Download Print this page

General Maintenance - Craftsman 315.114852 Operator's Manual

1/2 in. 19.2 volt cordless drill-driver variable speed/reversible
Hide thumbs

Advertisement

METAL DR(LLING
For maximum performance, use high speed steel bits for
metal or steel drilling.
== Select normal drilling mode.
== Begin drilling at a very low speed to prevent the bit from
slipping off the starting point.
== Maintain a speed and pressure which allows cutting
without overheating the bit. Applying too much pressure
will:
• Overheat the drill;
• Wear the bearings;
• Bend or burn bits; and
• Produce off-center or irregular-shaped holes.
When drilling large holes in metal, start with a small bit,
then finish with a larger bit. Also, lubricate the bit with oil
to improve drilling action and increase bit life.
A
A
WARNING:
When servicing, use only identical
Craftsman replacement parts. Use of any other part
may create a hazard or cause product damage.
WARNING:
Always wear safety goggles or safety
glasses with side shields when using compressed air
to clean products. If the operation is dusty, also wear
a dust mask.
WARNING:
To avoid serious personal injury, always
remove the battery pack from the product when
cleaning or performing any maintenance.
GENERAL
MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
_
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based
products, penetrating oils,
etc. come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may result
in serious personal injury.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a Sears Service Center.
BATTERIES
This product will accept DieHard<_19.2 V lithium-ion bat-
tery packs and Craftsman 19.2 V nickel-cadmium
battery
packs.
The batteries for this product have been designed to provide
maximum trouble-free life. However, like all batteries, they will
eventually wear out. Do not disassemble battery pack and
attempt to replace the batteries. Handling of these batteries,
especially when wearing rings and jewelry, could result in a
serious burn.
To obtain the longest possible battery life, we suggest the
following:
For lithium=ion
batteries:
== Remove the battery pack from the charger once it is
fully charged and ready for use.
For battery pack storage longer than 30 days:
== Store the battery pack where the temperature is below
80°F and away from moisture.
Store battery packs in a 30%-50% charged condition.
Every six months of storage, charge the pack as normal.
For nickel=cadmium
batteries:
Remove the battery pack from the charger once it is
fully charged and ready for use.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below
80°R
Store battery packs in a "discharged" condition.
BATTERY
PACK REMOVAL
AND PREPARATION
FOR RECYCLING
To preserve natural resources, please
recycle or dispose of batteries properly.
This product uses nickel-cadmium
and
lithium-ion batteries. Local, state or
federal laws may prohibit disposal of
batteries in ordinary trash.
Consult your local waste authority for
information regarding available recycling
and/or disposal options.
A
WARNING: Upon removal, cover the battery pack's
terminals with heavy-duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or re-
move any of its components. Lithium-ion and nickel-
cadmium batteries must be recycled or disposed of
properly. Also, never touch both terminals with metal
objects and/or body parts as short circuit may result.
Keep away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
17

Hide quick links:

Advertisement

loading

  Related Manuals for Craftsman 315.114852

This manual is also suitable for:

315.114853