Table of Contents
Advertisement
16 – Messages and Troubleshooting
Operation messages
ª
Message
A blank recordable MD disc has been
Blank Disc
inserted.
Editing operation has been successfully
Complete
completed.
The unit is being readied for dubbing.
Dubbing
Wait
The table of contents data is being
TOC Reading
read.
The user table of contents data is
UTOC
being written to the disc.
Writing
Editing operation is being performed.
Now Editing
Overwrite recording mode is on.
Over Write
Warning messages
ª
Message
The entire panel is locked. To release
Key Locked
the lock, press and hold the TIME and
DISPLAY buttons simultaneously.
The deck is locked. To release the lock,
CD Locked
select
MD Locked
none
in the SYSTEM submenu of the CD
Eject
menu.
Locked
Error Messages
ª
Message
The disc has malfunctioned. Please
Disc Error!
replace with a new disc.
No recording time remaining on the
Disc Full !
disc, so new recording is not possible.
No more titles can be recorded.
Title Full !
Digital signals are not correctly input.
D-IN UNLOCK!
This message appears if the selected
input source (coaxial or optical) does
not correspond to the connected
terminal or the connected device is
powered off. Select the input source
correctly, or turn on the connected
device.
Editing cannot be completed due to
Not
MD system limitations.
Execute!
There is no audio signal from DIGITAL
Not Audio!
INPUT.
There are no recorded tracks.
No Track !
There is no program
PGM Empty!
No new programs can be created.
PGM Full !
Write-protected MD disc, so recording
W_
or editing is not possible.
Protected!
A playback-only MD disc has been
Pre Master!
inserted.
TOC data is not correct.
TOC Error!
Editing cannot be performed due
Can't Edit!
to MD system limitations or editing
condition limits.
52
TASCAM MD-CD1MKIII
Details/response
Details/response
under
PANEL LOCK?
Details/response
Recording cannot start because the
Can't Rec!
Group playback mode is on.
Menu selection cannot be performed
Can't Sel !
due to selection prohibitions.
You can't undo since no editing has
Can't Undo!
been done.
There was an error during recording.
Rec Error!
Please re-record.
There is a problem in the drive.
Drive Error!
The Sync mode is on, so the recording
Sync Rec
cannot be started manually.
ON!
There is a problem in the data of the
Err Group!
created group.
No groups have been created.
No Group!
The directory where the file is has not
No DIR!
been registered.
The MP3 file cannot be played back.
Decode Err!
All remote control operations are
IR Disable!
disabled.
The unit does not support the format
Format Err!
of the MP3 files on the disc.
Troubleshooting
ª
There is no power to the unit.
Please check that the power cord is properly plugged in.
is displayed.
Disc Error!
The disc may be dirty. Please replace the disc.
Playback is not possible.
This may be due to condensation. In this case, remove
the disc, turn the power on and wait a few hours, then try
again.
No sound is output.
Confirm the connections with the audio system.
•
Check the volume level, and proper amplifier operation.
•
Recording isn't possible.
The MD disc is set to write protect. Slide the tab on the
•
cartridge to the closed position and try again.
Confirm the connections with the audio system.
•
Adjust the recording level.
•
The disc may be for playback only. Please replace it
•
with a recordable MD disc.
Remaining recording time on the MD is insufficient.
•
Please delete unwanted tracks or replace the MD disc.
Confirm amplifier operation.
•
Noise or static can be heard.
Please re-position the unit away from strong sources of
magnetism such as a television.
The MD-CD1MKIII does not retain settings.
While settings are retained each time they are made, in
some cases they will not be retained when the power is
turned off too soon. To prevent this from happening, do
not turn off the power right after making a setting.
Advertisement
Table of Contents
