Summary of Contents for JVC DT-V2000SU - Dtv Monitor
Page 1
MONITOR DT-V2000SU INSTRUCTIONS For Customer Use: Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference. PHASE CHROMA BRIGHT CONTRAST MENU VOLUME/ENTER SELECT INPUT SELECT Model No. DT-V2000SU DT-V2000SU POWER Serial No.
Thank you for purchasing this JVC DTV monitor. Before using it, read and follow all instructions carefully to take full advantage of the monitor’s capabilities. SAFETY PRECAUTIONS WARNING : FCC INFORMATION CAUTION: Changes or modification not approved by TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT JVC could void the user’s authority to operate...
CONTENTS SAFETY PRECAUTIONS ....................2 CONTROLS AND FEATURES ..................4 CONNECTIONS ......................7 HOW TO HANDLE BASIC OPERATIONS ..............8 HOW TO PERFORM MAIN MENU ADJUSTMENTS ........... 10 HOW TO PERFORM SET-UP MENU ADJUSTMENTS ..........16 TROUBLESHOOTING ....................20 SPECIFICATIONS ......................22...
CONTROLS AND FEATURES FRONT VIEW <Front Panel> PHASE CHROMA BRIGHT CONTRAST MENU VOLUME/ENTER SELECT INPUT SELECT DT-V2000SU POWER PHASE CHROMA BRIGHT CONTRAST DT-V2000SU MENU VOLUME/ENTER SELECT INPUT SELECT POWER Speaker INPUT SELECT buttons A built-in speaker is located in the right panel when the Select the video signal input to each terminal.
REAR VIEW <Rear Panel> INPUT A INPUT B (RGB/COMPO.) (VIDEO) INPUT A INPUT B REMOTE IN/OUT (RGB/COMPO.) (VIDEO) INPUT C REMOTE IN/OUT INPUT C (RGB) (RGB) /B-Y /B-Y AC INPUT AUDIO INPUT AC INPUT /R-Y EXT SYNC (MONO) AUDIO INPUT /R-Y EXT SYNC (MONO)
Page 6
CONTROLS AND FEATURES (cont’d.) Notes: REMOTE IN/OUT terminal External control input and output terminal. Instead of ● To test external control, short-circuit the REMOTE using the INPUT SELECT button, an external control ENABLE terminal (Pin No. 1) to the GND terminal (Pin signal changes the INPUT mode.
CONNECTIONS Notes: ● Before connecting your system, make sure that all units are turned off. ● The illustration below shows some examples of different connections. Terminal connections may differ depending on the component(s) connected. Be sure to refer to the instructions provided with the unit(s) you are connecting. BASIC CONNECTION EXAMPLE Bridge output of Unit outputting Y/C...
HOW TO HANDLE BASIC OPERATIONS BASIC OPERATION 1. Press the POWER switch to Selected Input Display (Mode) POWER turn on the power. Display Input ON (_) : Power turns ON. (Power indicator lights in INPUT A (RGB) RGB input green.) INPUT A (COMPO.) COMPONENT input OFF (—) : Power turns OFF.
Page 9
OPERATION OF PICTURE ADJUSTMENT KNOBS PHASE knob Notes: Adjusts picture hue. ● The standard position of each knob is the center point where the knob clicks into place. PHASE greenish reddish The standard position is also indicated in the <PICTURE ADJ.>...
HOW TO PERFORM MAIN MENU ADJUSTMENTS • H SIZE: adjusts the horizontal screen size ADJUSTMENT OF SCREEN SIZE • H POSITION: adjusts the horizontal screen position • V SIZE: adjusts the vertical screen size AND SCREEN POSITION • V POSITION: adjusts the vertical screen position You can adjust the screen size and screen position.
• PINCUSHION: adjusts the pincushion distortion PICTURE DISTORTION • PIN. BALANCE: adjusts the balance of the pincushion distortion • PARALLELOGRAM: adjusts the parallelogram distortion ADJUSTMENT • TRAPEZOID: adjusts the trapezoid distortion You can adjust the picture distortion. SELECTING [ sub menu] IN PROCEDURE 4 This function can be set when an INPUT A component (COMPO.) You can also adjust items in procedure 5 with only the signal or INPUT B (VIDEO) signal is input with the underscan size...
HOW TO PERFORM MAIN MENU ADJUSTMENTS (cont’d.) PICTURE ADJUSTMENT You can adjust the picture contrast, brightness, etc. SELECTING [ sub menu] IN PROCEDURE 4 You can also adjust items in procedure 5 with only the 1 Press the MENU button. selected item displayed.
Page 13
• RGB/COMPO. : sets the input signal of the INPUT A terminal FUNCTION SELECTION (SETTING) • SCAN SIZE : sets the scan size • ASPECT : sets the aspect ratio • COLOR SW : sets the color switch You can select (set) the display’s functions. •...
Page 14
HOW TO PERFORM MAIN MENU ADJUSTMENTS (cont’d.) Connection Between Input Mode Display and DISPLAY OF PRESENT INPUT Frequency (or Color System or DTV Format) Display STATUS Input Input Frequency, Input Mode Frequency, Mode Signal Color System or Display Color You can see the present status of the input mode and frequency DTV Format System or (or color system or DTV format).
Recommended Input Mode List DEGAUSSING THE SCREEN Mode Resolution Horizontal Vertical Preset Frequency Frequency If the monitor is placed too close to a speaker or other device Horizontal Vertical (kHz) (Hz) incorporating a magnet, or if it is moved with the power on, NTSC 15.73 29.97 (i)
HOW TO PERFORM SET-UP MENU ADJUSTMENTS POWER SAVE FUNCTION POWER SAVE FUNCTION SETTING How the Power Save Function Operates ● Horizontal synchronization signal vanishes. This monitor has a power save function. For example, if the power is turned on with no signal input or the signal input is no ≠...
Page 17
CONTROL LOCK OF BUTTONS SETTING DISPLAY OF PRESENT AND KNOBS INPUT STATUS WHEN INPUT IS TURNED ON/OFF You can set the CONTROL LOCK function to disable control buttons and knobs on the front panel, except for the power switch. This function (STATUS DISPLAY) is set in the <SET-UP MENU> screen.
HOW TO PERFORM SET-UP MENU ADJUSTMENTS (cont’d.) Items Contents WHITE BALANCE ADJUSTMENT BLUE DRIVE Adjusts the blue drive level. You can set (adjust) the white balance of the screen. … Decreases the blue drive level. This function (WHITE BALANCE) is set in the <SET-UP MENU> …...
Page 19
SELECTING [ sub menu] IN PROCEDURE 4 RESETTING ALL MENU ITEMS TO You can also adjust items in procedure 5 with only the THEIR FACTORY-SET (INITIAL) selected item displayed. Use this if the full menu screen makes it difficult to observe the monitor image. VALUES Select the [ sub menu] item in procedure 4.
TROUBLESHOOTING Solutions to common problems related to your monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance. Problems Points to be checked...
Page 21
INPUT B indicator blinks : deflection control malfunction When one of these indicators blink, the protection function automatically cuts power. If this happens, turn the power off, unplug the monitor and consult a JVC-authorized dealer or service center for repair.
SPECIFICATIONS Type : DTV monitor Audio Output : 1 W (monaural) Picture Tube : 20” measured diagonally, in-line gun, 90° Built-In deflection, dot-trio type (dot-trio pitch Speaker : 3-1/8” (8 cm) round x 1 0.26 mm) Impedance of 8 Effective Screen Environmental Size : Width...
Page 23
DTV-Format Signals * The following are DTV-format signals that can be input. DTV Formats 480i 480p 720p 1080i Signal Standard ITU-R BT. 601-4 SMPTE 293M SMPTE 296M SMPTE 274M Scanning Lines/Frame 1125 Effective Sample 720 x 485 720 x 483 1280 x 720 1920 x 1080 x Scanning Lines...