JUKI DDL-8700 Instruction Manual page 24

No.
Item
Position where the sewing machin reaches its highest sewing speed from
Pedal stroke for
pedal neutral position (Pedal stroke)
reaching the
44
*
maximum
number of
rotation
Compensation value of the pedal sensor
Compensation of
45
*
neutral point of
the pedal
Auto-lifter selection
Auto-lifter
0 : Solenoid drive system
46
* selecting function
1 : Pneumatic drive system
Holding time of
Limitation time of waiting for lifting solenoid type auto-lifter device
47
lifting auto-lifter
Position where thread trimming starts from pedal neutral position (Standard
Pedal stroke 1
pedal) (Pedal stroke)
48
* for starting
thread trimming
Lowering time of presser foot after the pedal has been depressed.
Lowering time of
(Start of rotation of the sewing machine is delayed during this time.)
49
presser foot
Compensation of
Compensation of starting the solenoid for reverse feed stitching when
solenoid-on
reverse feed stitching at the start of sewing is performed.
timing of reverse
51
feed stitching at
the start of
sewing
Compensation of
Compensation of releasing the solenoid for reverse feed stitching when
solenoid-off
reverse feed stitching at the start of sewing is performed.
timing of reverse
52
feed stitching at
the start of
sewing
Compensation of
Compensation of releasing the solenoid for reverse feed stitching when
solenoid-off
reverse feed stitching at the end of sewing is performed.
timing of reverse
53
feed stitching at
the end of
sewing
Function of lifting presser foot at the time of (after) thread trimming
Foot lift after
0 : Not provided with the function of lifting presser foot after thread
thread trimming
55
1 : Provided with the function of lifting presser foot automatically after
Function of reverse revolution to lift the needle at the time of (after) thread
Reverse
revolution to lift trimming
56
0 : Not provided with the function of reverse revolution to lift the needle
the needle after
thread trimming
1 : Provided with the function of reverse revolution to lift the needle
Bobbin thread
Function of detecting bobbin thread remaining amount at the time of
remaining
(after) thread trimming
amount detection
0 : Not provided with the function of detecting bobbin thread
57
function
1 : Provided with the function of detecting bobbin thread remaining
Function of
Function of holding predetermined upper/lower position of the needle
holding
bar
predetermined
0 : Not provided with the function of holding predetermined upper/
58
upper/lower
position of the
1 : Provided with the function of holding predetermined upper/lower
needle bar
Function of Auto/
This function can specify the sewing speed of reverse feed stitching at
Manual change-
the start of sewing.
over of reverse
0 : The speed will depend on the manual operation by pedal, etc.
59
feed stitching at
1 : The speed will depend on the specified reverse feed stitching
the start of
sewing
Function of stop
Function at the time of completion of reverse feed stitching at the start
immediately after
of sewing
reverse feed
0 : Not provided with the function of temporary stop of the sewing
60
stitching at the
start of sewing
1 : Provided with the function of temporary stop of the sewing
Function of
Function of starting prohibition of the sewing machine by detection of
starting
bobbin thread remaining amount
prohibition of the
0 : This function does not stop the sewing machine when counting
61
sewing machine
by detection of
1 : This function stops the sewing machine when counting is out (-1
bobbin thread
remaining
amount
* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the
time of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
If it is necessary to change the set value, please purchase the Engineer's Manual and follow the instructions.
(Descriptions of setting in this list are the standard values at the time of delivery of DDL-8700.)
However, contents of function setting are subject to change for improvement of function and performance without notice.
Description
trimming
thread trimming
after thread trimming
after thread trimming
remaining amount
amount
lower position of the needle bar
position of the needle bar
speed (No. 8).
machine at the time of completion of reverse feed stitching at the
start of sewing
machine at the time of completion of reverse feed stitching at the
start of sewing.
is out (-1 or less).
or less).
Setting
range
10 to 150
(0.1 mm)
–15 to 15
10 to 600
(second)
–60 to –10
(0.1 mm)
0 to 250
(10 ms)
–36 to 36
(10˚)
–36 to 36
(10˚)
–36 to 36
(10˚)
22
Indication of
function setting
4 4
1 5
4 5
0/1
4 6
4 7
6
4 8 3
4 9
1 4
5 1
1
5 2
1
5 3
1
5 5
0/1
5 6
0/1
0/1
5 7
0/1
5 8
5 9
0/1
0/1
6 0
6 1
0/1
Ref.
page
0
0
0
28
0
5
30
0
28
0
28
6
28
8
1
29
29
0
0 29
29
0
29
1
0
30
1
29