Table of Contents
Advertisement
Quick Links
DT-V9L3DY
MULTI FORMAT LCD MONITOR
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock. Do
not remove cover (or back). No user
serviceable parts inside. Refer servicing
to qualified service personnel.
The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the presence
of uninsulated "dangerous voltage"
within the product's enclosure that may
be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
INSTRUCTIONS
Table of Contents
Safety Precautions .............................................. 2
IMPORTANT SAFEGUARDS ........................... 2
Installation ............................................................ 4
To adjust the stand height ................................ 4
Daily Operations / Connections ......................... 6
Front panel ....................................................... 6
Rear panel ........................................................ 8
Available signals ............................................... 9
Menu Configuration-MAIN MENU .................. 10
Menu Configuration-SET-UP MENU ............... 14
External Control ................................................. 16
About the external control .............................. 16
Using the MAKE/TRIGGER system ............... 16
Using the RS-232C system ............................ 17
Troubleshooting ................................................. 18
Self-check program ........................................ 19
Maintenance ....................................................... 20
Specifications .................................................... 21
General ........................................................... 21
Input/output terminals ..................................... 21
Dimensions ..................................................... 22
LCT2530-001A-H
Advertisement
Table of Contents
Related Manuals for JVC DT-V9L3DY - Broadcast Studio Monitor
Summary of Contents for JVC DT-V9L3DY - Broadcast Studio Monitor
-
Page 1: Table Of Contents
The lightning flash with arrowhead symbol, within an equilateral triangle is CAUTION intended to alert the user to the presence of uninsulated “dangerous voltage” RISK OF ELECTRICAL SHOCK within the product’s enclosure that may DO NOT OPEN be of sufficient magnitude to constitute a risk of electric shock to persons. -
Page 2: Safety Precautions
Safety Precautions WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO Under the following conditions, • The AC power supply is controlled by turning on/ RAIN OR MOISTURE. NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE 1. -
Page 3: Important Safety Instructions
A grounding type plug has two blades and a third grounding prong. The wide blade or the CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for equipment. -
Page 4: Installation
Installation CAUTION Higher position • Do not rest your arm on the monitor or lean against the monitor. • Do not touch the LCD panel when installing the monitor. • Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury. - Page 5 Lower position To prevent an accidental fall Fix the monitor to a wall by using strings. Attachment screws Fixing the monitor Attach the hook (not provided) to the VESA mounting holes on the rear panel (use the two 100 mm pitch holes on the upper side) using M4 x 10 mm screws (not provided).
-
Page 6: Daily Operations / Connections
Daily Operations / Connections 7 Front panel • “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp Tally lamp lights even when the function does not actually work). This lamp is controlled by the tally function of the MAKE/TRIGGER terminal. - Page 7 Menu Operations Audio Channel Selection On the Information Display On the Status Display Select audio channels emitted from the speaker The monitor displays the information below If you press the input button of the current input, Display the menu. and the AUDIO (MONITOR OUT) OUT1/OUT2 depending on the settings of the menu.
-
Page 8: Rear Panel
Daily Operations / Connections (cont.) 7 Rear panel 5 VIDEO/COMPONENT terminals (BNC) p REMOTE terminals IN: Input terminals for the composite (VBS) and the Terminals for controlling the monitor by an external analog component (Y/P ) signals. control. (☞ “External Control” on page 16) •... -
Page 9: Available Signals
7 Available signals Attaching the Power Cord Holder The following signals are available for this monitor. The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN terminal. Video signals • The power cord holder consists of two parts, a case and a cover. Input terminal Signal format shown VIDEO/COMPONENT... -
Page 10: Menu Configuration-Main Menu
Menu Configuration—MAIN MENU For the operation procedure, see page 7. PICTURE IMPROVEMENT Setting for the picture quality Item To do Setting value APERTURE* Select the frequency of the luminance signal compensated in OFF, LOW, HIGH “APERTURE LEVEL.” APERTURE Compensate the frequency response of the luminance signal of the 01 –... - Page 11 MARKER* Settings for marker functions Item To do Setting value ☞ “NOTE” AREA MARKER* Activate/deactivate the area marker and select the style of it. MARKER ASPECT* Select the aspect ratio of the area marker. 4:3, 14:9, 13:9, 2.35:1, 1.85:1, 1.66:1 ☞...
- Page 12 Menu Configuration—MAIN MENU (cont.) AUDIO SETTING Settings for the level meter Item To do Setting value BAR POSITION Select the type of the level meter display VERT. (vertically), HORZ. (horizontally) — vertically or horizontally. LEVEL METER ch Select the number of the audio channels OFF, 12CH, 8CH displayed on the level meter.
- Page 13 WAVE FORM SETTING Settings for the wave form monitor Item To do Setting value POSITION Select the position of the wave form monitor. 1 (lower right), 2 (lower left), 3 (upper left), 4 (upper right) GAIN Adjust the gain level for the incoming wave form –10 –...
-
Page 14: Menu Configuration-Set-Up Menu
Menu Configuration—SET-UP MENU FUNCTION SETTING For the operation procedure, see page 7. Settings for the sub menu display, color system, color of the tally lamp, and the format indicator. Item To do Setting value ☞ “NOTE” sub menu POSI. Select the contents and displaying position of “sub menu.” COLOR Select the color system. - Page 15 REMOTE SETTING (☞ “External Control” on pages 16, 17) Settings for the external control Item To do Setting value TYPE SEL. Select the external control method for the MAKE/ MAKE, TRIGGER, SET TRIGGER terminal. PIN1, PIN2, PIN3, Assign the control functions to the pins of the MAKE/ TALLY SEL, SDI 1, SDI 2, VIDEO/ PIN4, PIN5 TRIGGER terminal.
-
Page 16: External Control
External Control 7 About the external control Functions controlled by the MAKE/TRIGGER system Display Functions to be controlled Opening Short-circuiting This monitor has two external control terminals. TALLY SEL Selects the color of the tally lamp. Green • MAKE/TRIGGER terminal (RJ-45): The following external control systems are available. SDI 1 Changes the input to “SDI 1.”... -
Page 17: Using The Rs-232C System
Operation of the external control <Basic command list> Commands Functions Data Set “TYPE SEL.” of “REMOTE SETTING” to “MAKE” or “TRIGGER” in the SET-UP MENU. Short-circuit the 7th pin terminal (ENABLE) to the 8th pin terminal (GND) so that the monitor can be controlled 0 0 B C N 1 Cr Starts communication (connection) No data... -
Page 18: Troubleshooting
Troubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult an authorized dealer or service center. Symptom Probable cause and corrective action Page Symptom Probable cause and corrective action Page... -
Page 19: Self-Check Program
7 Self-check program This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes troubleshooting easier. Whenever a problem occurs, one or some of the self-check lamps will flash. If this happens, follow the steps below and contact your dealer to resolve the problem. When the screen goes blank and one or some of the self-check lamps on the front control panel start flashing... -
Page 20: Maintenance
Maintenance Unplug this product from the wall outlet before cleaning. Screen To avoid irreparable change in appearance of the screen such as uneven color, discoloration, scratches, be careful about the following: • Do not paste or stick anything using any glues or adhesive tapes. •... -
Page 21: Specifications
AC power cord x 1, Power cord holder x 1, Screw x 2 (for power cord holder), Accessories Never use any packing material supplied from sources other than JVC or JVC-authorized dealers. Protective filter x 1, Screw (for protective filter) x 4 •... -
Page 22: Dimensions
Specifications (cont.) 7 Dimensions Unit: mm (inch) <Front view> <Side view> <Rear view> • When the stand is attached to the • When the stand is attached to the higher position. lower position. 116 (4 5/8) VESA mounting holes 27.5 (1 1/8) (8-M4, depth: 10 mm) 1.5 (1/16) 222.4 (8 7/8) - Page 23 DT-V9L3DY MULTI FORMAT LCD MONITOR © 2009 Victor Company of Japan, Limited 0809TKH-MW-MT...