JUKI DDL-8700 Instruction Manual page 30

!7 Number of rotation of one-shot stitching (Function setting No. 38)
This function can set, by the pedal operation of one time, the sewing speed of one-shot stitching when the sewing
machine continues stitching until completing the number of stitches specified or detecting the material end.
3 8
2 5 0
(Caution) 1. Setting of one-shot stitching is made by the operation panel of the CP-160, or the
function setting No. 76.
2. The max. number of rotation of one-shot stitching is limited by the model of the sewing machine head.
!8 Holding time of lifting presser foot (Function setting No. 47)
Solenoid type presser foot lifter (No. 46 0) can adjust the holding time control of lifting presser foot.
This function automatically lowers the presser foot when the time set with the setting No. 47 has passed
after lifting the presser foot.
When the pneumatic type presser foot lifter (No. 46 1) is selected, the holding time control of lifting presser
foot is limitless regradless of the set value.
4 7
6
!9 Compensation of timing of the solenoid for reverse feed stitching (Function setting No. 51 to 53)
When the normal and reverse feed stitches are not uniform under the automatic reverse feed stitching action, this
function can change the ON / OFF timing of the solenoid for back tack and compensate the timing.
1 Compensation of on-timing of solenoid for reverse feed stitching at the start of sewing (Function setting No. 51)
On-timing of solenoid for reverse feed stitching at the start of sewing can be compensated by the unit of angle.
5 1
Set value Compensation angle
– 36
– 18
0
18
36
2 Compensation of off-timing of solenoid for reverse feed stitching at the start of sewing (Function setting No. 52)
Off-timing of solenoid for reverse feed stitching at the start of sewing can be compensated by the unit of angle.
5 2
Set value Compensation angle
– 36
– 18
0
18
36
3 Compensation of off-timing of solenoid for reverse feed stitching at the end of sewing (Function setting No. 53)
Off-timing of solenoid for reverse feed stitching at the start of sewing can be compensated by the unit of angle.
5 3
Set value Compensation angle
– 36
– 18
0
18
36
Setting range
0
150 to MAX. rpm. <50 / rpm>
Setting range
0
10 to 600 sec <10 / sec>
Adjusting range
1 0
– 36 to 36 <1 / 10˚>
Number of sitches of compensation
– 360˚
– 180˚
0˚
180˚
360˚
Adjusting range
1 6
– 36 to 36 <1 / 10˚>
Number of sitches of compensation
– 360˚
– 180˚
0˚
180˚
360˚
Adjusting range
1 8
– 36 to 36 <1 / 10˚>
Number of sitches of compensation
– 360˚
– 180˚
0˚
180˚
360˚
– 1
– 0.5
–360˚
0
–180˚
0˚
0.5
180˚
360˚
1
– 1
– 0.5
0
0.5
1
– 1
– 0.5
0
0.5
1
28
* W h e n t h e p o i n t
before 1 stitch is
r e g a r d e d a s 0 ˚ ,
compensation is
possible by 360˚ (1
stitch) in front and
in the rear.
360˚
180˚
0˚
– 180˚
– 360˚
360˚
180˚
0˚
– 180˚
– 360˚