Inquiries - Cisco TelePresence PrecisionHD 1080P 12x User Manual

Cisco TelePresence PrecisionHD Camera
Contents Introduction
The VISCA™/RS–232 control protocol, cont...

Inquiries

Command Command
Packet
CAM_ID_Inq 8x 09 04 22 ff
CAM_SWID_Inq 8x 09 04 23 ff
CAM_HWID_Inq 8x 09 04 24 ff
Zoom_Pos_Inq 8x 09 04 47 ff
Focus_Pos_Inq 8x 09 04 48 ff
Focus_Mode_Inq 8x 09 04 38 ff
PanTilt_Pos_Inq 8x 09 06 12 ff
Power_Inq 8x 09 04 00 ff
WB_Mode_Inq 8x 09 04 35 ff
WB_Table_Inq 8x 09 04 75 ff
AE_Mode_Inq 8x 09 04 39 ff
Backlight_Mode_ 8x 09 04 33 ff
Inq
Mirror_Inq 8x 09 04 61 ff
Flip_Inq 8x 09 04 66 ff
D14640.03 PrecisionHD 1080p-720p Camera User Guide TC4.0, November 2010.
© 2010 Cisco Systems, Inc. All rights reserved.
The physical interface Connecting the camera
Response
Resp: 90 50 zz xx 00 yy ff
Only zz, which identifies the camera, is
relevant. zz = 0x50 for this camera.
Resp: y0 50 [1-125 bytes ASCII SWID] ff. Never
route this message through Sony cameras.
The response is the Module Serial Number
stored in EEPROM. The number is converted
to ASCII : y0 50 [12 bytes ASCII HWID] ff.
Resp: y0 50 0p 0q 0r 0s ff
pqrs: zoom position
Resp: y0 50 0p 0q 0r 0s ff
pqrs: focus position
Resp: y0 50 0p ff
p=2: Auto, p=3: Manual
Resp: y0 50 0p 0q 0r 0s 0t 0u 0v 0w ff
pqrs: pan position tuvw:
tilt position
Resp: y0 50 0p ff
p=2: On, p=3: Off
Resp: y0 50 0p ff
p=0: Auto , p=6: Table manual
Resp: y0 50 0p 0q 0r 0s ff
pqrs: Table used if table mode
Resp: y0 50 0p ff
p=0: Auto, p=3: Manual
Resp: y0 50 0p ff
p=2: On, p=3: Off
Resp: y0 50 0p ff
p=2: On, p=3: Off
Is video flipped or not?
Resp: y0 50 0p ff
p=2: On , p=3: Off
Video output formats
INFO: Some VISCA™ commands do not apply to the PrecisionHD 1080p 4X camera.
Command Command
Packet
Gamma_Mode_Inq 8x 09 04 51 ff
Gamma_Table_Inq 8x 09 04 52 ff
Call_LED_Inq 8x 09 01 33 01 ff
Power_LED_Inq 8x 09 01 33 02 ff
Video_System_Inq 8x 09 06 23 ff
DIP_Switch_Inq * 8x 09 06 24 ff
IR_Output_Inq 8x 09 06 08 ff
ALS_RGain_Inq * 8x 09 50 50 ff
ALS_BGain_Inq * 8x 09 50 51 ff
*
ALS_GGain_Inq 8x 09 50 52 ff
ALS_WGain_Inq * 8x 09 50 53 ff
Up side down_Inq * 8x 09 50 70 ff
*
Do not apply to PrecisionHD 4X camera
24
PrecisionHD Camera User guide
Daisy chaning Appendices Appendices
Response
Resp: y0 50 0p ff
p=2: Auto, p=3: Manual
Resp: y0 50 0p 0q 0r 0s ff
pqrs: Gamma table in use if manual mode.
Resp: y0 50 0p ff
p=2: On, p=3: Off, p=4: Blink
Resp: y0 50 0p ff
p=2: On, p=3: Off
y0 50 0p 0q 0r 0s ff
pqrs=video mode currently being output on
the HDMI port. See chapter on DIP switches.
y0 50 0p 0q 0r 0s ff pqrs contains the bit
pattern of the DIP switch. See chapter on DIP
switches.
Resp: y0 50 0p ff
p=2: On, p=3: Off
Ambient Light Sensor Resp: y0 50 0p 0q 0r 0s
0t 0u 0v 0w ff
pqrstuv=32 bit unsigned integer, relative gain
value. The integration time is a constant set in
the camera SW.
Resp: y0 50 0p ff
p=0: Camera is upright.
p=1: Camera is upside down.
www.cisco.com