3/8 in., 9.6 volts professional cordless drill-driver (18 pages)
Summary of Contents for Craftsman 315.114420
Customer Help Line: 1-800-932-3188 Sears, Roebuc'k and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 visit the Craftsman web page: www,sears,com/craftsrnan 983000 297 11-03...
Exploded View and Repair Parts List ........................... • PaEs Ordering/Service ............................... FULL ONE YEAR WARRANTY ON CRAFTSMAN 3/8 in, CORDLESS DRILL-DRIVER If this I:RRF'r$1_ AN 3/8 in, Cordless Drill-Driver fails to give complete satisfaction within one year from the date of pu_-...
Personal Safety _k WARNING: Read and understand all instructions, Failure to follow a)! instructions listed below, may • Stay alert, watch what you are doing and use resu_ in eiectnc shock, fire and/or serious personal common sense when operating a power tool. Do injury.
Tool Use and Care • Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp • Use clamps or other practical way to secure and cutting edges are less likely to bind and are easier to supped the workpiece to a stable platform.
• Do not operate charger if it has received e sharp ._WARNING : Never use a battery that has been blow, been dropped, or otherwise damaged in any dropped or received a sharp blow. A damaged battery way; take it to a qualified serviceman. Following is subject to explosion.
important: Some ofthefollowing s ymbols m ay beused onyourtool. P lease s tudy them andlearn theirmeaning. Proper irrterpretation of these symbols will allow you to operate the tool better and safer, SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Amperes Current Hertz Frequency (cycles per second) rain Minutes...
Chuck 3/8 in. Keyless M_imum Torque 350 in.lb, Motor DC Motor !6.8 Volt CHARGER Item No. 211041 Gear Train Two Speed (1425301) Switch Variable Speed Rating 120 V, 60 Hz,AC only O 33g/rain (Low) Charging Voltage 24 Volt Load Speed 0 1200/min (High) Charge Rate 1 Hour...
TWO-SPEED LEVEL GEAR TRAIN(HI-LO) TORQUE KEVLESS RING CHUCK LEVEL DIRECTION OF REAR VIEW ROTATION SELECTOR (FORWARD/REV ERSE) TRIGGER STORAGE SCREWD_VER BATTERYPACK SHOWN_ BATTERY PACK SHOWNIN CHARGER _I/2in, WRIST STRAP CHARGER RED LED ON INDICATES GREENLED ON AFTER FASTCHARGING CYCLE,INDICATESFULLY CHARGEDBATTERY PACKAND IN TRICKLE CHARGE MODE Y ELLOWANDGREEN LEDSON INDICATESDEEPLY DISCHARGEDOR DEFECTIVEBATI'ERY PACK.
LI;D FUNCTIONS OF CHARGER WARNING : De no_ allow familiarity with your drill LE-D WILL BE ON TO INDICATE STATUS driver to make you careless. Remember that a careless fraction of a second is sufficient to inflict CHARGER AND BATTERY PACK severe injury.
SW ITCH TO INSTALL BATTERY PACK SeeFigure 2. • Lock switch trigger on your drill by placing the direction Toturnyourdnll O N,depress t heswitch trigger. T oturnit of rotation selector in center position, See Figure 5. OFF, relea'_;e the swilch trigger. •...
SWITCH LOCK KJ=YLESS CHUCK SeeFigure 5. See Figure 6. Theswitch trigger c anbelocked intheOFFposition. This Your drill has a keyless chuck. As the name implies, you can feature conbeused toprevent thepossibility of accidental hand tighten or release dnll bits in the chuck iaws. Grasp and hold the cellar of the chuck with one hand.
INSTALLING BITS RI-'MOVING BITS SeeFigure 7, See Figure 7. • Lock the switch trigger by placing the direction • Lock the switch trigger by placing the direction of rotation sel_cter ir_ c_-;nter position. See Figure 5. rotation selector in center position, See Figure 5. •...
BIT STORAGE Di:_ILLING See Figure 10. $_,_ Figure 12. When not it_ use, bits provided with your drill Can be LEVEL placed in the storage a,_a located on the bottom of your drill as shown in Figure 10. SCREWDRIVER BiTS IIC_: __..__ WAFINING;...
CHUCK REMOVAL • Insert hex key in chuck and tighten chuck jaws sa curely. Tap sharply with a mallet in a counterclockwise See Figures 13, 1_t, and 15 direction. This will loosen chuck on the spindle, Ii san [he chuck must be removed in order to use some now be unscrewed by hand.
WARNING: When servicing, use only identical tool as well as workpieca, Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Only the parts shown on parts list, page 16, are intended to be repaired or replaced by the customer.
CRAFTSMAN 318 in., 16.8 VOLT CORDLESS DRILL-DRIVER - MODEL NO. 315.114420 in ali correspondence regarding your 3/8 in., 16.8 VOLT CORDLESS DRILL-DRIVER or when ordering he model numberwill be found on a plate attached to the motor housing. Always mention the model number repair paEs.
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter made it, no matter sold For the replacement parts, accessories !iiili owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.