Page 1
WARNING: Toreduce the risk of Injury, the user must read and understandthe operator's manual before usingthis product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 Visit the Craftsman web page: www,sears.com/craftsman 983000-329 8-o3...
Page 2
Exploded View and Repelr Parts List........................... • Parts Ordering / Service ............................... FULL ONE YEAR WARRANTY ON CRAFTSMAN 3/8 In. CORDLESS DRILL-DRIVER If this CRRFTSMAN 3/8 In. Cordless DdlI-Ddver falls to give complete satisfaction within one year from the date of pur-...
Page 3
Personal Safety • 1, WARNING: Reed and understand all Instructions. Failureto follow all Instructionslistedbelow, may • Stay alert, watch what you are doing and use msuk in electric shock,fire and/or seriouspersonal common sense when operating a power tool. Do Injury. not use tool while Urad or under the Influence of dregs, alcohol, or medication.
Page 4
servlcad before using. Many acoidents are caused by Tool Use and Care poorly naintair_d teals. • Use clamps or other practical way to secure end Use only accessories that are recommended by the support the workpisee to a stable platform. Holding manufacturer for your model.
Page 5
• ThZ wire size Is large enough for AC ampere _,WARNING: Never usa a battery that has been ral:lngof charger as specified below: dropped or received a sharp blow. A damaged bakery Is subjectto explosion. Properlydispose of a dropped Cord Length (FeeL) 25' 100"...
Page 6
Important: Some of the followingsymbolsmay be used on your tool.Please studythem and leam their meaning. Proper interpretationof these symbolswill allow you to operate the tool better and safer. DESIGNATION/EXPLANATION SYMBOL NAME Volts Voltage Current Amperes Frequency (cyclesper second) Hertz Time Minutes Type or a characteristicnf current AlternatingCurrent...
Page 7
90 In.lb. Chuck In. Key'less MaximumTorque Item No, =11070 Motor DC 9.6 Volt CHARGER (976790-001) Gear Train One Speed 120 V, 60 Hz,AC only Switch Vadable Speed Rating 3-6 Hour No Load Speed O-600/min Charge Rate Clutch 6 Positions BATTERY PACK Item No.
Page 8
BIT STORAGE SCREWDRIVER TORQUE BITS ADJUSTMENTRING KEYLESS CHUCK ROTATION SELECTOR CHARGING STAND UGHT BATrERY CHARGER BATI'ERY PACK SHOWN INTOOL Fig. 1 CHARGER See Figure I.
IMPORTANT INFORMATION FOR RECHARGING WARNING: Do not aJtow familiaritywith your drill- HOT BATTERY PACK driver to make you careless. Remember that a careless fraction of a second Is sufficientto Inflict When usingyour ddl[_dver continuously, the batteries in severe Injury. your battery packwill become hot. You shouldlet a hot bakery pack cooldown for approximately30 minutes CHARGING BATTERY PACK...
TO INSTALL BATTERY PACK SWITCH See Figure 2. • Lockswitch triggeron your drillby placingthe direction of rotationselectorIn center position.See Figure 3, To turnyour drillON, depress the switchtrigger. To turn it OFF, release the switchtrigger. • Place battery pack In your ddlLAlign raised db on battery packwith groove insideddlL See Figure3.
Page 11
KEYLESS CHUCK SWITCH LOCK See Figure 5. See Figure 4, Yourdrillhasa k_=yless c huck. As the name Impites, y ou can The switchtdgger can be locked In the OFF position.This feature can be used to prevent the possibilityof accldental handtightenor releasedrillbitsin the chuck J;tws.Graspand holdthe collarofthe chuck withone hand.
Page 12
REMOVING BITS INSTALLING BITS See Figure 6. See Figum 6. • Lock the switchtdgger by placing the directionof • Loekthe swltchtrigger by ptaolngthe directionof rotation selector In center position.See Figure 5, rotation selectorIn center position.See Figure 4, • Open or close chuck Jawsto a pointwhere the open- •...
Page 13
DRILLING BIT STORAGE See Figure 9, See Figure10. When not In use, bits provided with your drill can be placed In the storage arealocated on the bottomof your ddll as shown in Figure9. SCREWDRIVER BITS BITSTORAGE AREA Fig. lO When drillinghard smoothsurfaces use a center punch to mark desired hole location.
Page 14
CHUCK REMOVAL • Insert hex key In chuck and tighten chuckjaws se- curely.Tap sharplywith a mallet in a counterclockwise See Figures 11,12, end 13. direction,This will loosen chuck on the spindle. It can The chuck must be removed In order to use some now be unscrewed by hand, See Figure 13, accessodes.
Do not abuse power tools. Abusive practicescan damage WARNING: When selvlclng, us=,only Identical tod as well as workplece. Craftsman replacement parts. Use of any other pert may create a hazard or cause productdamage. Only the parts shownon parts list, page 16, are Intended to be repaired or replaced by the customer.All other parts...
CRAFTSMAN 3/8in.,9.6VOLTCORDLESS DRILL-DRIVER - MODEL NO.315.114050 In all correspondenceregarding your318In., 9.6 VOLT CORDLESS DRILL-DRIVER orwhen orderingrepair The modelnumberwillbe found on a plate attached tothe motorhousing.Alwaysrnentlon the modelnumber parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS PARTS UST Part Number Descd_lon Qty.
Page 18
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installationof home appliances and items like garage door openers and water heaters.
Need help?
Do you have a question about the 315.114050 and is the answer not in the manual?
Questions and answers