Table of Contents
Advertisement
Serial Communications, cont'd
Command/response table for programming and operating the TPT150 (Cont'd)
Command
Program projector power and input command codes (continued)
Reset button code (ASCII or hex)
Assign a projector power timeout
Example:
View the projector power timeout
Projector commands
Send projector power code
Toggle the projector power
Set the power on delay
Set the power off delay
Enable automatic audio mute and
unmute during the projector power
command.
Disable automatic mute/unmute
Serial port configuration
Set both serial ports' parameters
Command description:
Example:
If you change the transmitter's settings, you may not be able to read the response until you change the controller's
settings.
Set transmitter's serial port parameters [CP1
Reset both serial ports to default
View both serial ports' parameters
4-16
TPS150 Switching and Transmission System • Serial Communications
ASCII Command Response
(host to switcher)
(switcher to host)
[PCL1
@]
[R0•
•PCL1
X6
X1
[TOUT05
]
[R0•
•TOUT05
X9
X1
[TOUT05060]
[R0•97•TOUT05060•]
[TOUT05?]
[R0•
•TOUT05?•
X1
[PPWR
]
[R0•
•PPWR
X3
X1
[PPWR]
[R0•
•PPWR•]
X1
[PPWRD1
]
[R0•
•PPWRD1
X10
X1
[PPWRD0
]
[R0•
•PPWRD0
X11
X1
[PPWRM1]
[R0•
•PPWRM1•]
X1
[PPWRM0]
[R0•
•PPWRM0•]
X1
[CP1
02
X12 X13 X14 X15
X12 X13 X14 X15
[R0•
•CP1
X1
1 = transmitter port
2 = receiver port
[CP1
X12 X13 X14 X15
02
X12 X13 X14 X15
Baud
Parity Stop
Flow
Baud
rate
bits
control
rate
[CP130000241110]
[R0•97•CP130000241110•] Set the transmitter's serial port to
0]
[R0•
•CP1
X12 X13 X14 X15
X1
[CP1@]
[R0•
•CP1@•]
X1
[CP1?]
[R0•
•CP1?•
X1
Additional description
@•]
Clear any codes assigned to a
X6
button. The transmitter does not
send any code when the button is
pressed.
•]
Set the transmitter to issue the
X9
power off command
after power on.
The projector is powered off after
60 minutes.
]
The projector power timeout is
X9
set to
minutes.
X9
•]
Send the projector power on or
X3
off (
) command. (0 = power
X3
off, 1 = power on).
If the projector power is on, turn
it off; if it is off, turn it on.
•]
Set the power on (warm up)
X10
delay to
X10
delay, serial commands to the
projector and TPT150 front panel
operation are disabled.
•]
Set the power off (cool down)
X11
delay to
X11
delay, serial commands to the
projector and TPT150 front panel
operation are disabled.
Mute the audio when the
projector power off command is
issued; unmute the audio when
the power on command is issued.
0]
02
X12 X13 X14 X15
X12 X13 X14 X15
0]
Parity Stop
Flow
bits
control
9600 baud, no parity, and 1 stop
bit, Xoff; set the receiver's serial
port to 19200 baud, odd parity, 2
stop bits, and Xon.
0•]
X12 X13 X14 X15
Reset both serial ports to their
default settings: 9600 baud, no
parity, 1 stop bit , and Xoff.
X12 X13 X14 X15 X12 X13 X14 X15
minutes
X9
seconds. During the
seconds. During the
0•]
]
Advertisement
Table of Contents
