Download Print this page

Advertisement

f
Save ThisManual "_
I
For FutureReference
MODEL NO.
113.213090
DRILL PRESS WITH
MAXIMUM
DEVELOPED
1/2 HP MOTOR
Serial
Number
Model
and
serial number
may be found
at the rear of
the head.
You should
record
both
model
and serial number
in
a safe place
for future
use.
CAUTION:
READ ALL
iNSTRUCTIONS
CAREFULLY
BENCH
MOTORIZED
10-INCH
MODEL DRILL PRESS
• assembly
• operating
e repair parts
",...
.j
../
Sold by SEARS, ROEBUCK AND CO., Chicago,
IL 60684
U.S.A.
Part No. SP5t85
Printed
in Taiwan

Advertisement

   Summary of Contents for CRAFTSMAN 113.213090

  • Page 1

    Save ThisManual "_ For Future Reference MODEL NO. 113.213090 DRILL PRESS WITH MAXIMUM DEVELOPED 1/2 HP MOTOR Serial Number Model serial number may be found at the rear of the head. You should record both model and serial number MOTORIZED a safe place for future use.

  • Page 2

    GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS 1, KNOW YOUR POWER TOOL Z87.1) at al! times. Everyday eyeglasses are not Read and understand the owner's manual and safety glasses. They only have impact resistant labels affixed to the tool Learn its application and lenses Also.

  • Page 3

    additional safety instructions for drilm presses WARNING: FOR YOUR OWN SAFETY, DO NOT d: To prevent the workpiece from being .E _ ATTEMPT OPERATE YOUR DRILL PRESS torn from your hands, spinning of the _" UNTIL iT iS COMPLETELY ASSEMBLED AND IN- toot.

  • Page 4

    13 Think Safety, Safety is a combination of operator b. Drumsanders must NI _ER be operated on common sense and alertness at all times when the the drill press at a sp_ d greater than 1800 drill press is being used. RPM.

  • Page 5

    glossary of terms 1. Workpiece 4. Revolution Per Minute (R.P.M.) The number of turns completed by a spinning object The item on which the cutting operations is being in one minufe, performed. 2. Drill 5. Spindle Speed The cutting toot used in the dril_ press to make holes The RPM of the spindle.

  • Page 6

    i_i !i_ i_i_i _ ° t i¸ motor spec Tca ons and electrica requ reme MOTOR SPECiFICATiONS This power tool is equipped with a 3-conductor and grouna_ng type plug, approved by Underwriters' TNs dril! press is designed to use a 1725 RPM motor Laooratories and the Canadian Standards Association: only.

  • Page 7

    unpacking and checking contents TABLE OF LOOSE pARTS WARNING: AVOID iNJURY FROM UNEX- PECTED STARTING OR ELECTRICAL SHOCK, Item Description Qty. NOT PLUG THE POWER CORD iNTO A SOURCE " " r, ,_, Asrlr_..Tae e Su_..pL t ..... "_ OF POWER.

  • Page 8

    List of Loose Parts in Box 507884 item Description Qty. Chuck Key ....... Chuck ......List of Loose Parts in Bag 507885 item Description Qty. C Feed Handle ......D Wrench Hex "L" 3mm ....E Wrench Hex "L" 4mm ....*F Knob ......

  • Page 9

    location and function of controls 1, BELT TENSION LOCK HANDLES... Tightening 7. DRILL "ON-OFF" SWITCH . . . Turns drift press handles locks motor bracket support and BELT on and off . . , also used to lock drill press in off _ TENSION HANDLE to maintain correct belt dis- position, ,_ o...

  • Page 10

    FRAMING SQUARE MUST BE TRUE, -Check its accuracy as il;ustrated below, DRAW LIGHT STRAIGHT EDGE OF LINE ON BOARD BOARD 3/4" THICK-- ..TOOLS NEEDED ....THIS EDGE MUST BE ALONG THE EDGE ,_ PERFECTLY STRAIGHT SCREWDRIVER SQUARE _J" 8-INCH ADJUSTABLE WRENCH SHOULD BE NO GAP...

  • Page 11

    SPECIAL NOTE: Make sure the elevation worm gear shaft is extending through the opening in the table sup- port as far as possible -- See Illustration. 2. With long smooth end of rack pointing upward, slide rack down through large round opening in table support.

  • Page 12

    COLUMN COLLAR 4. Replace column collar and position it bevel side down over rack. Tighten set screw in collar with 3ram HEX "E' wrench. To let the rack slide when the table is swung to the left or right around column, the collar must s_t loosely...

  • Page 13

    INSTALLING THE HEAD CAUTIONi head assembly weighs about pounds. Carefully li_ head. 1. Remove protective covering from head. 2. Carefully lift head above column tube and slide it down on the column as far as it will go. Align head with table and base.

  • Page 14

    FEED HANDLE !NSTALL{NG FEED HANDLES Lecate th_-ee _3i feed handl_-s amor; 9 io0se pa,*ls. S(_w _ie feed ha:nd_es tight!y i_to 1he threaded _ht hub INSTALUNG THE CHUCK _ocale the chuck among loose parts CIear: out the TAPERED HOLE in the chuck: clean the spindle nose with a clean cloth.

  • Page 15

    BELT GUARD KNOB NO. SCREW 5rr_m DiA x !2ram LONG SCREW BELT GUARD KNOB INSTALUNG BELT GUARD KNOB To attach belt guard k:ob !ocate knob ar'd 5ram × 12ram ong par] hd screw _ loose parts _nstalJ sc_ew n hoe ocated _n guarc and ab taCh knob t_rnmg ;_;1_ l/ghl...

  • Page 16

    4 _._ove t he_d.1or r earwaro toaop_y t e_ls_on tothe 5. Tighten Beet Tension LOCk Handles NOTE: B e_,t SHOULD deflect a pprox_matew '_ by thuntb pressure at mid-point of be_t between pulleys. 6 C_ose De_1[ g uard. _ be_t s_[_£ ,*rhine drfihng, readjust belt tension.

  • Page 17

    knOW your driSl getting press BELT GUARD FEED HANDLE BELT TENSION LOCK HANDLE DEPTH SCALE LOCK COLUMN COLLAR DEPTH SCALE DEPTH rABLE SUPPORT iNDiCATOR FEED SPRING ADJ USTME NT TABLE FEED TABLE CRANK SPRING RACK COLUMN COLUMN SUPPORT BASE ON-OFF SWITCH HEAD LOCK...

  • Page 18

    SPINDLE[ SPEEDS R.P.M. This Drill Press has 4 speeds as listed below: 480 RPM 930RPM 1750 RPM 3000 RPM 1750 3OOO See inside of belt guard for soecific placement of belts on pulleys. SUPPORT LOCK . . . T ghtentng locks tabe sup- BELT GUARD...

  • Page 19

    DRILL "ON-OFF" SWITCH . .. Has Iocmng feature €.J THIS FEATURE tS XITENDED TO HELP PREVENT UNAUTHORIZED AND POSSIBLE HAZARDOUS USE BY CHILDREN AND OTHERS L, U . =:::: & Insert KEY into swftch NOTE: Key _s made of yellow plastic.

  • Page 20

    REMOVING THE CHUCK Open jaws of chuck as wide as they w_lt go by turning chuck sleeve, 2. Carefully tap chuck w_th mallet n one hand while holding other hand under chuck to catch _t when _t falls. It may be necessary to lap tlqe crluck several different spots around the top of the chuck.

  • Page 21

    ANOTHER -- DEPTH SC/_LE 1. With the switch OFF, loosen the depth scale lock. DEPTH SCALE 2. Turn the depth scale clOCkWiSe until the depth scale LOCK indicator points to the desired drilling depth on the depth scale. DEPTH 3. Tighten the depth scale lock.

  • Page 22

    has c dr=l| press operation • Follow the following instructions for operating your drill Never do any work "FREE HAND" (hand- holding workpiece rather than supporting on the table), except when polishing_ Securely lock Head and Support to Column, and table to support before operating drill...

  • Page 23

    POSITIONING TABLE AND WORKPiECE Lock the table to the column in a position so that the tip of the drill is just a little above the top of the work- piece. Always place a piece of BACK-UP MATERIAL (wood, plywood .

  • Page 24

    WARNING: TO AVOID INJURY FROM SPINNING Before urnmg the switch ON, bring the drill down to WORK OR'TOOL BREAKAGE, ALWAYS CLAMP the workpiece lining it up with the hole location. WORKPIECE AND BACKUP MATERIAL SECURELY FEEDING TO TABLE BEFORE OPERATING DRILL PRESS WITH THE TABL E TILTED.

  • Page 25

    maintenance )WARNING YOUR SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAiNTAINiNG OR LUB- RICATING YOUR DRILL PRESS. Frequently blow out any dust that may accumulate in- side the motor. A coat of furniture-type paste wax applied to the tab}e and column wilt help to keep the surfaces clean.

  • Page 26

    trouble shooting WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING. ® CONSULT YOUR LOCAL SEARS SERVICE CENTER IF FOR ANY REASON MOTOR WILL NOT RUN REMEDY PROBABLE CAUSE TROUBLE 1.

  • Page 27

    PARTS CRAFTSMAN 10" DR_LL PRESS MODEL NO. 113,213090 Always order by Part Number--Not by Key Number FIGURE 1 PARTS LIST ..-TT--q Part Key i Part Description Description Knob 817358-2 817325 Screw-Wash 816755G Screw-Pan Hd M5 x 0 8-12 M6×...

  • Page 28

    PARTS LIST FOR CRAFTSMAN 10" DRILL PRESS MODEL NO. 113.213090 ;:3. FIGU_2...

  • Page 29

    PARTS LIST FOR CRAFTSMAN 10" DRILL PRESS MODEL 113.213090 Always order by Part Number--Not by Key Number FIGURE 2 PARTS LIST "O Part ¢e Description Description Head w/Pointer & Trim 816113 Switch-Locking eMotor 815863 1817610 Key-Switch I 3 t ST0840812...

  • Page 30

    PARTS LIST FOR CRAFTSMAN 10" DRILL PRESS MODEL NO, 113.213090 Always order by Part Number--Not by Key Number FIGURE 3 PARTS LIST Part Description Description ..817599 Tube-Column 817447 Screw-Hex Hd 1/2-12 x 7/8 Rack 817601 817608 Table 817600 817772...

  • Page 31

    NOTES...

  • Page 32

    MOTORIZED SERVICE Now that you have purchased your 10-inch Drill Press, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you call...

Comments to this Manuals

Symbols: 0
Latest comments: