Installation Requirements; Tools And Parts - Whirlpool UXT3030AYW0 Installation Instructions And Use & Care Manual

INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed (all models)
• Drill
• 1V4" (3.0 cm) drill bit
• 1/8"(3.0 mm) drill bit for pilot holes
• Pencil
• Wire stripper or utility knife
• Tape measure or ruler
• Caulking gun and weatherproof caulking compound
• Flat-blade screwdriver
• Phillips screwdriver
• Saber or keyhole saw
• Metal snips
• Compass or 8" (20.3 cm) circle template
Parts Supplied (all models)
• T-10 Torx ®tadapter
• T-20 Torx ®tadapter
• 4- 4.5 x 13 mm mounting screws
Parts Needed (all models)
• 3 - UL listed wire connectors
• Vent clamps/duct tape as required
For cabinets with recessed bottoms:
• Two 2" (5.1 cm) wide filler strips. Length and thickness
determined by recess dimensions.
• Four flat head wood screws or machine screws with washers
and nuts (to attach filler strips).
Parts needed
• 31/4"x 10" (8.3 x 25.4 cm) rectangular metal vent system
• Wall or roof cap with damper to match vent system
• 1 - 75W max, 120V incandescent light bulb
Models UXT4030AY/UXT4036AY
(recirculation installation only)
Parts needed
• 1 - 75W max, 120V incandescent light bulb
Models UXT4230AY/UXT4236AY
(vented or non-vented [recirculation] installation)
Parts supplied
Remove parts from package. Check that all parts are included.
• 2 - 3.5 x 9.5 mm screws
• 31/4"x 10" (8.3 x 25.4 cm) rectangular vent connector
Parts needed
• 1 - 75W max, 120V incandescent light bulb
• Wall or roof cap with damper to match vent system
For 7" (17.8 cm) round vented installations:
• 7" (17.8 cm) round metal vent sytem
• 7" (17.8 cm) round damper. For information on ordering, see
the "Accessories" section.
• 7" (17.8 cm) round vent mounting plate. For information on
ordering, see the "Accessories" section.
For 31/4 '' x 10" (8.3 x 25.4 cm) rectangular vented installations:
• 31/4"x 10" (8.3 x 25.4 cm) rectangular metal vent system
For non-vented (recirculation) installations:
• Charcoal filter kit. For information on ordering, see the
"Accessories" section.
Models UXT2030AY/UXT2036AY (vented installation)
Parts supplied
Remove parts from package. Check that all parts are included.
• 2 - 3.5 x 9.5 mm screws
• 7" (17.8 cm) round vent mounting plate
Parts needed
• 7" (17.8 cm) round metal vent system
• Wall or roof cap with damper to match vent system
• 1 - 75W max, 120V incandescent light bulb
Models UXT3030AY/UXT3036AY (vented installation)
Parts supplied
Remove parts from package. Check that all parts are included.
• 2 - 3.5 x 9.5 mm screws
• 31/4"x 10" (8.3 x 25.4 cm) rectangular vent connector
Models UXT5230AY/UXT5236AY
(vented or non-vented [recirculation] installation)
Parts supplied
Remove parts from package. Check that all parts are included.
• 2 - 3.5 x 9.5 mm screws
• 31/4"x 10" (8.3 x 25.4 cm) rectangular damper/vent connector
Parts needed
• Wall or roof cap with damper to match vent system
For 7" (17.8 cm) round vented installations:
• 7" (17.8 cm) round metal vent sytem
• 7" (17.8 cm) round damper. For information on ordering, see
the "Accessories" section.
• 7" (17.8 cm) round vent mounting plate. For information on
ordering, see the "Accessories" section.
For 31/4 '' x 10" (8.3 x 25.4 cm) rectangular vented installations:
• 31/4"x 10" (8.3 x 25.4 cm) rectangular metal vent system
For non-vented (recirculation) installations:
• Charcoal filter kit. For information on ordering, see the
"Accessories" section.
1-®TORX is a registered trademark of Saturn Fasteners, Inc.