NAPCO Gemini GEM-P3200 Installation Instructions Manual page 20

Page 20
NEW COMPAT#
may not be removed for use on a system with a different compatibility number. Note: (1) If assigning compatibility num-
bers, record and store them in a safe place. (2) The GEM-RP2ASe2/GEM-K2AS and GEM-RP3DGTL/GEM-K3DGTL
Keypads will function with or without a Compatibility Number.
While the compatibility number may be changed, the old number must be known in order to program the new number.
Note: If neither the control panel nor the keypad is given a compatibility number, both default to "0000" (thereby main-
taining compatibility).
To program the compatibility number, press the
compatibility number that is programmed into the panel. Note: If the keypad had been previously programmed for a
compatibility number other than "0000", the display would read "OLD COMPAT# XXXX". Enter the existing number before at-
tempting to change it. Press the
EZM ADDRESS
Workbook) similar to its keypad address. If no other EZMs are to be used, designate the keypad as Group "01" at the
EZM ADDRESS 00
" " display. In multiple-EZM systems, enter an assigned group number "01" through "22". (Each EZM
must have a unique assigned group number, starting with "01" and proceeding consecutively). Press the
to continue or press the
C
ZONE RESPONSE
2. Add up the circled numbers.
3. At the keypad, enter the sum as a two-digit number "01" through "15" on the display, then press the
Example. Change Zones 2, 3 and 4 to 50mS response.
1. Circle numbers for Zones 2, 3 and 4: (2), (4) and (8).
2. Add up the circled numbers: 2 + 4 + 8 = 14.
3. Enter "14" at the keypad, then press the
Press the button to continue or press the
A
PROG CONTROL
MESSAGE#
for changes) or press the
01 OUT OF SYSTEM
(display will read "
(top two).
X
GEM-P3200 Installation Instructions
Compatibility Number
The compatibility number is a 4-digit security code that, if programmed into
0000
both the control panel and each GEM-RP1CAe2 keypad, dedicates the
keypad to only that panel. That is, (a) similar keypads not having the cor-
rect compatibility number will not operate in the system and (b) a keypad
A
button to continue or press the
A
EZM Address
The keypad's internal EZM (Expansion Zone Module) may be utilized to
01
provide four additional wired zones. Whether used alone or in conjunction
with optional GEM-EZM series modules or other keypad EZMs, it must be
assigned a unique address (or Group number, see Keypad Programming
button to exit.
Zone Response
The normal loop response of each keypad expansion zone is 750mS, how-
00
ever the response time of any zone can be reduced to 50mS as follows.
1. Of the following, circle the number(s) in parentheses associated with the
zone(s) to be changed: Zone 1=(1); Zone 2=(2); Zone 3=(4); Zone 4=(8)
J
button.
C
Program Control Message
The Access-Control message normally displays "**ENTER NOW**" however
this display may be changed to any of the following messages as displayed
1 in the table at right:
Press the
display will loop back through selections,
button to exit the Keypad Configuration Mode
C
"). Then replace Jumper JP5 across Pins 1–2
button until "NEW COMPAT# 0000" is displayed. Enter the 4-digit
button to exit.
C
button to exit.
button to continue (the
A
WI817F 10/05
A
J
button.
Program Control Message
0 (No Message)
1 **Enter Now**
2 Door Control
3 Gate Control
4 Light Control
5 Control #1
6 Control #2
L
NAPCO Security Systems
button