Appendix A. Partitioning; A1. Programming Partitions; A2. Defining Zones; A3. Enrolling Keyfobs And Keypads - Visonic PowerMaxComplete Installer's Manual

APPENDIX A. Partitioning

Your system is equipped with an integrated partitioning
feature that can divide your alarm system into three distinct
areas identified as Partition 1 through 3. Partitioning can be
used in installations where shared security systems are
more practical, such as a home office or warehouse
building. When partitioned, each zone, each user code and
many of your system's features can be assigned to Partition
1 to 3.
Note: When Partition Mode is disabled, all zones, user
codes, and features of the PowerMaxComplete will operate
as in a regular unit. When partition mode is enabled, all
zones, user codes, and features of the PowerMaxComplete
are automatically assigned to Partition 1.

A1. Programming Partitions

Your system arrives with partitioning disabled.
To Enable Partitioning
A. Enter PowerMaxComplete installer Mode (see par.
4.1.5).
The PowerMaxComplete display will read"1. NEW INSTL
CODE".
B. Click the
PowerMaxComplete display will read:
1 5 . P A R T I T I O N I N G
C. Click . The PowerMaxComplete display will
read:
D i s a b l e
D. Click the
display will read:
E n a b l e
E. Click the
display will change to:
E n a b l e
F. Click the
setting.

A2. Defining Zones

Partitioning is defined by zones that are assigned to each
partition. During programming each zone should be
assigned to one or more partitions.
To Define Zones
A. Enter PowerMaxComplete installer Mode (see par.
4.1.5).
The PowerMaxComplete display will read"1. NEW
INSTL CODE".
B. Click the button twice. The PowerMaxComplete
display will read:
3 D E F I N E Z O N E S
C. Click the
display will read:
Z O N E N o : - -
D. Enter a zone number,
PowerMaxComplete display will read:
Z 0 5 : T Y P E - -
E. Proceed by setting the zone type, name and chime
option (see par. 4.3).
38
button repeatedly until the
button. The PowerMaxComplete
button. The PowerMaxComplete
button again to confirm the new
button. The PowerMaxComplete
for example, 05.
F. After setting the chime option select PARTITION. If zone
number was set to 05 the PowerMaxComplete display
will read:
Z 0 5 : P 1
G. Press ,
corresponding partitions.
or more partitions, this indicates that the zone is
located in a common area and will behave according
to the state of both partitions. (For a detailed
description on common areas, refer to the "Common
Areas" section below.)
H. Press

A3. Enrolling Keyfobs and Keypads

This section provides instructions for enrolling keyfobs and
keypads into the PowerMaxComplete system.
To Enroll a Keyfob
Keyfob transmitter enrolling involves the following steps:
A. Having entered your Installer Code successfully (see
section 4.1.5), Click the
if necessary) until the display will read:
B. Click
C. Click the
will read:
D. Click
E. Suppose that the Keyfob you are about to enroll is to be
designated as Keyfob No. 5. Assuming that memory
location No. 5 is free - no keyfob has yet been enrolled
to it - click the <5> key. The display will change to:
The clear space at the far right tells you that the
memory location is free.
F. Click
a transmission from the chosen keyfob:
G. Initiate a transmission from the chosen keyfob by
pressing any one of its pushbuttons. In response, the
"Happy Tune" (- - - –––) will sound. When partition is
disabled, the display will read:
Proceed to step "K" below.
When partition is enabled, the display will read:
H. Click
The
I. Select the desired partitions that will be associated and
can be controlled by this keyfob via pushbuttons 1, 2
and 3 on the control panel keypad.
J. Click
D-303983 PowerMaxComplete Installer's Guide
P 2 P 3
and to select the desired
If a zone is assigned to two
twice to confirm the settings.
button (repeatedly,
2. ENROLLING
. The display will read:
ENROLLING TYPE
button repeatedly until the display
ENROLL KEYFOB
. The display will read:
KEYFOB No: _
KEYFOB No: 5
. The display will prompt you to initiate
TRANSMIT NOW
KEYFOB No: 5
ACCESS TO PART
. The display will read
F01: P1 P2 P3
. The display will read:
KEYFOB No: 5