IF IN DOUBT — CONSULT A COMPETENT ELECTRICIAN. TASCAM CD-X1500 DUAL CD PLAYER IMPORTANT SAFETY PRECAUTIONS For U.S.A TO THE USER This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
… Do not install this apparatus in a confined space such as a book case or similar unit. … The apparatus draws nominal non-operating power from the AC outlet with its POWER switch in the off position. TASCAM CD-X1500 DUAL CD PLAYER English...
Page 4
- IF THIS PRODUCT DEVELOPS TROUBLE, CONTACT YOUR NEAREST QUALIFIED SERVICE PERSONNEL, AND DO NOT USE THE PRODUCT IN ITS DAMAGED STATE. Optical pickup: Type : KSS-213C Manufacturer Laser output Wavelength TASCAM CD-X1500 DUAL CD PLAYER IMPORTANT SAFETY INSTRUCTIONS (2) : SONY Corporation : Less than 0.4 mW on the objective lens : 760 - 800nm...
English 1.1 Environmental conditions The TASCAM CD-X1500 may be used in most areas, but to maintain top performance, and prolong operating life, observe the following environmental conditions: The nominal temperature should be between 5°C and 35°C (41°F and 95°F). Relative humidity should be 30 to 90 degrees non- condensing.
These connectors can output the 44.1KHz digital signals constantly even if pitch control is activated. 7 FADER START jacks (MINI jack) CD-X1500 can be controlled using the external Fader start command through these jacks. Connect the mixer which supports the fader start function with appropriate cable as well as audio signal.
LCD will light Pressing and holding the TIME/ENTER/SHIFT key while pressing the P.MODE key, enters program edit mode. TASCAM CD-X1500 DUAL CD PLAYER 2. Functions and Controls e TIME/ENT / SHIFT key Selects the time display mode, either elapsed, remain, or total remain.
Page 9
2. Functions and Controls r LCD Displays visual feedback for CD-X1500 functions. t TAP / DISPLAY key Set the tempo in BPM by tapping this key. When you press this key, the parameter counter mode momentarily changes to TAP BPM display mode.
TASCAM CD-X1500 DUAL CD PLAYER 2. Functions and Controls … Connect the cable to the CD-X1500 shown on the illustration on the rear panel. If you connect the cable in any other way, you may damage the CD- X1500.
Page 11
Lights when key value is set to other than 0%. ) Parameter display Displays the various parameters. Q TAP indicator Lights when parameter display shows the tap value. W KEY ORIGINAL indicator Lights when key original function is activated. TASCAM CD-X1500 DUAL CD PLAYER English...
If the PLAY key is pressed during CUE playback, the unit will go into normal play mode. 3-3. Flash Start The CD-X1500 has a flash start function that can be used with the CUE 1-3 keys. When the flash start function is activated (when the indicator in the LCD lights), pressing the CUE 1-3 key enables flash start.
CD-X1500 starts loop playback seamlessly. If the loop B point is set when the unit is paused, the CD-X1500 goes to the loop start point then pauses. At this time the LCD lights.
English 3-5. Adjusting the tempo Tempo range The CD-X1500 features +/-8, 16, 32, 100, and 0% of tempo control range. Pressing the TEMPO key changes the tempo control range. The parameter- display shows the selected tempo/key range momentary. If 0% is selected, the parameter display shows .
4. More advanced operation 4-1. Key control The CD-X1500 features up to +/-16% key control. Key control range is determined with tempo range setting. When tempo and key control range is set to 8%, key value can be set in 0.1% steps. When tempo and key control range is set to 16%, key value can be set in 0.2% steps.
3. When track memory number is shown in the LCD, pressing the ENT key recalls the track memory data. The CD-X1500 can recall the track (song) from the track memory data. 1. Select the memory bank by pressing and holding...
When Auto Ready function is turned on, “A.RDY” indicator in the LCD lights. Pressing and holding the SHIFT key then pressing the BEND + key turns the AUTO READY function on and off. TASCAM CD-X1500 DUAL CD PLAYER English...
English 4-10. Programmed Play The CD-X1500 features up to 30 tracks of program play function. Program itself is maintained even if power is turned off, and if CD is not ejected, program list will be backed up. NOTE … If the disc is ejected, program will be erased.
Select the preset menu then press the ENT key, the LCD shows the preset menu and its parameter. Set the parameter with the Jog wheel. Pressing the ENT key confirm the new parameter. Pressing any other key exits the preset operation. TASCAM CD-X1500 DUAL CD PLAYER English...
… Brake on/off … Brake Time … Key Original on/off … Auto Cue on/off … Auto Ready on/off TASCAM CD-X1500 DUAL CD PLAYER 4. More advanced operation Parameter (*: default) Sets the loop mode. A-B loop mode. Single track loop mode.
If the errors continue with a number of discs, turn the unit off, wait for a few seconds, and turn it on again. If the errors still continue or other error occurs, contact your TASCAM distributor for repair. Dimensions (W x H x D mm)
13) Desenchufe este aparato de la corriente durante las tormentas eléctricas o cuando no lo vaya a usar durante un periodo de tiempo largo. TASCAM CD-X1500 REPRODUCTOR DE CD DUAL 14) Consulte cualquier posible reparación únicamente con el servicio técnico oficial. Será necesario reparar este aparato cuando se haya dañado en...
Page 23
Edición del programa ... 36 Inserción del programa... 36 Borrado de programa... 37 4.11 Menú preset ... 37 4.12 Copia de seguridad... 38 5. Especificaciones técnicas... 39 Mensajes de error ... 39 Dimensiones... 40 TASCAM CD-X1500 REPRODUCTOR DE CD DUAL Español...
Español 1.1 Condiciones ambientales El TASCAM CD-X1500 puede ser usado en casi todos los sitios, pero para mantener el rendimiento máximo y alargar su vida operativa, observe las siguientes condiciones ambientales: La temperatura nominal debería estar entre los 5° y 35°...
44.1KHz de forma continua incluso aunque haya activado el control de tono. 7 Conectores FADER START (clavija MINI) Puede controlar el CD-X1500 usando la orden de inicio por fader exterior a través de estas entradas. Conecte la mesa de mezclas que acepte la función de inicio por fader con el cable adecuado, así...
Tecla TIME/ENT / SHIFT Elige el modo de visualización del tiempo entre las opciones elapsed, remain o total remain. TASCAM CD-X1500 REPRODUCTOR DE CD DUAL 2. Funciones y controles ELAPSED: En la parte numérica de la pantalla podrá ver el tiempo transcurrido, discos pero no se iluminará...
Page 27
Jog. (∑ página 33) Con esta tecla también puede activar o desactivar la reproducción consecutiva. (∑ página 35) ; Mando deslizante TEMPO Le permite cambiar el tempo de la reproducción. TASCAM CD-X1500 REPRODUCTOR DE CD DUAL Español...
REMOTE con la que está en el panel trasero de la unidad principal. Precaución … NO use ningún cable con el CD-X1500 que no sea el que viene con el propio 2-5. Mando a distancia (LCD) x Indicador M...
Page 29
Le muestra los distintos parámetros. Q Indicador TAP Se ilumina cuando la pantalla de parámetro muestra el valor de marcación. W Indicador KEY ORIGINAL Se ilumina cuando la función de clave original está activada. TASCAM CD-X1500 REPRODUCTOR DE CD DUAL Español...
Español 3-1. CUE El CD-X1500 puede memorizar el punto de inicio de la reproducción como un punto de escucha o cue. Si este punto cue está memorizado, la unidad se colocará en dicho punto cuando pulse la tecla CUE. Para memorizar el punto CUE Hay dos formas para almacenar este punto de escucha.
El pulsar la tecla B anula el nuevo punto B y hace que salga del modo de edición. NOTA … Solo puede desplazar el punto B a una posición anterior a la que había ajustado antes. TASCAM CD-X1500 REPRODUCTOR DE CD DUAL Español...
Español 3-5. Ajuste del tempo Rango del tempo El CD-X1500 le ofrece un rango de control de tempo de +/-8, 16, 32, 100 y 0%. El pulsar la tecla TEMPO le permite cambiar el rango de control. La pantalla de parámetro le muestra momentánea- mente el rango de tempo/clave elegido.
4. Otras funciones avanzadas 4-1. Control de clave El CD-X1500 le ofrece un control de clave o tono de hasta un +/-16%. Este rango queda determinado por el ajuste del rango del tempo. Cuando ajuste el rango del tempo y del control de clave al 8%, podrá...
3. Cuando en la LCD aparezca el número de memoria de pista, pulse la tecla ENT para cargar esos datos. El CD-X1500 puede cargar la pista real (canción) desde los datos de la memoria de pista. 1. Elija el banco de memoria manteniendo pulsada...
Cuando esta función está activada, en la LCD se ilumina el indicador “A.RDY”. Mantenga pulsada la tecla SHIFT y pulse la tecla BEND + para activar o desactivar la función AUTO READY. TASCAM CD-X1500 REPRODUCTOR DE CD DUAL Español...
Español 4-10. Reproducción programada El CD-X1500 dispone de hasta 30 pistas para la función de reproducción programada. El programa que cree queda memorizado incluso aunque apague la unidad, y siempre y cuando no expulse el CD, podrá recuperar la misma lista de programas.
LCD verá el menú de preset y su parámetro Ajuste el parámetro con la rueda Jog. Pulse la tecla ENT para confirmar el nuevo valor del parámetro. Pulse cualquier otra tecla para salir de este menú. TASCAM CD-X1500 REPRODUCTOR DE CD DUAL Español...
… Frenado on/off … Tiempo de frenado … Clave original on/off … Búsqueda automática on/off … Espera automática on/off TASCAM CD-X1500 REPRODUCTOR DE CD DUAL 4. Otras funciones avanzadas Parámetro (*: valor por defecto) Ajusta el modo de bucle. Modo de bucle A-B.
Si sigue apareciendo el error con varios discos, apague la unidad, espere unos segundos y vuélvala a encender. Si el error persiste o si se produce cualquier otro error, póngase en contacto con su distribuidor TASCAM para que le indiquemos los pasos a seguir para la reparación de su unidad.
Need help?
Do you have a question about the CD-X1500 and is the answer not in the manual?
Questions and answers