Single speed / reversible 318in. professional cordless drill-driver (16 pages)
Summary of Contents for Craftsman 315.114500
To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 0( us Visit the Craftsman web page: www.sears.com/craftsman 983000-181 2-03...
16-17 • Parts Ordering / Service ............................... FULL ONE YEAR WARRANTY ON CRAFTSMAN 3/8 in. CORDLESS DRILL-DRIVER If this CRRFTSMIIN 3/8 in. Cordless Drill-Driver fails to give complete satisfaction within one year from the date of pur- chase, RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED STATES, and Sears will replace it, free of charge.
Yourdrill-driver h asmanyfeatures formaking yourdrilling WARNING: Do not attempt to use this product until operations m orepleasant a ndenjoyable. Safety, you read thoroughly and understand completely the performance anddependability havebeengiventop operator's manual. Pay close attention to the safety priority inthedesignofthisdrill-driver making iteasyto rules including Dangers, Warnings and Cautions.
Tool Use and Care • Maintain tools with care. Keep cutting tools sharp • Use clamps or other practical way to secure and and clean. Properly maintained tools, with sharp support the workpiece to a stable platform. Holding cutting edges are less likely to bind and are easier to the work by hand or against your body is unstable and control.
• Never use a battery that has been dropped or received • Do not operate charger if it has received a sharp a sharp blow. A damaged battery is subject to explo- blow, been dropped, or otherwise damaged in any sion.
Important:Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Amperes Current Hertz Frequency (cycles per second) Minutes...
3/8 in. diameter holes per battery pack charge into 2 in. nominal pine lumber. #8 x 1.25 in. wood screws in low speed per battery pack charge into pine lumber. Craftsman EX 114510 - 9.6V test criteria in.lb, torque 3/8 in. diameter holes per battery pack charge into 2 in. nominal pine lumber.
LEVEL MODEL 315.114500 CHARGER 7,2 VOLT TORQUE KEYLESS CHUCK DIRECTION OF ROTATION SELECTOR SWITCH (FORWARD/REVERSE) TRIGGER SCREWDRIVER STORAGE BATTERYPACK CHARGER SHOWNINTOOL PLUG INPUTJACK WRIST Fig. 1 (a) STRAP TORQUE MODEL 315.114510 ADJUSTMENT 9.6 VOLT RING KEYLESS CHUCK LEVEL BATTERY PACKSHOWN IN CHARGING STAND CHARGER DIRECTIONOF...
CHARGING BATTERY PACK FOR WARNING: Always wear safety goggles or safety MODEL 315.114510 glasses with side shields when operating tools. Failure to do so could result in objects being thrown See Figure 1 (b). into your eyes, resulting in possible serious injury. •...
TO INSTALL BAI-rERY PACK SWITCH See Figure 2. • Lock switch trigger on your drill by placing the direction of rotation selector in center position. See Figure 4. To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger.
SWITCH LOCK KEYLESS CHUCK See Figure 4. See Figure 5. The switch trigger can be locked in the OFF position. This Your drill has a keyless chuck. As the name implies, you can feature can be used to prevent the possibility of accidental hand tighten or release drill bits in the chuck jaws.
INSTALLINGBITS REMOVING BITS See Figure 6. See Figure 6. • Lock the switch trigger by placing the direction of • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. rotation selector in center position. See Figure 4. •...
BIT STORAGE DRILLING See Figure 9. See Figure 11. When not in use, bit(s) provided with your drill can be placed in the storage area located on the bottom of your drill. As shown in Figure 9, model 315.114500 has one bit storage slot and model 315.114510 has two bit storage slots.
• Insert hex key in chuck and tighten chuck jaws se- CHUCK REMOVAL curely. Tap sharply with a mallet in a counterclockwise See Figures 12, 13, and 14. direction. This will loosen chuck on the spindle. It can The chuck must be removed in order to use some now be unscrewed by hand.
Do not abuse power tools. Abusive practices can WARNING: When servicing, use only identical damage tool as well as workpiece. Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Only the parts shown on parts list, pages16 and !7, are intended to be repaired or replaced by the customer.
CRAFTSMAN 3/8 in. CORDLESS DRILL-DRIVER MODEL NO, 315.114500 The model numberwill be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your 3/8 in, CORDLESS DRILL-DRIVER or when ordering repair parts.
CRAFTSMAN 3/8 in. CORDLESS DRILL-DRIVER MODEL NO. 315.114510 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your 3/8 in. CORDLESS DRILL-DRIVER or when ordering repair parts.
Get it fixed,lat VoUEl ome er ours! Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold itt For the replacement parts, accessories owner's manuals that you need to do-it-yourself.