JVC DT-V9L5 Instructions Manual page 37

Setting of the function for turning the unit off (standby) automatically when no operations are made for
Off: Does not turn off automatically
On: Turns off automatically
●
When the function is turned On, a warning message will be displayed about 3 minutes before turning off automatically.
When you turn on the unit with the function turned On, a message notifying that the setting is turned on will be displayed for about 30
seconds.
Settings for the sub menu display, color of the tally lamp, and the intensity of the button lamps.
Item To do
sub menu Position Select the contents and displaying position of "sub menu."
Lower1
Upper1
Lower2
Upper2
Tally Setting Set the color and mode of the tally lamp using external control.
Tally Type
Normal
Half
Tally Color
Set the tally color when "Tally Type" is set to "Normal".
Back Tally Enable *
1 Select whether to use back tally lamp.
Dimmer Select the intensity of the button lamps.
Component Phase Deactivates the function of PHASE adjustment (Picture adjustment knob and "Picture Sub
Adjust" in Set-Up Menu) except when an NTSC signal comes in (☞ on page 38).
Remote Active On Set the conditions for the power switch by external control (serial).
Standby
Off
On
LCD Saver
Configure the setting for reducing damage to the LCD panel for long-time use. (☞ on page 41)
Setting 1st Start Set the standby time. (unit: hours)
Work Set the time for performing the function. (unit: hours)
Time
Contrast Set the contrast reduction.
Backlight Reduce the backlight brightness.
OSD Set the contrast reduction of the OSD display.
Contrast
Side Mask Select whether to use the side mask.
reset Restore the default settings for all the items in "LCD Saver".
Execute Execute the LCD Saver function.
Cancel Stop the LCD Saver function. ("Cancel" will be grayed out during the function stop.)
Status Display the LCD Saver status.
Start After Stop the LCD Saver function. (unit: hours and minutes)
Function Key Setting
Specify the function assigned to the F1 button.
Function1 Specify the function assigned to the F1 button.
* See pages 32 to 40 for details of the functions assigned to Function 1.
Function Display Select whether to display the status of the assigned function when you press the F1 button.
Off
Mode-1
Mode-2
●
To display the "Function Key Setting" menu, press the
●
About the operations of F1 button
Each time you press the button, the setting value for the assigned function changes in order.
Ex: When "Color Temperature" is assigned
Each time you press the button, three setting values alternate.
DT-F9L5 only.
* 1
Setting values: Off, On
: Displays the current setting and adjustment bar at the lower part of the screen.
: Displays the current setting and adjustment bar at the upper part of the screen.
: Displays the current setting at the lower part of the screen.
: Displays the current setting at the upper part of the screen.
The adjustment bar is not displayed for some items.
: Light up the entire tally.
: Light up the left and right halves of the tally individually.
: Cannot power on by external control after powered OFF.
: Can power on by external control after powered OFF.
The Side Mask function works no matter whether the LCD Saver is active or stopped.
: No status display. Perform the registration function.
: Display the status. Perform the registration function.
: Display the status. Do not perform the registration function.
Perform the registration function when the status is displayed and the button is
pressed again.
button when the menu is not displayed.
more than 4 hours.
Setting value
Lower1, Upper1, Lower2,
Upper2
Normal, Half
Green, Red
Off, On
Normal, Dark
Enable, Disable
Off, On
00h-24h
01h-06h
Normal, Save
Normal, Save
Normal, Save
Off, On
Off, Ready
**h **min
- - -, Aperture, I/P Mode,
Frame, Center Marker, Level
Meter Display, Gamma, Color
Temperature, CRC Error,
Manual Aspect,Time Code,
1:1, Dynamic, Zebra Mode *
Focus Assist Mode *
1
Off, Mode-1, Mode-2
37 37
1 ,