Download
Share
Print this page
  • Contents

Advertisement

IP-900E
IP-900D
IP-900ⅡD
Hardware User's Guide

Advertisement

Chapters

   Also See for Fujitsu IP-900E

Fujitsu IP-900E Hardware User's Manual
Fujitsu IP-900E Hardware User's Manual 116 pages

   Related Manuals for Fujitsu IP-900E

   Summary of Contents for Fujitsu IP-900E

  • Page 1

    IP-900E IP-900D IP-900ⅡD Hardware User’s Guide...

  • Page 2

    (This page is intentionally left blank)

  • Page 3

    The following notice is for USA users only. IP-900E/IP-900D series has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 4

    FUJITSU reserves the right to make changes to any products described herein without further notice and without obligation. No part of this manual shall be reproduced in any way or form without the permission of Fujitsu Limited. © All Rights Reserved. Copyright...

  • Page 5

    SD (Standard Definition) /HD (High Definition) video and audio signals in real time through even the optical IP network like FTTH. (*1) IP-900E has functions that encodes SD/HD video signals from a SD/HD camera or similar device and distributes it across the network in real-time.

  • Page 6: Chapter 1 Preparations

    Chapter 4 and subsequent chapters can be read as required. Chapter 1 Preparations This chapter describes the checks that are required before the start of IP-900E/IP-900D series operation. Chapter 2 Installation and Connection This chapter describes conditions for IP-900E/IP-900D series installation and explains how to connect it to peripheral the devices.

  • Page 7

    If a power receptacle with a low capacity or capacity below the rated value is used, the power receptacle, extension cable or power distribution wiring may overheat and start a fire. Important warning indications are summarized below in “Safety Precautions.” IP-900E/IP-900D series...

  • Page 8: Safety Precautions

    If an excessive heat, smoke, an abnormal odor or an unusual noise is coming from the device, immediately set its power switch to OFF and remove the power cord plug from the power receptacle. Then, contact a Fujitsu Service Center. This indicates a hazardous situation that could lead to fire and electric shock.

  • Page 9

    If a power receptacle with a low capacity or capacity below the rated value is used, the power receptacle, extension cable or power wiring may overheat and start a fire. IP-900E/IP-900D series...

  • Page 10

    • When cleaning the device, please wipe off with the cloth squeezing water (or neutral detergent thinned by water). • When wiping off, please be careful not to put water into the device from switches or the spaces. IP-900E/IP-900D series viii...

  • Page 11

    MADE IN JAPAN I T E I T E 1K91 1K91 E136004 E136004 MODEL IP-900IID 0.35A-0.18A 100V-240V～ PART NO. TA23742-B61X 1φ 50/60Hz 2.3kg 0.035kVA-0.045kVA D08-0454001 09-08 認証番号 00001 12345 FUJITSU LIMITED MADE IN JAPAN I T E 1K91 E136004 IP-900E/IP-900D series...

  • Page 12

    Specifications") can be connected. Otherwise, if incompatible devices are connected, the result may be personal injury and property damage. Disposal To dispose of the device, contact a Fujitsu Service Center, or request a specialist to take care its disposal. Modification and restoration Do not use any device that has been modified or rebuilt with refurbished used parts.

  • Page 13: Table Of Contents

    Connection to ground............. 23 2.2.2 Connection to power source ..........24 Audio and Video Device Connections..........27 2.3.1 IP-900E (Encoder) ..............27 2.3.2 IP-900D/IP-900IID (Decoder)..........28 Connection to Network ............... 29 Connection to RS-232C Device ............30 CF Card Insertion and Removal ............31 Chapter 3 Operation Instructions ............

  • Page 14

    A.3 Preparations for Installation Work ............76 A.3.1 Scope of installation work............76 A.3.2 Unpacking and device check............76 A.3.3 Installation conditions ...............76 A.3.4 Connecting external cables ............76 A.4 Preparations for On-site Turn-up ............77 Glossary and Index .................81 Glossary.......................83 Index ......................86 CE Conformity Information................88 IP-900E/IP-900D series...

  • Page 15: Chapter 1 Preparations

    CHAPTER 1 Chapter 1 Preparations PREPARATIONS This chapter describes the checks that are required before the start of IP-900E /IP-900D series operation. Main Features ············································································ 3 Components··············································································· 4 Basic Application Examples ······················································· 5 Part Names ················································································ 6...

  • Page 16

    (This page is intentionally left blank)

  • Page 17: Main Features

    38VA or less @ 100VAC ○ Temperature -10 to 55°C (No low temperature startup: -10 to -1°C) ○ Humidity 5 to 95%RH (No condensing) *1: IP-900E supports only SD video. By adding optional software, IP-900E will be upgraded to support HD video. IP-900E/IP-900D series...

  • Page 18: Components

    Chapter 1 Preparations Components The IP-900E/IP-900D series product package consists of the following components. Attachments for all series consist of same contents. ･ IP-900E/IP-900D series: 1 pc (cables separate order) ･ Safety manual: 1pc ･ Feet: 4 pcs ･ Holder of power supply cable: 1 pc...

  • Page 19: Basic Application Examples

    Chapter 1 Preparations Basic Application Examples Examples (system configuration) of use of IP-900E/IP-900D series are shown below. IP-900E/IP-900D series...

  • Page 20: Part Names

    Chapter 1 Preparations Part Names This section gives the name and describes the function of individual parts of IP-900E/IP-900D series. The diagrams below show the layout of parts on the outside of the device, and the table below lists the name and describes the function of individual parts.

  • Page 21

    See Section 2.2.1, “Connection to ground,” for an explanation on using (13) (FG ) this terminal. IP-900E start mode selector switch. when the IP-900E is powered on Maintenance mode switch with this switch held down, it starts in initial start mode. (14) See section 3.4, “Mode Switch Setting and Operation,”...

  • Page 22

    See Section 4.2, “Cable and Connector Details,” for cable (L), (R) connection information. Use for an FG connection to the device. FG terminal See Section 2.2.1, “Connection to ground,” for an explanation on using this (12) (FG ) terminal. IP-900E/IP-900D series...

  • Page 23

    Chapter 1 Preparations Names Description IP-900E start mode selector switch. when the IP-900E is powered on with this Maintenance mode switch switch held down, it starts in initial start mode. (13) See section 3.4, “Mode Switch Setting and Operation,” for an explanation on (MNT) using this switch.

  • Page 24

    (This page is intentionally left blank)

  • Page 25: Chapter 2 Installation And Connection

    CONNECTION This chapter describes conditions for IP-900E/IP-900D series installation and explains how to connect it to peripheral devices. Figures described in this chapter are used IP-900E as a sample. Installation Conditions ······························································ 13 Power Supply System Connections ······································ 23 Audio and Video Device Connections ··································· 27 Connection to Network·····························································...

  • Page 26

    Possibility of serious injury The power cord and other cables connected to IP-900E/IP-900D series may become entangled with someone walking close to them, possibly leading to serious injury and property damage. Clamp the cables to the rack or floor.

  • Page 27: Installation Conditions

    Environment conditions Ensure that installation site conditions do not exceed 55°C. Under this condition, IP-900E/IP-900D series can operate in the multiple pile. Otherwise, the operating environment may damage and shorten the product life of IP-900E/IP-900D series noticeably. 2.1.2 Installation environment 1.

  • Page 28

    Chapter 2 Installation and Connection (2) Check all cables disconnected. (3) Connect the first device with the coupling fittings using six same screws (M4). (4) Connect the second device with the coupling fittings using six same screws (M4). IP-900E/IP-900D series...

  • Page 29

    Chapter 2 Installation and Connection (5) Rotate the coupling fittings, and fix with twelve screws (M4). (Bottom view) (Top view) IP-900E/IP-900D series...

  • Page 30

    Chapter 2 Installation and Connection (6) Install the mounting fittings on IP-900E/IP-900D series using six same screws(M4). (7) Install IP-900E/IP-900D series on 19” rack using four screws (M5). IP-900E/IP-900D series...

  • Page 31

    Chapter 2 Installation and Connection One IP-900E/IP-900D series per 1U (1) Check contents of the rack mounting kit. (2) Check all cables disconnected. (3) Install the rack mounting kit A on IP-900E/IP-900D series using three same screws (M4). IP-900E/IP-900D series...

  • Page 32

    Chapter 2 Installation and Connection (4) Install the rack mounting kit B on IP-900E/IP-900D series using three same screws (M4). (5) Install the rack mounting kit C on IP-900E/IP-900D series and rack mounting kit B using four screws (M4). IP-900E/IP-900D series...

  • Page 33

    Chapter 2 Installation and Connection (6) Install IP-900E/IP-900D series on 19” rack using four screws (M5). IP-900E/IP-900D series...

  • Page 34

    Chapter 2 Installation and Connection 2. Desk-top installation Install IP-900E/IP-900D series referring Section 2.1.3, “Air flow into and out from the device” and Section 2.1.4, “Open space required around the device” after sticking the four rubber feet (Rack mounting kit is not required).

  • Page 35: Air Flow Into And Out From The Device

    2.1.3 Air flow into and out from the device IP-900E/IP-900D series is forced air cooled. Be sure not to block the air intake/exhaust vents. Provide an adequate amount of space around the vents. IP-900E/IP-900D series...

  • Page 36: Open Space Required Around The Device

    Open space required around the device Provide the indicated (parts with hatched area) below, cable forming space, operation space and air intake/exhaust. For the information of maintenance space, see Section 5.3.1, “Maintenance space.” 100-240V 100M PWR ALM LINK /ACT IP-900E/IP-900D series...

  • Page 37: Power Supply System Connections

    Connection to ground Use a power cord with the standard two-prong plug with ground wire for FG and external ground connections. When the exogenous noise influences IP-900E/IP-900D series, connect the FG terminal to an external ground. FG terminal (M4) Figure Connection to ground...

  • Page 38: Connection To Power Source

    2.2.2 Connection to power source IP-900E/IP-900D series operation requires a power supply of 100-240 VAC. Insert the power cord with the standard two-prong plug with ground into the inlet connector. The power cord is not supplied with the device. Procure it separately.

  • Page 39

    Note: *l. Be sure that the detachable proper Supply cord has the approval of the appropriate safety agencies of the country where the equipment will be used. *2. Cable length of above Power Supply cord shall be shorter than 4.5 m. IP-900E/IP-900D series...

  • Page 40

    Do not turn on the device until connection of peripheral devices is completed. Otherwise, the device may be damaged. 100-240 VAC Using a power cord with the standard two-prong plug with ground, connect IP-900E/IP-900D series to 100-240 VAC outlet. Provide a power receptacle for the standard two-prong plug with ground. IP-900E/IP-900D series...

  • Page 41: Audio And Video Device Connections

    Audio and Video Device Connections 2.3.1 IP-900E (Encoder) For audio and video encoding, there are two digital video, one analog video, two digital audio and two analog audio terminals to connect audio and video output device. Digital and analog video input Connect to SDI terminal using coaxial cable with BNC connector and input HD-SDI or SD-SDI signal.

  • Page 42: Ip-900d/ip-900iid (decoder)

    For details about connectors and cables, see Section 4.2, “Cable and Connector Details.” NOTE: For electrical specifications, see Appendix 2.3, “Function Specifications.” 100-240V 100M PWR ALM LINK /ACT Video & Audio Input Device Figure Audio and video input device connections IP-900E/IP-900D series...

  • Page 43: Connection To Network

    Chapter 2 Installation and Connection Connection to Network To connect IP-900E/IP-900D series to a LAN device, connect the LAN device to the LAN communication port of IP-900E/IP-900D series using a LAN cable (UTP cable). The LAN communication port specification of IP-900E/IP-900D series is 10BASE-T/100BASE-TX.

  • Page 44: Connection To Rs-232c Device

    The [RS-232C] connector of IP-900E/IP-900D series is the RS-232C communication terminal. The terminal of IP-900E/IP-900D series is the D-sub 9 pins (male) and the specification is DTE. Use a cross connection or straight cable corresponding to the connected device. See Section 4.2, “Cable and Connector Details.”...

  • Page 45: Cf Card Insertion And Removal

    IP-900D/IP-900IID doesn’t support CF card slot. In order to insert the CF card, the front cover of IP-900E must be opened by screwing out the cover. No storage card is supplied with IP-900E. It can be procured separately, depending on the system.

  • Page 46

    (This page is intentionally left blank)

  • Page 47: Chapter 3 Operation Instructions

    This section explains how to power on/off, setup and operate the device. Figures screens described this chapter used IP-900E/IP-900D/IP-900IIDs’ as a sample. Operations and descriptions are common for all equipments. Power ON/OFF ········································································ 35 Device Settings and Operation ················································ 36 Operation Management ··························································· 38 Special Use of MNT Button ······················································ 40...

  • Page 48

    (This page is intentionally left blank)

  • Page 49: Power On/off

    3.1.1 Powering on When the power button on the front panel is set to the [ | ] position, the PWR LED turns on. When IP-900E/IP-900D series completes preparations for operation, the RDY LED turns on. 3.1.2 Powering off When the power button on the rear panel is set to the [O] position, the device is powered off and the PWR LED turns off.

  • Page 50: Device Settings And Operation

    - After rebooted, connected to the user’s network and set up the various parameters. See Section 3.2.2, “Reboot” for more details. Connect user’s network Start settings and operations (Refer the software user’s guide) ■Web browser recommended The recommended web browser is as follow. - Internet Explorer 6.0 SP2 or later IP-900E/IP-900D series...

  • Page 51: Maintenance Page

    3.2.2 Reboot Clicking the button displayed in the left frame of the browser reboots the device. When you click the button, the following dialog box shown below appears for confirmation. Click OK to reboot. IP-900E/IP-900D series...

  • Page 52: Operation Management

    : 255.0.0.0 The page shown below first appears (Initial page at power-on immediately after shipment from the factory). The IP addresses and subnet masks set for the IP-900E/IP-900D series on the LAN, and the gateway setting are displayed. When you operate the IP-900E/IP-900D series with the default settings after shipment from the factory, disconnect the IP-900E/IP-900D series from your network.

  • Page 53: Log

    3.3.2 Log Click Log in the left frame of the browser to display the log information page in the right frame of the browser, where you can check alarm log information on the IP-900E/IP-900D series. Clicking in the right frame deletes all log information.

  • Page 54: Special Use Of Mnt Button

    Chapter 3 Operation Instructions Special Use of MNT Button You can start IP-900E/IP-900D series by turning on the power while holding down the [MNT] Button (for about 10 seconds) until the RDY LED begins blinking in orange. Doing so starts the IP-900E/IP-900D series with the initial IP address and subnet mask with which the IP-900E/ IP-900D series is shipped from the factory (IP address 10.0.0.1, Subnet mask: 255.0.0.0).

  • Page 55: Chapter 4 Cable Specifications

    CHAPTER 4 Chapter 4 Cable Specifications CABLE SPECIFICATIONS This chapter contains a type of how work is implemented, cable connection system diagrams, and cable connector details Installation Preparations··························································· 43 Cable and Connector Details ··················································· 45...

  • Page 56

    (This page is intentionally left blank)

  • Page 57: Installation Preparations

    Chapter 4 Cable specifications Installation Preparations A type of IP-900E/IP-900D series installation work is shown below. (IP-900E) IP-900E/IP-900D series...

  • Page 58

    When constructing a system that uses IP-900E/IP-900D series, consideration must be given so that its boundary between IP-900E/IP-900D series and other devices is similar to that shown in the above figure. Since the type of work may change depending on the system, procure equipment and perform work based on consultations with a system designer.

  • Page 59: Cable And Connector Details

    Front view <IP-900E> <External device> SIGNAL SIGNAL ① ① ② ② Color 30m (Coaxial cable 75Ω 3C-2T) NTSC Mono 200m (Coaxial cable 75Ω 3C-2T) GEN LOCK 200m (Coaxial cable 75Ω 3C-2V) Coaxial cable with BNC connector Product code: TBD IP-900E/IP-900D series...

  • Page 60

    Chapter 4 Cable specifications (3) Analog AUDIO cable IP-900E/IP-900D series...

  • Page 61

    Chapter 4 Cable specifications (4) HDMI cable IP-900E/IP-900D series...

  • Page 62

    ○ ○ ○ ○ ○ <IP-900E> ○ ○ DTR(ER) DTR(ER) <External device> （DTE） ○ ○ (DCE) ○ ○ DSR(DR) DSR(DR) ○ ○ RTS(RS) RTS(RS) ○ ○ CTS(CS) CTS(CS) ○ ○ 15 m (Twisted pair cable with shield 24AWG) IP-900E/IP-900D series...

  • Page 63

    ④ ⑤ ⑤ ⑤ ⑤ ⑥ ⑥ ⑥ ⑥ ⑦ ⑦ ⑦ ⑦ <Straight connection> ⑧ ⑧ ⑧ ⑧ 10/100BASE ：100m UTP cable（Category 5 or more) 5m : TPCBL-B005 10m : TPCBL-B010 50m : TPCBL-B050 100m : TPCBL-B100 IP-900E/IP-900D series...

  • Page 64

    Type HVCTF cross section area NEMA (5-15P) Rated 13A, 1.25 square mm parallel blade 125V 3-Conductors Rated 13 A, 125 V (Single phase;2-current carrying conductors & ground) METI Approved METI Approved METI Approved or <PSE> or <PSE> or <PSE> IP-900E/IP-900D series...

  • Page 65

    *2. Cable length of above Power Supply cord shall be shorter than 4.5 m. CERTIFICATION MARKING Country Agency Certification Mark Country Agency Certification Mark Austria Italy Belgium CEBEC Norway NEMKO Denmark DEMKO Spain Finland Sweden SEMKO France Switzerland Germany IP-900E/IP-900D series...

  • Page 66

    Chapter 4 Cable specifications (This page is intentionally left blank) IP-900E/IP-900D series...

  • Page 67: Chapter 5 Troubleshooting

    CHAPTER 5 Chapter 5 Troubleshooting TROUBLESHOOTING This section explains how to power on/off, setup and operate the device. This chapter describes actions to be taken if the device does not operate normally or if an alarm LED turns on. Figures described in this chapter are used IP-900Es’ as a sample. Help Information·······································································...

  • Page 68

    (This page is intentionally left blank)

  • Page 69: Help Information

    If the action does not solve the problem, contact a service representative. Possibility of electric shock Contact your system administrator before checking the voltage of a power outlet. Otherwise, electric shock may occur. Table 5.1.1 Problem descriptions and recommended actions(IP-900E) No. Class Status Description Recommended action...

  • Page 70

    NTSC (Check decoder setting too.) output is type? distorted. Is the setting of encoder NTSC (Analog input Change encoder setting from NTSC to PAL. when the camera or display is PAL case) (Check decoder setting too.) type? IP-900E/IP-900D series...

  • Page 71

    Connect the LAN and the hub turned on? cable correctly. Device setting Is the IP address specified from the Specify a correct IP address from the Web through a LAN Web browser correct? browser on the control terminal. is disabled. IP-900E/IP-900D series...

  • Page 72

    In the case of a CF card access error, restart the access error has occurred. device. If the problem persists, contact a Fujitsu Service Center. The CF card or the device needs to be replaced. The ALM LED Troubleshoot from the control terminal.

  • Page 73

    Check the device connected. dark. When AGC setting of encoder Encoder is working normal. change ON or OFF, the video The iris adjustment of the camera is possibly contents does not improve normal. necessary. IP-900E/IP-900D series...

  • Page 74

    The DEC LED is stream data. Make sure that ・Are FEC/ARQ settings of this device and the blinking. connected network and the encoder correct? encoder are set/operated correctly. ・Are the network device and LAN port settings (AUTO, Full/Half-duplex, etc) the same? IP-900E/IP-900D series...

  • Page 75: Alarm Led Lamp Is On

    Alarm LED. Blinks or lights in orange when a device alarm occurs. For more details of the alarm log, see Section 3.2.2, “Log” and Section 3.2.7, “Log” of IP-900E/IP-900D series Software User’s Guide.” Lights in green when the HD upgrade option is installed.

  • Page 76: Maintenance

    Please allocate the space more than 1 m in or rear for maintenance. front and rear for maintenance. Front space for maintenance Front space >700mm×1000mm for maintenance >700mm×1000mm Front access case Rear space for maintenance >700mm×1000mm Rear space for maintenance >700mm×1000mm Rear access case IP-900E/IP-900D series...

  • Page 77: Change Of Maintenance Parts (maintenancer Only)

    “Help Information,” change the hardware following the procedure below. The maintenance unit of this product is the whole equipment. When failure, please change whole equipment for the change of the maintenance parts. Please refer Section 2.6, “CF card insertion and removal,” for the respective maintenance. IP-900E/IP-900D series...

  • Page 78

    (This page is intentionally left blank)

  • Page 79: Appendix

    Appendix Appendix The appendix contains view of the device and its main specifications. Notes on installation work and preparations for on-site turn-up are also contained in this section. Figures described in this chapter are used IP-900Es’ as a sample. Appearance·············································································· 67 Basic Specifications ·································································...

  • Page 80

    (This page is intentionally left blank)

  • Page 81: Appearance

    Appendix Appearance The appearance of IP-900E/IP-900D series is shown below. 100-240V 100M PWR ALM LINK /ACT PWR ALM LINK /ACT 100M IP-900E/IP-900D series...

  • Page 82: Bottom View

    Appendix E136004 1K91 LIMITED FUJITSU JAPAN MADE 00001 12345 08-10 D08-0454001 認証番号 0.038kVA-0.048kVA 2.3kg 50/60Hz 1φ TA23742-B50X PART 100V-240V～ 0.38A-0.20A IP-900E MODEL Bottom View IP-900E/IP-900D series...

  • Page 83: Basic Specifications

    Cooling method Forced air cooling (maintenance-free fan used) Power 100-240VAC Weight Max. 2.3 kg IP-900E : 38 VA or less @ 100VAC Power consumption IP-900D : 33 VA or less @ 100VAC IP-900IID : 35 VA or less @ 100VAC A.2.2...

  • Page 84: Function Specifications

    Appendix A.2.3 Function specifications This chapter describes functional specifications of individual parts of the device. (IP-900E only) Name Specifications Remarks Signal format: NRZI Digital SDI Input impedance: 75Ω (Unbalanced) VIDEO input Signal amplitude: 800mVp-p Maximum amplitude level: 800mVp-p ± 10%...

  • Page 85

    Maximum amplitude level: 0.5dB (0dB=100IRE) Permissible cable length: 30m (3C-2T or equivalent) Connector ANALOG VIDEO OUT name Pin number Signal name Remarks SIGNAL (IP-900E only) Name Specifications Remarks Analog voice signal(unbalanced) Analog Input impedance: 54kΩ AUDIO Input maximum level: +2Vrms input Permissible DC input level: ±5Vrms...

  • Page 86

    Pin assignment: Comply with one of two below Pin No. T568A W/G G W/O Bl W/Bl O W/Br Br T568B W/O O W/G Bl W/Bl G W/Br Br [W: white, G: green, O: orange, Bl: blue, Br: brown] IP-900E/IP-900D series...

  • Page 87

    Name Specifications Remarks Parallel 2 pin with ground Input voltage : 100-240VAC±10% Connector : Inlet POWER Button : Locker button Input protection : Built-in fuse Withstand voltage : 1,500 VAC Connector name 100-240V Pin number Signal name Remarks IP-900E/IP-900D series...

  • Page 88

    Appendix (IP-900E only) Name Specifications Remarks Signal format ：TMDS Length of the attested HDMI cable Input impedance ：50 ohms ±10% HDMI input is pretermission. Maximum length ：-------- The unattested cable can't be used. connector ：19PIN Type A Connector name HDMI IN...

  • Page 89

    G LINK established LAN packets detection Cable disconnection [LAN] or software inactive 100M G 100BASE operation 10BASE operation G HD-option installed HD-option not (IP-900E only) installed G Decoding stream Packet loss Not decoding (IP-900D/ stream IP-900IID only) G: Green, O: Orange Name...

  • Page 90: Preparations For Installation Work

    • Place where the device is subject to strong magnetic and radio waves A.3.4 Connecting external cables Refer to Chapter 2, “Installation and Connection,” for the connection methods, Section 4.2, “Cables and Connector Details,” and A.2.3, “Function specifications,” for device connector pin assignments. IP-900E/IP-900D series...

  • Page 91: Preparations For On-site Turn-up

    Input voltage check 入力電圧確認 Power on 電源投入 Unit test 単体試験 System test システム試験 ＥＮ Ｄ Since system configurations of the device are diverse depending on the applications used, this chapter describes the checking process for only a single device. IP-900E/IP-900D series...

  • Page 92

    “Cables and Connector Details,” and A.2.3, “Function specifications,” for device connector pin assignments. Hardware settings need not be set in the device. (5) Input voltage check Make sure that the voltage of power supplied to the device is in a range of 100-240 VAC ± 10%. IP-900E/IP-900D series...

  • Page 93

    2) The LEDs light if the self-check detects an unusual condition. (8) System test 1) Software installation Install appropriate software following IP-900E/IP-900D series Software User’s Guide. 2) Set-up check Various devices settings complying with the system specification are made from the control terminal either directly or via the network.

  • Page 94

    (This page is intentionally left blank)

  • Page 95: Glossary And Index

    Glossary and Index Glossary and Index Glossary ····························································································· 83 Index··································································································· 86 CE Conformity Information ································································· 88...

  • Page 96

    (This page is intentionally left blank)

  • Page 97: Glossary

    (blanking area) of the serial digital IP Address signal. Code used for identifying a node (e.g., PC) operating using TCP/IP. This 32-bit number is FG (Frame Ground) divided into four 8-bit sections, and an example Ground for a cabinet of this is 200.10.101.1. IP-900E/IP-900D series...

  • Page 98

    Mask value used for obtaining a subnet network LED (Light-Emitting Diode) address from an IP address. The subnet The IP-900E/IP-900D series has a power address is obtained by using an AND operation LED lamp and alarm LED lamps. The power between an IP address and subnet mask.

  • Page 99

    100 Mbps. Other 100BASE standards are 10BASE-T4 and 100BASE-FX, and the differ- ence is the type of cable used. 100BASE-TX uses unshielded twisted-pair (UTP) cables. It also uses the RJ-45 connector, which is similar to the modular jacks used for telephones. IP-900E/IP-900D series...

  • Page 100: Index

    LAN cable............49 Cooling method ..........69 LAN interface ............72 Cooling system ............ 3 Ｍ Ｄ Main features ............3 Data input/output ..........3 Maintenance space..........62 Data interface............. 73 Device settings and operation......36 Dimensions ............ 3, 69 Dust ..............69 IP-900E/IP-900D series...

  • Page 101

    Preparation for installation work .....76 Ｗ Preparations ............1 Preparations for On-site Turn-up .....77 Web browser recommended......36 Ｒ Weight ............3, 69 Relay contact input ........7, 8 RS-232C ...........7, 8, 30 RS-232C cable ...........48 RS-232C interface..........73 RS-232C port ..........7, 8 IP-900E/IP-900D series...

  • Page 102: Ce Conformity Information

    Glossary and Index CE Conformity Information Following address can be reached at for regarding the CE conformity information. FUJITSU EUROPE LIMITED Hayes Park Central, Hayes End Road,, Hayes, UB4 8FE, U.K. TEL: 44-20-8573-4444 FAX: 44-20-8573-2643 IP-900E/IP-900D series 88／88...

  • Page 103

    IP-900E IP-900D IP-900IID Hardware User’s Guide December, 2008 1st Edition August, 2009 2nd Edition © FUJITSU LIMITED If this manual is missing a page or pages are not in the proper order, it will be replaced.

This manual also for:

Ip-900d, Ip-900 ii d

Comments to this Manuals

Symbols: 0
Latest comments: