Drilling - Craftsman 113.213130 Owner's Manual

This Dr_ll Presshas 5 soeeds as listed below:
500 R3M
990 _>M
1500 qPM
2250 RPM
3t00 RPM
See inside of belt guard for specific placement of belts
on pulleys,
SPINDLE SPEE#S iN R.P.Mo
500
1500
2250
[
3100
1. BELT GUARD ASSEMBLY . . . Covers pulleys
and beit dunng operation of dri! 3ross
2. BELT TENSION LOCK HANDLES... T ghtenmg
bandies locks motor bracket support and BELT
TENSION HANDLE [o ma_ntaln correct belt d_s-
lance and tension.
3, BELTTENSlON HANDLE... Turn handle counter
clockwise to apply tension to belt turn handle
c!ockwise to release bett tension
4. HEAD LOCK SET SCREWS . .. Lock the head
to the column, ALWAYS have them locked in p_ace
while operanng [ne drill press
5_ FEED HANDLE... For moving _ne chuck up or
down. One or two of the handles may oe removed
if necessary whenever the workplece _s of such
unusual shape that it interferes with the handles
6. COLUMN COLLAR .. Holds the rack to the col-
umn Rack remains movable ir collar to permit
table suoport movements
7. TABLE SUPPORT.,. Rides on column _o support
arm aria table.
8. TABLE CRANK _ . . Turn clockwise to elevate
table. Support lock must be released before operat-
ing crank
9_ RACK... Combines with gear mechamsm to _ro-
vide easy elevation of table by hand operated talale
crank
10. BASE,.. Supports Drill Press For additional sta-
bility, holes are orovided Jn base to bolt Dril Press
to floor. _See "Additional Safet_ instructions for Drill
Presses."/
t 1. COLUMN SUPPORT... Supports column, guides
rack. and provides mounting holes for column to
base.
12, COLUMN.,. Connects head, table and base on
a one-piece tube
merit, for easy alignment and move-
t3_ TABLE,,. Provides working Surface to support
workoiece.
14 DEPTH SCALE ... Shows depth of hole being
drilled
!5 DEPTH SCALE INDICATOR... Indicates drilling
oepth se4ected on depth scale
16. DEPTH SCALE LOCK... Locks [no depth scale
to selected oeptn.
17 SPRING CAP ... Provides means to aG ust quill
spring tension.
18 CHUCK... Holds dnll b_t or other recommended
accessory [o oerform desired operations
19, ARM... Extends beyond table support for mount-
_ng ano aligning the table
20 TABLE BEVEL LOCK... LOCKS the table in any
posJuon from 0 -45
21 TABLE LOCK... Table can be rotated n various
positions and locked
22 BEVEL SCALE... Shows degree table is tilted
for beve operations. Scale is mounted on side of
arm.
23 SUPPORT LOCK.. Tightening locks taole sup-
port to column. Always have t locked _n 31ace while
operating the Drill Press.
24 CHUCK KEY . . . It is a self-electing chuck key
which wl "'oop" OUt of the chuck when you let go
of it This action is designed to help prevent throw-
ing of the chuck Key from the ChUCk when power
_s turneo "ON'. Do not use any other key as a
substitute, order a new one if damaged of lost
25 BELT TENSION. ,. Refer to section "Assembly-ln-
stallTng ano Tensioning Belt'
26 DRILLING SPEED... Can be changed by placing
the belt _n any of tr_e STEPS grooves _n the pul-
leys See Spindle Speed _nslde belt guard
To deterrntne rtqe approximate drltlllqg speed for
specific materials refer to the table inside tne belt
guard
18