Related Manuals for Extron electronics TPS150
Summary of Contents for Extron electronics TPS150
- Page 1 TPS150 Twisted Pair A/V Switching and Transmission System 68-958-01 Rev. B Printed in USA 10 04...
- Page 2 Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock.
- Page 3 Ring output circuits. Balanced Output TPS150 Switching and Transmission System • Quick Start Step 7 Connect a host device, such as a computer or touch panel control, to the transmitter via this 9-pin D connector and a null modem serial port cable for serial RS-232 control.
-
Page 4: Setup And Operation
Quick Start — TPS150 Switching and Transmission System Step 10 Connect a projector or plasma display to the receiver’s video outputs. Output 1 — Connect a VGA cable between the 15-pin HD female connector and the VGA or RGB input on the display. -
Page 5: Table Of Contents
Full system reset ... 3-5 Receiver reset ... 3-5 Optimizing the Video Troubleshooting ... 3-7 General checks ... 3-7 Specific problems ... 3-8 TPS150 Switching and Transmission System • Table of Contents ... 1-1 ... 1-2 ... 1-3 ... 2-2 ... 2-3 ... 2-6 ... - Page 6 ... A-5 Included parts ... A-5 Optional accessories ... A-5 All trademarks mentioned in this manual are the properties of their respective owners. TPS150 Switching and Transmission System • Table of Contents ... 4-1 ... 4-2 ... A-1 68-958-01 Rev. B...
-
Page 7: Chapter 1 • Introduction
TPS150 Switching and Transmission System Chapter One Introduction About this Manual About the Transmission System TP Cable Advantages Features... -
Page 8: About This Manual
• Chapter 4 provides information about programming and operating the switcher under RS-232 control, such as from a PC or host controller. You can control the switcher using Extron’s TPS150 serial command set or the ICS100 control program. • Appendix A lists the transmitter’s and receiver’s specifications and pertinent part numbers. -
Page 9: About The Tpr150 Receiver
/ VG Extron TPT150 AV Switcher Figure 1-1 — Typical TPS150 Switching and Transmission System application About the TPR150 receiver The TPR150 receiver accepts the TP link from the transmitter and outputs the received video and RS-232 commands. The receiver outputs the following signals on the following connectors: •... -
Page 10: Transmission Distance
15-pin HD female VGA connector, enabling a signal to be easily monitored locally without the need for a separate distribution amplifier. Universal projector control — The TPS150 provides universal projector control via serial commands entered by the installing technician. Commands are automatically sent when the input selection or Projector Power buttons are pressed. - Page 11 The CTP150CM is available in a black or white finish and installs in CPM Series modular connector panels that accept a quad-size Mini Architectural Adapter Plate (MAAP). TPS150 Switching and Transmission System • Introduction...
- Page 12 Introduction, cont’d TPS150 Switching and Transmission System • Introduction...
-
Page 13: Chapter 2 • Installation
TPS150 Switching and Transmission System Chapter Two Installation Mounting the Transmitter and Receiver Cabling and Rear Panel Views TP Cable Termination... -
Page 14: Mounting The Transmitter And Receiver
Installation Installation, cont’d Mounting the Transmitter and Receiver The TPS150 comes with rubber feet for the transmitter and receiver, a set of MTR102 rack ears for the transmitter, and a set mounting brackets for the receiver. Rack mounting the transmitter If desired, rack mount the transmitter as follows: Remove the rubber feet from the bottom of the transmitter. -
Page 15: Cabling And Rear Panel Views
S-video, or composite video sources to these BNC and 4-pin mini DIN connectors. For proper system operation, connect only one video format to input 3 and input 4. TPS150 Switching and Transmission System • Installation Projector Mounting Bracket INPUT 2... -
Page 16: Tp And Audio Output Connections
CAUTION See caution Sleeve(s) See caution Unbalanced Output Figure 2-5 — Wiring the audio output connector The audio output always follows the video switch. TPS150 Switching and Transmission System • Installation INPUT 3 VIDEO S-VIDEO S-VIDEO INPUT 3 Composite VIDEO... -
Page 17: Remote Control Connections
Power connection AC power switch — Toggle the AC power switch to the on ( ) position to turn on the transmitter. AC power connector — Plug a standard IEC power cord into this connector to connect the transmitter to a 100 to 240VAC, 50 Hz to 60 Hz power source. -
Page 18: Video Output Connections
Pins 2 3 4 5 6 7 8 2 3 4 5 6 7 8 1&2 3&6 4&5 Figure 2-8 — TP cable termination TPS150 Switching and Transmission System • Installation 568 A 568 B Wire color Wire color RJ-45... -
Page 19: Chapter 3 • Operation
TPS150 Switching and Transmission System Chapter Three Operation Controls and Indicators Operations Optimizing the Video Troubleshooting... -
Page 20: Controls And Indicators
Some projectors use the same command for power on and power off. If the same code is specified for on and off, the Projector Power LED blinks for each button push. TPS150 Switching and Transmission System • Operation PROJECTOR BLANK... -
Page 21: Receiver Controls And Indicators
(CAT 5) cable. See Optimizing the Video on page 3-6 for more details. TPS150 Switching and Transmission System • Operation Sales & Technical Support Hotline to C A B L E E QUA L I Z AT I O N... -
Page 22: Operations
Apply power to the transmitter by connecting the power cord to an AC source and toggling the AC power switch to the on ( ) position. Apply power to the receiver by connecting the power cord to an AC source. -
Page 23: Volume Adjustment
Volume buttons until the transmitter LEDs stop changing and then release the Volume buttons. Receiver reset To reset a TPR150 receiver to its default settings, disconnect TPT150 transmitter power for 10 seconds or more. TPS150 Switching and Transmission System • Operation... -
Page 24: Optimizing The Video
The Skew Adjustment controls are sensitive. Make each adjustment carefully. Repeat steps 4 through 6 to fine tune the adjustments. TPS150 Switching and Transmission System • Operation S K E W A D J R E D B L U E G R N... -
Page 25: Troubleshooting
Ensure that the proper signal format is supplied. Check the cabling and make corrections as necessary. Reset the switcher. See Full system reset on page 3-5. Call the Extron S TPS150 Switching and Transmission System • Operation Sales & Technical Support Hotline if necessary. -
Page 26: Specific Problems
Specific problems The table below shows some common operating problems and their solutions. Problem No image appears. Distorted image appears. TPS150 Switching and Transmission System • Operation Possible cause Solution System not receiving Ensure that the video source, the power... -
Page 27: Chapter 4 • Serial Communications
TPS150 Switching and Transmission System Chapter Four Serial Communications ICS100 Windows Control Program Serial Commands... -
Page 28: Ics100 Windows-Based Control Program
Double-click the setup icon. Click OK in the Run window. Click OK in the InlineControl Setup window. Follow the instructions in the setup program to complete the installation. TPS150 Switching and Transmission System • Serial Communications Recommended: 256 MB Recommended: 1024 x 768... -
Page 29: Establishing Communications With The Program
Click Start > Programs > Extron > ICS100. The control program window appears. The TPS150 does not respond until it has been contacted with the valid address. If you have previously connected to the transmitter and you have not addressed any other device since then, after a moment, the program reports that it has connected to a TPT150 (figure 4-1). - Page 30 Once the transmitter is addressed, it can accept an unlimited number of commands. If a different unit is addressed, the TPS150 ignores subsequent commands until it is addressed again. The factory-installed default address is 97, but this number can be changed.
- Page 31 Click and drag on the slider or click the scroll up ( ) or scroll down ( ) button until an address other than the transmitter’s address is visible. Click on the desired address. Click OK. TPS150 Switching and Transmission System • Serial Communications...
-
Page 32: Using The Software To Configure The Serial Port Settings
If no further operations are to be performed, halt communication with the switcher by selecting a different address. See Establishing communications with the program, step 12. TPS150 Switching and Transmission System • Serial Communications... -
Page 33: Using The Software To Program The Input And Projector Codes
Selecting the Hex radio button causes the transmitter to convert the primary code that you will enter in step 2c to a hex value before saving it. Then, when you press the button, the transmitter sends the hex value. TPS150 Switching and Transmission System • Serial Communications... - Page 34 Line feed Figure 4-11 — Unprintable codes Figure 4-12 — Code entry with unprintable codes Click Program to save the command. TPS150 Switching and Transmission System • Serial Communications Spaces are ok when you are entering ASCII codes. 01234 Code Definition...
-
Page 35: Using The Software To Operate The Transmission System
Using the software to operate the transmission system Use the control program to operate the transmitter as follows: Click Controls > Control Panel. The transmitter control panel window appears (figure 4-14). Figure 4-14 — Transmitter control panel window TPS150 Switching and Transmission System • Serial Communications... -
Page 36: Using The Help System
From the ICS100 startup window, select Help from the Help menu. • From the Button Codes window, press the F1 key. 4-10 TPS150 Switching and Transmission System • Serial Communications button mutes and unmutes the audio output. in the upper right corner of the window to close the window. -
Page 37: Serial Commands
RS-232 port, allowing you to control the display. The transmitter also passes responses on the receiver’s RS-232 port back to its own serial port. TPS150 Switching and Transmission System • Serial Communications Not used Receive data... -
Page 38: Transmitter Responses
The very last command that you send to the transmitter should be the connect, [CC is a different address. This prevents the transmitter from accepting and responding to commands meant for other devices. 4-12 TPS150 Switching and Transmission System • Serial Communications ], command, where ], command, where... - Page 39 = Architectural information: S150•{serial #(9 digits)}•{Rev level (1 character)}•{firmware #(5 or 6 digits)}•{firmware Rev level(2 digits)}• {selected baud rates}1200,2400,4800,9600,19200,38400•{reserved for future use} TPS150 Switching and Transmission System • Serial Communications 04 = input 4 05 = projector power off code...
-
Page 40: Command/Response Table For Programming And Operating The Tpt150
Toggle the blank status [BLANK] Mute the output [MUTE011] Unmute the output [MUTE010] Toggle the mute status [MUTE] Query mute status [MUTE01?] 4-14 TPS150 Switching and Transmission System • Serial Communications (TPT150 to host) {none} [R0• •ADDR •] [R0•95•ADDR95•] [R0• •ADDR@•] [R0• •CH •]... - Page 41 Store hex code to a button [PCH1 Example: [PCH1020F] View a button’s hex code [PCH1 The insert brackets feature is not available for hex codes. TPS150 Switching and Transmission System • Serial Communications (switcher to host) [R0• •VIN 0•] X2 X4 X2 X4 );...
- Page 42 If you change the transmitter’s settings, you may not be able to read the response until you change the controller’s settings. Set transmitter’s serial port parameters [CP1 Reset both serial ports to default [CP1@] View both serial ports’ parameters [CP1?] 4-16 TPS150 Switching and Transmission System • Serial Communications (switcher to host) [R0• •PCL1 @•] [R0• •TOUT05 •] [R0•97•TOUT05060•]...
- Page 43 Toggle front panel lockout [FP] View front panel lockout [FP?] Transmitter reset Reset transmitter [DFLT Architectural information View architectural information [ARC] TPS150 Switching and Transmission System • Serial Communications (switcher to host) [R0• •FP0•] [R0• •FP1•] [R0• •FP•] [R0• •FP?•...
- Page 44 Serial Communications, cont’d 4-18 TPS150 Switching and Transmission System • Serial Communications...
-
Page 45: Specifications
TPS150 Switching and Transmission System A ppendix A Reference Information Specifications Part Numbers... - Page 46 Return loss ... -22dB @ 5 MHz DC offset ... ±0.5 mV with input at 0 offset Sync Input type ... RGBHV, RGBS, RGsB Output type ... RGBHV, RGBS, RGsB (follows input) TPS150 Switching and Transmission System • Reference Information...
- Page 47 Baud rate and protocol ... 38400, 19200, 9600 (default), 4800, 2400, or 1200 baud (configurable); 8 data bits; 1 (default) or 2 stop bits; no parity (default), or even or odd parity TPS150 Switching and Transmission System • Reference Information ®...
- Page 48 Listings ... UL, CUL Compliances ... CE, FCC Class A MTBF ... 30,000 hours Warranty ... 3 years parts and labor All nominal levels are at ±10% Specifications are subject to change without notice. TPS150 Switching and Transmission System • Reference Information...
-
Page 49: Included Parts
Part Numbers Included parts These items are included in each order for a TPS150: Included parts TPS150 twisted pair (TP) switching and transmission system TPT150 switching transmitter TPR150 receiver Rack mounting ears Projector pole mounting brackets 3.81 mm captive screw connector 3.5 mm captive screw connector... - Page 50 Reference Information, cont’d TPS150 Switching and Transmission System • Reference Information...
- Page 51 Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 52 Extron Electronics, USA 1230 South Lewis Street Anaheim, CA 92805 714.491.1500 www.extron.com Fax 714.491.1517 Extron Electronics, Europe Extron Electronics, Asia Beeldschermweg 6C 135 Joo Seng Road, #04-01 3821 AH Amersfoort PM Industrial Building The Netherlands Singapore 368363 +31.33.453.4040 +65.6383.4400 Fax +31.33.453.4050 Fax +65.6383.4664 ©...