Craftsman 137.219001 Operator's Manual
Craftsman 137.219001 Operator's Manual

Craftsman 137.219001 Operator's Manual

10 in drill press with laser trac


Quick Links

Operator's Manual
With Laser Trac ®
Model No. 137.219001
Before using this Drill Press,
read this manual and follow
all its Safety Rules and
Safety Instructions
Parts List
IL 60179
See the full line of Craftsman ® products
Click on the Craftsman
Club ®link and join today!
Part No. 137.219001001
Printed in China


Table of Contents

Subscribe to Our Youtube Channel

Summary of Contents for Craftsman 137.219001

  • Page 1 Parts List Operating Instructions Customer Help Line 1-800-843-1682 Sears Brands Management Corporation Hoffman Estates, IL 60179 See the full line of Craftsman ® products at Click on the Craftsman Club ®link and join today! Part No. 137.219001001 Printed in China...
  • Page 2 Sears store, Sears Parts & Repair Service Center, or other Craftsman outlet in the United States for free free repair ( or replacement if repair proves impossible). This warranty does not include expendable parts such as saw blades which can wear out from normal use within the warranty period.
  • Page 3 WARNING iCONS Your power tool and its Operator's Manual may contain "WARNING iCONS" (a picture symbol intended to alert you to and/or instruct you how to avoid a potentially hazardous condition). Understanding and heeding these symbols will help you operate your tool better and safer. Shown below are some of the symbols you may see.
  • Page 4 10. USE PROPER EXTENSION CORDS. Make sure GENERAL SAFETY INSTRUCTIONS BEFORE USING THIS POWER TOOL your extension cord is in good condition. When using an extension cord, be sure to use one heavy Safety is a combination of common sense, staying alert enough to carry the current your product will draw.
  • Page 5 17.USERECOMMENDED ACCESSORIES. 21.DONOTOVERREACH. Keepproper f ooting and Consult thisInstruction M anual forrecommended balance atalltimes. accessories. Theuseof improper accessories may causeriskof injury toyourself o r others, MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow 18.NEVER STAND ONTHETOOL.
  • Page 6 l,&WAR.I.G ] CLAMP THE WORKPIECE OR BRACE IT against the left side of the column to prevent rotation. If it is For your own safety, do not try to use your drill press or too short or the table is tilted, clamp it solidly to the plug it in until it is completely assembled and installed table and use the fence provided.
  • Page 7 23.WHEN DRILLING largediameter h oles, c lamp the 29. Drum sanders must never be operated on this drill workpiece f irmlytothetable. O therwise, thebitmay press at a speed greater than the speed rating of the grapandspintheworkpiece a thighspeeds. D O drum sander.
  • Page 8 GROUNDING INSTRUCTIONS THE EVENT OF A MALFUNCTION (When using 120 volts only) BREAKDOWN, grounding provides a path of least Ampere Rating Total Length of Cord resistance for electric current and reduces the risk of more than not more than 25ft. 50ft.
  • Page 9 RECOMMENDED ACCESSORIES UNPACKING AND CHECKING CONTENTS ,&WARNING I [,_WARNING If any partismissingor damaged, do notplugthedrill Use only accessories recommend for this drill press. press inuntil t hemissingor damaged partisreplaced, Follow instructions that accompany accessories, Use of and assembly iscomplete. ContacttheCustomer Help improper accessories may cause hazards, Lineat1-800-843-16828:30AM-5:00 PM EST Visit your Sears Hardware Department or see the Sears...
  • Page 11 Depth stopnuts Depth scalepointer Beltspeed sightwindow Motor pulley Spindle pulley Depth scale Quillreturn coil / spring Feed handle Spindle Rack ring Table bracket Belt speed sight window Table lock Pulley cover handle Bevel lock bolt Chuck key holder ", Base ON/OFF switch with Belt tension...
  • Page 12 HEADLOCKING SCREWS - Locks theheadtothe BASE- Supports d rillpress. F oradditional stability, holes areprovided inbaseto boltdrillpressto column. A LWAYS lockheadin place whileoperating the workbench. drillpress. BACKUP MATERIAL - A piece ofscrapwoodplaced ON/OFF SWITCH - Incorporates a safety switch between theworkpiece andtable. T hebackup board keywhichcanberemoved t o prevent a ccess from prevents w oodintheworkpiece f romsplintering w hen unauthorized users.
  • Page 13 ASSEMBLY INSTRUCTIONS Fig. B [ WARNING I Foryourown safety, n ever connectplugtopower sourceoutlet until a ll assemblystepsarecompleteand you have read and understoodthesafety and operating instructions. [,AWARNING I The drill pressisa heavy power tool and shouldbe lifted withthehelpoftwo PEOPLE OR MORE tosafely assemble it, ASSEMBLING...
  • Page 14 Slide this table assembly with the rack onto the Fig. F column. Engage the bottom of the rack (5) with the lip of the column support (6). Tighten the table bracket lock handle (4) to lock the table assembly to the column, NOTE: Do not overtighten.
  • Page 15 iNSTALLiNG THE CHUCK (FIG. I, J AND K) CAUTION] RISK OF PROPERTY DAMAGE. To avoid damage to [,_WARNiNG the chuck, NEVER drive the chuck on the spindle with Before any assembly or the chuck to the drill press head, a metal hammer. clean all mating surfaces with a non-petroleum based product.
  • Page 16 CHUCK KEYSTORAGE (FIG. To protect the drill press from moisture, a protective Storage holder (1) for the chuck key (2) is located on the coating has been applied to the machined surfaces. Remove this coating with a soft cloth moistened with right side of the drill press, kerosene or WD-40.
  • Page 17 [,AWARNING NOTE: DO NOT OVERTIGHTEN and restrict quill movement. To prevent personal injury, always disconnect the plug from the power source when making any adjustments. SPINDLE / QUILL (FIG. P) Rotate the feed handles counterclockwise to lower spindle to its lowest position. Hold the chuck and move Fig.
  • Page 18 [ WAR"ING 1 ,_WARNING AVOID DIRECT EYE CONTACT LASER RADIATION. Never aim the beam at a work piece with a reflective surface. Bright shiny reflective A Laser light is radiated when the laser guide is turned sheet steel or similar reflective surfaces are not on.
  • Page 19 BASIC DRILL PRESS OPERATIONS ,AWARNING ALWAYS lock the switch "OFF" when the drill press is NOTE: This machine incorporates view windows on the not in use by removing the safety switch key keep it in a pulley cover used to observe the location of the belt. safe place.
  • Page 20 Fig.X USING THEFENCE (FIG.W) Thefenceprovides a wayofaccurately a ndquickly settinguptheworkpiece f orprecision o r forrepetitive drilling operations. 1. Using a centerpunch or sharpnail,makean indentation i ntheworkpiece w hereyouwantto drill. 2. Alignthelaserlines(x)withthe indentation o nthe workpiece. 3. Loosen theknobs (1)andslide thefencebackstop(2) firmlyagainst the longsideoftheworkpiece.
  • Page 21 BASIC OPERATING INSTRUCTIONS Use the SPINDLE SPEED recommended for the Togetthebestresults andminimize thelikelihood o f speci c operation and workpiece material. Check personal injury, f ollow theseinstructions foroperating the panel on the inside pulley cover or the chart yourdrillpress. below for drilling speed information. For [ WARNING I accessories, refer to the instructions provided with each accessory.
  • Page 22 POSiTiONiNG T HETABLEANDWORKPIECE 2. Turn the laser "ON" and align the laser lines (x) with (FIG. AA AND BB) the indentation before turning the drill ON. 1. Lock the table (1) to the column (2) at a position so TILTING THE TABLE (FIG. CC) the tip of the drill bit (3) is just above the top of the NOTE: The table arm and support (1) has a predrilled workpiece (4).
  • Page 23 Fig. DD ,_ WARNING For your own safety, turn the switch OFF and remove the plug from the power source outlet before maintaining or lubricating your drill press. Frequently blow out, using an air compressor or dust vacuum, any sawdust or metal chips that accumulates inside the motor, pulley housing, table and work surface.
  • Page 24 [_WARNINGI To avoidinjury from accidental s tarting, alwaysturnswitch OFF and unplugthetool beforemoving,or making adjustments. • ConsultyourSears Service Centerif forany reasonthemotor will notrun. PROBLEM POSSIBLE CAUSES REMEDY Noisy operation 1, Incorrect belt tension, Adjust tension. See section "ASSEMBLY- TENSIONING BELT" 2. Dry spindle. 2.
  • Page 25 10 in. DRILL PRESS MODEL NO. 137.219001 WAR.I.G J When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create a HAZARD or cause product damage. WAR.I.G J Any attempt to repair or replace electrical parts on this Drill Press may create a HAZARD unless repair is done by a qualified service technician.
  • Page 26 10 in. DRILL PRESS MODEL NO. 137.219001 SCHEMATIC ..C \\'26 //83...
  • Page 27 Congratulations on making a smart purchase. Your new Craftsman ® product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That's when having a Repair Protection Agreement can save you money and aggravation.
  • Page 28 Your Home For expert troubleshooting and home solutions advice: For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-yourself.

Table of Contents