Table of Contents
Advertisement
MODEL
NO.
113.213702
DRILL
PRESS ONLY
113,21378(}
DRILL
PRESS WITH
1/2 HP MOTOR
Serial
Number
...........................
Model and serial
number may be found
at the rear of the head.
You should record both
model and serial number
in a safe place for
future use.
CAUTION-
o
Read
GENERAL
and
ADDITIONAL
SAFETY
INSTRUCTIONS
carefully
CRRFTSMRNo
i
75-I/2
INCH
DRILL
PRESS
• assembly
, operating
• repair parts
Sold by SEARS,
ROEBUCK
AND
CO., Chicago,
iL. 60684
U.S.A.
Part No. 71190
..P_i,_,_,,4. iq. U.S.A
Advertisement
Table of Contents
Related Manuals for Craftsman 113.213780
Summary of Contents for Craftsman 113.213780
- Page 1 MODEL 113.213702 DRILL PRESS ONLY 113,21378(} DRILL PRESS WITH 1/2 HP MOTOR Serial Number ......Model and serial number may be found at the rear of the head. You should record both CRRFTSMRNo model and serial number in a safe place for future use.
- Page 2 FULL ONE YEAR WARRANTY ON CRAFTSMAN DRILL PRESS If within one year from the date of purchase, this Craftsman Drill Press fails due to a defect in material workmanshi p, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE...
- Page 3 additional safety instructions for drill presses WARNING: YOUR SAFETY, Never perform operation moving ATTEMPT TO OPERATE YOUR DRILL PRESS UNTIL Head or Table with respect to one another. COMPLETELY ASSEMBLED nNSTALLED pull motor switch "ON" or start ACCORDING TO THE RNSTRUCTIONS .
- Page 4 additional safety instructions for driJJ presses WEAR YOUR The operation power tool result in foreign objects being thrown into the eyes, which can result severe eye damage. Always wear safety goggles complying with ANSI Z87.1 (shown on Package) before commencing power tool operation.
- Page 5 RECOMMENDED MOTORS DUAL VOLTAGE. This plug requires treating 3-conductor grounded type outlet as shown, THESE CRAFTSMAN MOTORS HAVE BEEN If the outlet planning to use for this power tool FOUND TO BE ACCEPTABLE USE ON THIS TOOL. the:; two prong...
- Page 6 assembly WARNING: YOUR SAFETY, NEVER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETED, 1. Unwind the power cord. Make sure the quill lock handle is tight. Stand on the left side of the drill press and LOOSEN the HEAD LOCK HANDLE.
- Page 7 Apply a light film of oil such as Sears household oil to the spindle nose. Place chuck on the spindle nose screw CHUCK locking collar up as far as it will go. LOCKING COLLAR CHUCK CHUCK Insert a piece of 1/4" dia.
- Page 8 assembly INSTALLING DEPTH STOP Screw the THUMB SCREW partways into the DEPTH DEPTH POINTER. FEED POINTER STOP Place the DEPTH POINTER SHOE inside the pointer. Loosen QUILL LOCK HANDLE lower the qui|l about two inches. Slide the pointer and shoe onto the FEED STOP ROD and tighten...
- Page 9 9. Gently push down on the FEED HANDLES until head raises upwards as far as it will go. 10, TIGHTEN HEAD LOCK HANDLE QUILL LOCK HANDLE. HEAD LOCK HANDLE 11. HOLD onto Feed Handle UNLOCK the quill lock handle. 1 2. Let the quill return to the UP position in the head.
- Page 10 assembly 3/16 × 3/16 FLAT SPOT NOTE: When using motors which have V2" dia. shafts, place the adapter sleeve (furnished with the motor) the shaft so that the slot in the sleeve is over the flat spot, Insert shaft (furnished with motor) into...
- Page 11 Remove belt guard by "pushing in" on the two "links". Place motor on drill press screw the pivot screws into the holes. NOTE: DO NOT SCREW THEM IN TOO TIGHT EXCESSIVE TIGHTNESS COULD BEND MOTOR MOUNT. Find 5/16 in-18 hex. nuts among the loose parts...
- Page 12 assembly iNSTALLING AND TENSIONING BELT Place a straightedge such as a piece of wood, metal framing square across the pulleys. Move motor UPWARDS until the pulleys are IN LINE tighten the motor mounting nuts with a ½ in. wrench. Place the belt on the pulleys. BELT TENSIONIN_ MOTOR 4.
- Page 13 getting to know your dri B press SWITCH -_--- SPLINES (GROOVES) '-'---- SPINDLE QU ILL DRILL RACK "ON-OFF" (TEETH) SWITCH QUILL SPINDLE ASSEMBLY INSIDE OF DRILL PRESS DEPTH SCALE SUPPORT CO[iAR QUILL SCRE'¢,: HANDLE DEPTH POINTER HANDLE CHUCK LOCK COLLAR HANDLE CHUCK CHUCK...
- Page 14 getting to know your drill press HEAD LOCK HANDLE locks the head to the column. ALWAYS have collar LOCKED into position ALWAYS have it locked in place while operating the drill approximate{y 34 in. from floor average drilling press. operations. HEAD SUPPORT COLLAR prevents the head from CHUCK...
- Page 15 LOCKING COLLAR CHUCK REMOVING THE CHUCK. Iris7 Insert apiece of 1/4 in. alia. steel rod in one of the holes in the chuck body. Insert the CHUCK into one of the holes in the collar turn direction arrow until LOOSE. Continue to turn it until...
- Page 16 basic drill press operation properly that cutting tool is not causing recommend following instructions operating excessive vibration. your drill press so that best results and to minimize the likelihood of personal injury, Never perform operation freehand (hand-holding workpiece rather than supporting it on table) except...
- Page 17 HOLE LOCATOON allow the drill to cut. Make a DENT in the workpiece where you want the hole . . . using a CENTER PUNCH or a SHARP NAIL. Feeding SLOWLY might cause the drill to burn Before turning the switch bring the drill down...
- Page 18 maintenance WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAINTAINING OR LUBRRCATJNG YOUR DRI LL PRESS. Frequently blow out any dust that may accumulate inside the motor. A coat of automobile-type applied to the table column will help to keep the surfaces clean.
- Page 19 troubRe shooting WARNING: FOR YOUR OWN SAFETY, TURN SW_TCH "OFF" ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING, PROBABLE CAUSE TROUBLE REMEDY Incorrect belt tension Noisy Operation 1. Adjust tension. See section "Getting To Know Your Drill Press"...BELT TENSIONING ROD.
- Page 20 PARTS LIST FOR CRAFTSMAN DRILL PRESs MODEL 113.213702 & 113.213780 (5E_ FIGURE 9,.._ --'_ lO (SEE FIGURE "l) MOTOR SWITCH Figure WIRING DIAGRAM...
- Page 21 PARTS LIST FOR CRAFTSMAN DRILL PRESS MODEL NO. 113.213702 & 113.213780 Always order by Part Number -- not by Key Number FIGURE 1 PARTS LIST Part Part Description Description 71098 71097 Scale, Depth Pulley Assembly (See Figure STD 541110 60193...
- Page 22 PARTS LIST FOR CRAFTSMAN DRILL PRESS MODEL NO. 113.213702 & 113.213780 ==iP "--4 __2--- FIGURE 2 PARTS LIST Part Description 71173 Pan'el, Front Guard 144987 *Screw, Type B, Flat Hd., No. 10 x 1/2 71069 Guard STD 610807 *Screw, Type B, Pan Hd., No.
- Page 23 PARTS LIST FOR CRAFTSMAN DRILL PRESS MODEL NO. 113.213702 & 113.213780 FIGURE 3 - 71075 SPINDLE ASSEMBLY, STOP Key I Part Description 71075 Spindle Assembly, Stop 37158 Ring, Retaining, 3509 Bearing, Ball 71147 Tube, Quill 27813 Gasket, Quill 60176 Washer, Quill...
- Page 24 ] 5q/2 NCH DRILL PRESS SERVmCE that have purchased your 15-1/2 inch drill press should a need ever exist repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck Co. stores. Be sure to provide atl pertinent facts when you call or visit.