16-3/4
or 19-3/4
15
16-3/4
UNIT Wall Sleeve
FRONT"_ 1- -_ ............. i
114" i _ ............. i
FIG. 3
-6-