JVC DT-V9L5 Instructions Manual page 33

Setting for the picture quality.
Item To do
Backlight Adjusts the brightness of the display.
Aperture* 1 Activates/deactivates the function at the level set in "Aperture Level".
Aperture Level* 1 Compensate the frequency response of the luminance signal of the video signal.
CTI Adjust the clearness of the outlines of the chrominance signal.
LTI Adjust the clearness of the outlines of the luminance signal.
Gamma Select the Gamma correction value. 2.2 is equivalent to Υ 2.2, 2.35 is equivalent to Υ 2.35,
2.45 is equivalent to Υ 2.45, 2.6 is equivalent to Υ 2.6.
Color Temperature Select the color temperature.
sub menu Display the sub menu which enables you to adjust the items in "Picture Function" while viewing the actual picture.
reset Restore the default settings for all the items in "Picture Function".
* 1 Memorized for each input.
Adjusts the size and position of the picture.
Item To do
H Size* 1 Adjust the horizontal picture size.
H Position* 1 Adjust the horizontal picture position.
V Size* 1 Adjust the vertical picture size.
V Position* 1 Adjust the vertical picture position.
sub menu Display the sub menu which enables you to adjust the items in "Size/Position Adjust" while viewing the actual picture.
reset Restore the default settings for all the items in "Size/Position Adjust".
* 1 Memorized for each signal format.
Sets the aspect ratio of the screen for displaying videos.
Item To do
Auto Aspect Select whether to adjust the aspect ratio (horizontal to vertical ratio of the screen) of the SD
signal automatically or manually (Manual Aspect).
Manual Aspect* 1 Sets the aspect ratio (horizontal to vertical ratio of the screen) of the SD signal.
SD4:3 Size* * Selects the picture size when the input signal format is 4:3.
1, 2
Normal
H Full
V Full
16:9 Size* 1, * 2 Selects the picture size when the input signal format is 16:9.
Normal
V Full
1:1* 3 Displays the picture in the original resolution of the input signal.
The aspect ratio of the picture may change depending on the input signal.
When the picture is overscanned, markers are displayed at the top, bottom, left and right.
* 1 Not activate when picture is displayed in the 1:1 mode.
* When the histogram, wave form monitor or vector scope is displayed, only "Normal" is available.
2
* 3 When the histogram, wave form monitor or vector scope is displayed, only "Off" is available.
Setting values: Off, On
Adjusts the picture to be suitable for a bright place.
When the function is turned on:
- "Backlight" and "Picture Sub Adjust" are grayed out and cannot be operated.
- The setting of "Backlight" is ineffective.
Settings for displaying the range of brightness.
Item To do
Zebra Mode
Activate / deactivate the function.
H-Level Threshold Setting the maximum brightness of an image for Zebra. "Over" means the range which exceeds 100%. 5% to 100% (by 5%), Over
L-Level Threshold Setting the minimum brightness of an image for Zebra.
: Matches the vertical picture size to the number of pixels.
: Matches the horizontal picture size to the horizontal size of the screen. At
this time, the top and bottom of the picture are overscanned.
: Enlarges the picture vertically.
: Matches the vertical picture size to the number of pixels.
: Enlarges the picture vertically. At this time, the right and left of the
picture are overscanned and markers are displayed.
Setting value
–20 to +20
Off, On
01 to 10
Off, Normal, Hard
Off, Normal, Hard
2.2, 2.35, 2.45, 2.6
9300K, 6500K, User
Setting value
Setting value varies
depending on the signals.
Setting value
Off, On
16:9, 4:3
Normal, H Full, V Full
Normal, V Full
Off, On
Setting value
Off, On
0% to 100% (by 5%)
33 33