List Of Rc-232C Commands - Pioneer PDP-502MX Manual

RS-232 Adjustment Mode
5.5.4 List of RS-232C commands
How to read this table
• Normal validity : Shows availability in the normal operating mode.
Commands shown as valid are so whether or not preceded by an <AJY> command.
• Direct validity : Shows commands that, if transmitted followed by numerical values, can or cannot directly set
the corresponding items to those values sent out.
• Up/Down validity : Shows commands that, if transmitted followed by UPn/DWn (n standing for any numbers from
0 to 9), can or cannot increase or decrease the corresponding current adjustments by those
numbers.
(NOTE) With regard to the propriety of last memory, please refer to "5.5.1 About the RS-232C adjustment mode".
Command
Name
A ABN ABL NO
ABY ABL YES
AJN ADJUST NO
AJY ADJUST YES
AMN AUDIO MUTE NO
AMY AUDIO MUTE YES
B BBY VIDEO RGB YES
BRT BRIGHTNESS
BHI BLUE HIGH
BLW BLUE LOW
BSL BLUE SIDE MASK LEVEL
BR1 BAUD RATE 1
BR2 BAUD RATE 2
BR3 BAUD RATE 3
BR4 BAUD RATE 4
BR5 BAUD RATE 5
C CFR CLOCK FREQUENCY
CL1 CLAMP MODE 1
CL2 CLAMP MODE 2
CM1 COLOR MODE 1
CM2 COLOR MODE 2
CNT CONTRAST
COL COLOR
CP1 VIDEO COMPONENT-1 YES
CP2 VIDEO COMPONENT-2 YES
CPH CLOCK PHASE
D DIN OSD DISPLAY NO
DIY OSD DISPLAY YES
DOF DISPLAY OFF
DSP INPUT SIGNAL DISPLAY
DW0 DOWN 10
DWn DOWN n
DWF DOWN FULL
F FCA FAN CONTROL AUTO
FCM FAN CONTROL MAX
FMB FULL MASK BLUE
FMG FULL MASK GREEN
FMN FULL MASK NO
FMR FULL MASK RED
FMY FULL MASK YES
FRP FRESH POSITION
FRW FRESH WHITE BALANCE
G GHI GREEN HIGH
GLW GREEN LOW
GPS GET POSITION DATA
GSL GREEN SIDE MASK LEVEL
GST GET STATUS
GS2 GET STATUS 2
GWB GET W/B DATA
134
Normal
Full Name
Validity
¶
¶
¶
‡
‡
(NOTE)
Direct Up/Down
Validity Validity
Sets ABL to OFF.
Sets ABL to ON.
Terminates RS-232C adjustment mode.
Initiates RS-232C adjustment mode.
Turns audio mute OFF.
Turns audio mute ON.
Sets INPUT to VIDEO: RGB.
‡ ‡
Adjusts BRIGHTNESS.
‡ ‡
Adjusts BLUE HIGH-LIGHT.
‡ ‡
Adjusts BLUE LOW-LIGHT.
‡ ‡
Adjusts BLUE SIDE MASK LEVEL.
Sets RS-232C baud rate to 1200 bps.
Sets RS-232C baud rate to 2400 bps.
Sets RS-232C baud rate to 4800 bps.
Sets RS-232C baud rate to 9600 bps.
Sets RS-232C baud rate to 19200bps.
‡ ‡
Adjusts clock frequency.
Sets Clamp Position Setting Mode to 1.
Sets Clamp Position Setting Mode to 2.
Sets White Balance Adjustment Data to Mode 1.
Sets White Balance Adjustment Data to Mode 2 (retake).
‡ ‡
Adjusts CONTRAST.
‡ ‡
Adjusts COLOR.
Sets INPUT to VIDEO: COMPONENT 1.
Sets INPUT to VIDEO: COMPONENT 2.
‡ ‡
Adjusts clock phase.
Disables OSD displays.
Enables OSD displays.
Turns OSD display OFF.
– –
Displays the current input signal information
Decreases adjustment values by 10.
– –
Decreases adjustment values by n.
– –
Decreases adjustment values to minimum.
Makes control of fan's rotation automatic.
Makes control of fan's rotation FIXED (MAX).
Turns full mask blue ON
Turns full mask green ON
Turns full mask OFF
Turns full mask red ON
Turns full mask white ON
Centers the SCREEN adjustment data
Sets picture quality and white balance adjustment
data to median values.
‡ ‡
Adjusts GREEN HIGH-LIGHT.
‡ ‡
Adjusts GREEN LOW-LIGHT.
Sends out position adjustment data in TxD.
‡ ‡
Adjusts GREEN SIDE MASK LEVEL.
Sends out various adjustment data in TxD.
Sends out various settings status data. in TxD.
Sends out picture quality and white balance
adjustment data in TxD.
‡ ¶
or : Yes
¶
= Not put into last memory
Function
: No