Visonic PowerMaxComplete Installer's Manual page 30

The following LAN messages are reported:
Message Description
Unit is ok
Broadband
correctly.
Test aborted
The diagnostic test is aborted, as
follows:
 AC failure – Broadband Module is
set to OFF mode.
 Broadband
completed the power-up procedure.
In this case, the installer should wait
a maximum of 30 seconds before
re-testing.
Comm. loss
The RS-232 serial interface between
the
PowerMaxComplete failed.
Rcvr Ip
Receivers IP 1 and 2 settings are
missing
missing in the PowerMaxComplete.
Cable
The Ethernet cable is not connected
unplugged
to the Broadband Module.
Check lan
This message appears in any of the
config
following cases:
 Incorrect Broadband Module IP has
been entered.
 Incorrect subnet mask has been
WL SENSORS TEST
DIAG. TESTING
(Perform walk test)
BATHROOM
Z19 STRONG
DIAG. TESTING
FRONT DOOR
(alternating for 5 sec.)
Z1 POOR
LIVING ROOM
(alternating for 5 sec.)
Z2 OK
(Each time the OK button is pressed,
the next test result is displayed)
GPRS CONN. TEST
PLEASE WAIT...
UNIT IS OK
When the OK button is pressed, the test result takes
( )
*
between 15 sec. to 4 mins. before it is displayed,
depending on the severity of the failure.
See par. 4.10.1 for a complete list of possible
GSM/GPRS messages and par. 4.10.2 for a
complete list of possible Broadband Module messages.
30
Module is functioning
Module has
Broadband Module and
10. DIAGNOSTICS
WL SIRENS TEST
S1
Example
of test
S1
result
display
S2
Example
of test
result
S2
display
Note
STRONG/GOOD/POOR/
"NOT OK" (with siren No.,
Example
S1 or S2 before) is
of test
displayed according to the
result
wireless siren signal
display
strength).
S1=siren 1. S2 = siren 2.
CPU = Control Panel Unit
LAN CONNECT. TEST
( )
*
Figure 4.10 - Diagnostic Test Flow Chart
Message
Rcvr#1
UnReach.
Rcvr#2
UnReach.
not
Rcvr#1 UnReg.
Rcvr#2 UnReg.
Broadband
Module
timeout err.
the
Invalid result
(see figure 4.1a)
NON-PARTITIONING ONLY
CPU
WAIT
CPU=STRONG
CPU
PLEASE WAIT...
CPU=STRONG
Note
STRONG/GOOD/POOR/
"NOT OK" (with keypad
No., K1 or K2 before) is
displayed according to the
wireless keypad signal
strength).
K1=keypad1 K2=keypad2
CPU = Control Panel Unit
= 2 way comm.
( )
*
PLEASE WAIT...
UNIT IS OK
REBOOT: Resets the Broadband Module
FACTORY DEFIN:
Resets all LAN setting definitions (does not
reset Central Station IP definitions).
D-303983 PowerMaxComplete Installer's Guide
Description
entered.
 Incorrect default gateway has been
entered.
 DHCP server failure.
Receiver 1 or 2 is inaccessible, as
follows:
 Wrong receiver IP has been entered.
 Receiver failure.
 WAN Network failure.
The PowerMaxComplete unit is not
registered to IP receiver 1 or 2.
Broadband Module does not respond
to test result within 70 sec.
Broadband Module responds with a
result code that is not recognized by the
PowerMaxComplete.
WL KEYPADS TEST
K1 CPU
WAIT
K1 CPU=STRONG
K2 CPU
PLEASE WAIT...
K2 CPU=STRONG
= 2 way comm.
LAN RESET OPTION
REBOOT
FACTORY DEFIN.