Enrolling Type; Enroll/Delete Wireless Devices - Visonic POWERMAX+ Installer's Manual

ENROLLING TYPE

OK
normal enroll
by tamper
OK
(First display is READY
or NOT READY)
READY 00:00
NEXT
NORMAL MODE
NEXT
USER SETTINGS
NEXT
INSTALLER MODE
OK
ENTER CODE
[installer code]
1. NEW INSTL CODE
NEXT
OK
2. ENROLLING
NEXT
3. DEFINE ZONES
NEXT
4. DEFINE PANEL
NEXT
5. DEFINE COMM
NEXT
6. DEFINE GSM
NEXT
7. DEFINE PWRLNK
NEXT
8. DEFINE OUTPUTS
NEXT
9. RECORD SPEECH
NEXT
10. DIAGNOSTICS
NEXT
11. USER SETTINGS
NEXT
12. FACTORY DEFLT
NEXT
13. SERIAL NUMBER
NEXT
14. START UL/DL
NEXT
<OK> TO EXIT
Figure 4.2 - Enrolling / Deleting Wireless Devices / Keyfobs / Wireless Commanders / Wireless Sirens
4.2.2 Enrolling Type
Here you determine whether to enroll a wireless device by
normal transmission or by device Tamper function
(opening its cover). Options: normal, or by tamper.

4.2.3 Enroll/Delete Wireless Devices

Wireless devices include various PowerCode detectors
and hand-held transmitters.
DE5467IP
NEXT ENROLL WL DEVICE
OK
SET SENSITIV.
OK
higher sensitivity
lower sensitivity
Select by
NEXT
or
OK
ZONE No: - -
[Zone No.] (e.g. 05)
ZONE No: 05
OK
TRANSMIT NOW
[Initiate transmission)
(**) (***)
ZONE No: 05
NEXT
for next
enrolling action
Enrolling a WL Device
ENROL WL 1WAY KP
OK
1way kp No :
[WL 1-way keypad
No. 1 to 8] (e.g. 5)
1way kp No : 5
OK
TRANSMIT NOW
press
*
key until
red LED
lights)
1way kp No: 5
NEXT
for next
enrolling action
Enrolling a wireless
Commander MCM-140+
ENROL WL SIREN
OK
SIREN No :
[WL siren No.
1 or 2] (e.g. 2)
siren No : 2
OK
TRANSMIT NOW
Momentarily press the
wireless siren self-test
button until a squawk is
heard (1 sec. approx.)
siren No: 2
NEXT
for next
enrolling action
Enrolling a
wireless siren
NEXT
(****)
(**)
ZONE No: 05
OK
<OFF> TO DELETE
ZONE No: 05
Deleting a WL Device
NEXT
(**)
1way kp No : 5
OK
<OFF> TO DELETE
1way kp No: 5
Deleting a wireless
Commander MCM-140+
NEXT
(**)
siren No : 2
Open WL
siren cover
and remove
its battery
OK
<OFF> TO DELETE
siren No: 2
Deleting a
wireless siren
STOP
• Make sure that magnetic contact transmitters are
together with their magnets, to prevent them from
sending out alarm transmissions.
To enroll / delete wireless devices, refer to figure 4.2.
(*)
ENROLL KEYFOB
OK
Keyfob No: -
[Keyfob No.]
(e.g. 5)
Keyfob No: 5
OK
TRANSMIT NOW
(press any
key)
(**)
KEYFOB No: 05
NEXT
for next
enrolling action
Enrolling a Keyfob
ENROL WL 2WAY KP
OK
2way kp No:
[MKP-150 No.
1 or 2] (e.g. 2)
2way kp No : 2
OK
TRANSMIT NOW
Press MKP-150
back tamper
switch once
(see MKP-150
AWAY
inst. instructions)
2way kp No: 2
NEXT
for next
enrolling action
Enrolling a wireless
keypad MKP-150
Keyfob enrolling can be performed by the
(*)
installer or by the user (via USER SETTINGS
menu).
Black box in the display means that a device is
(**)
enrolled (the system has learned its ID). No
black box means the device is not enrolled.
Initiate either normal transmission or the device
(***)
tamper function (see ENROLLING TYPE, par.
4.2.2).
Select "higher" sensitivity for far wireless devices,
(****)
"lower" for near devices.
• Before enrolling, the lens at the front of PIR
and dual-technology sensors should be
masked to prevent inadvertent transmission.
NEXT
(**)
Keyfob No: 5
OK
<OFF> TO DELETE
KEYFOB No: 05
Deleting a Keyfob
NEXT
(**)
2way kp No : 2
OK
<OFF> TO DELETE
2way kp No: 2
Deleting a wireless
keypad MKP-150
9