Page 1: Installation Guide
installation guide hp StorageWorks SAN switch 2/16 Product Version: V3.0.x Second Edition (February 2003) Part Number: AA-RR84B-TE This installation guide provides basic procedures for setting up, configuring, and managing the SAN switch 2/16 and 2/16 Power Pak models.
Page 2 © 2003 Hewlett-Packard Company Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Page 3: Table Of Contents
contents Contents About this Guide........... .9 Overview.
Page 4 Contents Installing the SAN Switch 2/16 ........23 Unpack and Verify Carton Contents.
Page 5 Contents Next Steps..............58 Setting QuickLoop Mode on Ports.
Page 6 Contents A Regulatory Compliance Notices ........81 FCC EMC Statement (USA) .
Page 7 Contents 13 Installing switch into the HP rack ......... . 44 14 Connecting the power cords.
Page 8 Contents hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 9: About This Guide
about this guide About this Guide This installation guide provides information to help you set up and configure the HP StorageWorks SAN Switch 2/16. About this Guide About this Guide topics include: Overview, page 10 Conventions, page 11 Rack Stability, page 14 Getting Help, page 15 hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 10: Overview
About this Guide Overview This section covers the following topics: Intended Audience Related Documentation Intended Audience This book is intended for use by customers who purchased the SAN Switch 2/16, 2/16 Power Pak; and for authorized service providers who are experienced with the following: Configuration aspects of customer Storage Area Network (SAN) fabric Customer host environments, such as Windows 2000, Windows NT, and IBM...
Page 11: Conventions
About this Guide Conventions Conventions consist of the following: Document Conventions Text Symbols Equipment Symbols Document Conventions The document conventions included in Table 1 apply in most cases. Table 1: Document Conventions Element Convention Cross-reference links Blue text: Figure 1 Key and field names, menu items, Bold buttons, and dialog box titles...
Page 12: Equipment Symbols
About this Guide Caution: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or data. Note: Text set off in this manner presents commentary, sidelights, or interesting points of information. Equipment Symbols The following equipment symbols may be found on hardware for which this guide pertains.
Page 13 About this Guide Power supplies or systems marked with these symbols indicate the presence of multiple sources of power. WARNING: To reduce the risk of personal safety from electrical shock, remove all power cords to completely disconnect power from the power supplies and systems. Any product or assembly marked with these symbols indicates that the component exceeds the recommended weight for one individual to handle safely.
Page 14: Rack Stability
About this Guide Rack Stability Rack stability protects personnel and equipment. WARNING: To reduce the risk of personal safety or damage to the equipment, be sure that: The leveling jacks are extended to the floor. The full weight of the rack rests on the leveling jacks. In single rack installations, the stabilizing feet are attached to the rack.
Page 15: Getting Help
About this Guide Getting Help If you still have a question after reading this guide, contact an HP authorized service provider or access our website: http://www.hp.com. HP Technical Support In North America, call technical support at 1-800-652-6672, available 24 hours a day, 7 days a week.
Page 16: Hp Authorized Reseller
About this Guide HP Authorized Reseller For the name of your nearest HP authorized reseller: In the United States, call 1-800-345-1518 In Canada, call 1-800-263-5868 Elsewhere, see the HP website for locations and telephone numbers: http://www.hp.com. hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 17: Overview
Overview The HP StorageWorks SAN Switch 2/16 is a high-performance, 16-port, 2 gigabit (Gb) Fibre Channel (FC) switches used to interconnect storage devices, hosts, and servers in a SAN. The hp StorageWorks SAN switch 2/16 is offered in two configurations; the 2/16 and 2/16 Power Pak.
Page 18: San Switch 2/16 Features
Overview SAN Switch 2/16 Features Read the following sections for feature-specific information. Firmware The SAN Switch 2/16 operates using Fabric Operating System firmware V3.0.2k. (version as of this writing, please refer to the switch Release Notes for exact version number). The firmware supports: High-speed data traffic using Interswitch Link (ISL) trunking technology.
Page 19: Hardware
Overview Hardware The SAN Switch 2/16 consists of the following components: A 1 Unit (U) chassis, designed for mounting in a 19-inch rack, with forced-air cooling that flows from the back of the switch to the front. 16 optical ports, compatible with Small Form Factor Pluggable media (SFPs). One RS-232 Serial port (DB9 connector) on the front panel.
Page 20: Sfp Media Side
Overview SFP Media Side The front panel of the SAN Switch 2/16 is shown in Figure 1. The front panel houses the Serial port, Ethernet port, fiber optic ports with corresponding LEDs, and the power switch LED. SHR-2548A Serial port Port speed LEDs (16) Ethernet port Port status LEDs (16)
Page 21: Isl Trunking
Overview ISL Trunking ISL trunking is a Fabric OS feature that enables distribution of traffic over the combined bandwidth of up to four ISLs between two directly adjacent switches, while preserving in-order delivery. For specific information about ISL trunking, refer to the hp StorageWorks trunking version 3.0.x/V4.0.x user guide. SFPs The ports connect to SFP media.
Page 22: Optional Hardware Kits
Overview Optional Hardware Kits HP provides the following optional hardware kits in support of the SAN Switch 2/16, see Table Table 2: SAN Switch 2/16 Orderable Hardware Accessory Part Number Short wavelength SFP A6515A* or 300834-B21** Long wavelength SFP, 10 km A6516A* or 300835-B21** 2m LC-to-LC Fibre Channel (fc) cable C7524A*...
Page 23: Installing The San Switch 2/16
Installing the SAN Switch 2/16 This chapter covers the following topics: Unpack and Verify Carton Contents, page 24 Installation and Safety Considerations, page 27 Installing the SAN Switch as a Stand-alone Unit, page 29 Installing the SAN Switch 2/16 in an HP 9000 Series or Comparable EIA Rack, page 30 Installing the Switch in the Optional HP System/e Rack, page 39...
Page 24: Unpack And Verify Carton Contents
Installing the SAN Switch 2/16 Unpack and Verify Carton Contents Unpack and inspect the SAN Switch 2/16 carton contents as follows. 1. Inspect the shipping container for possible damage caused during transit. 2. Unpack the shipping cartons. Note: The Rack Mount Kit shown in Figure 3 may not represent the kit that shipped with your switch.
Page 25: Carton Contents
Installing the SAN Switch 2/16 SHR-2489A Figure 3: Carton contents hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 26: Shipping Carton Contents
Installing the SAN Switch 2/16 Table 3: Shipping Carton Contents Item Number Description One HP StorageWorks SAN Switch 2/16 product accessory bag containing CD, license, documentation Two standard AC power cords and two PDU cords One RS-232 Serial cable (convertible to an RJ-45 connector, by removing the adapter on the end of the cable) HP StorageWorks SAN Switch 2/16...
Page 27: Installation And Safety Considerations
Installing the SAN Switch 2/16 Installation and Safety Considerations Read the following sections for installation guidelines. Install the SAN Switch 2/16 in one of the following ways: as a stand-alone unit on a flat surface, or in the HP 9000 Series (or comparable) Rack using the Rack Mount Kit supplied with the switch, contents as outlined in Table 2.
Page 28: Power Requirements
Installing the SAN Switch 2/16 Power Requirements Two AC power cords connect to the switch on the either side of the rear panel. The AC power source must meet these requirements: A properly wired, earth-grounded AC outlet Voltage capability of 85-264 VAC Input voltage frequency of 47-63 Hz Power capability of 75 watts, maximum The switch has a universal power supply capable of functioning worldwide...
Page 29: Installing The San Switch As A Stand-Alone Unit
Installing the SAN Switch 2/16 Installing the SAN Switch as a Stand-alone Unit Use these procedures for setting up the switch as a stand-alone unit. The following items are required for this setup: SAN Switch 2/16 AC power cord(s) and cables supplied with the switch Rubber mounting feet supplied with the switch 1.
Page 30: Installing The San Switch 2/16 In An Hp 9000 Series Or Comparable Eia Rack
Installing the SAN Switch 2/16 Installing the SAN Switch 2/16 in an HP 9000 Series or Comparable EIA Rack Read the following sections to install the switch in a rack using the Rack Mount Kit supplied with the switch. Obtain the following tools: A #2 Phillips screwdriver Torque screwdriver Installing the Slide Rail Assemblies to the Switch...
Page 31: Attaching The Inner Slide Rails To The Switch
Installing the SAN Switch 2/16 Attaching the Inner Slide Rails to the Switch Use the following steps to secure each inner slide rail to the switch chassis. Caution: It is important to install the inner slide rails using the Phillips head, 8-32 x 3/16”...
Page 32: Attaching The Rear Or Front Rack Mount Brackets
Installing the SAN Switch 2/16 3. Tighten the screws and torque to 15-inch pounds. SHR-2477A Figure 4: Securing the inner slide rails to the switch 4. Repeat steps 1 and 2 to attach the second inner slide rail to the switch. Make sure to orient the second inner slide rail in the same way you positioned the first (based on 1a or 1b above).
Page 33: For Rear Rack Access
Installing the SAN Switch 2/16 For Rear Rack Access Use these steps to attach the rear rack mount brackets to the switch. The rear rack mount brackets act as “stops” to prevent the switch from sliding out the rear of the rack.
Page 34: For Front Rack Access
Installing the SAN Switch 2/16 For Front Rack Access Use these steps to attach the front rack mount brackets to the switch. The front rack mount brackets act as “stops” to prevent the switch from sliding out the front of the rack. Use these steps if you installed the inner slide rails to the switch using the procedure outlined in “Attaching the Inner Slide Rails to the Switch,”...
Page 35 Installing the SAN Switch 2/16 Note: Before starting this procedure, verify that two of the slide mount L-brackets are preinstalled at the end of each outer slide rail. The L-brackets are necessary to attach the outer rails to the HP 9000 Series Rack. 1.
Page 36: Attaching The Outer Slide Rails To The Hp 9000 Series Rack
Installing the SAN Switch 2/16 Note: Position the square alignment washers onto the Phillips head 10-32 x 3/8” screws, as described in step 3. The square alignment washers are mandatory for proper switch alignment. 7. Secure each L-bracket and 3-hole bar nut to the rack’s rails with two Phillips head 10-32 x 3/8”...
Page 37: Sliding The Switch Into An Hp 9000 Series Or Eia Rack
Installing the SAN Switch 2/16 Note: Remember to position the 3-hole bar nut behind the L-bracket. 8. Tighten the screws, and torque to 25-inch pounds. 9. Repeat steps 5 through 7 to secure the other end of the outer slide rail. 10.
Page 38: Securing The Rack Mount Brackets
Installing the SAN Switch 2/16 3. Slide the switch in the rack, see Figure SHR-2476A Figure 7: Sliding the switch into an HP 9000 Series rack Securing the Rack Mount Brackets Secure the rack mount brackets (installed earlier, see “Attaching the Rear or Front Rack Mount Brackets,”...
Page 39: Installing The Switch In The Optional Hp System/E Rack
Installing the SAN Switch 2/16 Installing the Switch in the Optional HP System/e Rack This section provides instructions for installing the switch in the HP System/e rack. Items Required for the HP System/e Rack The HP System/e Rack Kit consists of the following items: HP System/e Rack Rail Kit, part number A7340-87901 Plenum, part number A7346-00001 HP System/e Rack Rail Kit Hardware, part number A7340-87902, shown next...
Page 40: Installing The Mounting Brackets
Installing the SAN Switch 2/16 Note: For proper airflow, the SFP media side of the SAN Switch 2/16 must face the rear of the rack. This mounting allows air to enter from the front of the rack and to exhaust at the rear of the rack, similar to other rack-mounted equipment. This prevents switch overheating, which may cause it to fail.
Page 41: Installing The Tinnerman Clips
Installing the SAN Switch 2/16 4. Install two M5 U-type Tinnerman clips for each of the front columns of the rack in the top and bottom positions of the three-hole pattern as shown in Figure Figure 9: Installing the tinnerman clips 5.
Page 42: Installing The Rubber Washers
Installing the SAN Switch 2/16 [1] Select this graphic frame. [2] Select File. [3] Select Import. [4] Select File. [5] Choose the appropriate graphic file name. [6] Make sure you’ve checked the Copy Into Document. [7] Select Import. Position the illustration as required. [8] Adjust the size of the outer graphic frame as required.
Page 43: Assembling The Outer Rails (Hp Rack)
Installing the SAN Switch 2/16 SHR-2560A Outer rail alignment pins M5 torx screws Figure 11: Assembling the outer rails (HP rack) 7. Assemble the two inner rails (one on each side) to the switch using (6) #8-32 x 5/16 Phillips pan-head screws, and #8 flat washer as shown in Figure Figure 12: Assembling the inner rails hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 44: Installing Switch Into The Hp Rack
Installing the SAN Switch 2/16 Caution: Do not use any other screws other than the six that are provided. Use of any longer lengths can cause damage to internal components of the switch. Before tightening screws, make sure that the rails are centered to the overall height of the switch.
Page 45: Connecting Ac Power
Installing the SAN Switch 2/16 Connecting AC Power Use these steps to power on the SAN Switch 2/16. Caution: Do not plug the power cords into the power source until the switch is completely installed in the rack. 1. Connect the switch power cords to the power connectors on the switch, see Figure SHR-2468A Figure 14: Connecting the power cords...
Page 46: Power-On Self Test
Installing the SAN Switch 2/16 3. If using the slide rail assembly kit supplied with the switch, Route the the power cord through the power cord clips. 4. Attach the other end of the power cord to a power outlet. 5.
Page 47: Checking Post Results
Installing the SAN Switch 2/16 Checking POST Results Check the success/fail results of the diagnostic tests run during POST via LED activity, the error log, or Command Line Interface (CLI) using the errShow command. For more information about error messages, refer to the hp StorageWorks fabric OS version 3.0.x/4.0.x reference guide.
Page 48: Setting Network Addresses Via A Serial Connection
Installing the SAN Switch 2/16 Setting Network Addresses via a Serial Connection Use the following steps to verify or change the switch IP address, subnetmask, or gateway address. Note: During first-time setup, you must replace the factory IP, subnetmask and gateway addresses with addresses provided by your Network Administrator.
Page 49 Installing the SAN Switch 2/16 Note: These steps show instructions specific to Hyperterminal. If using a different application, consult the specific application’s documentation. 6. Using Hyperterminal (or similar application), configure the Port Settings as follows: Bits per second: 9600 Databits: 8 Parity: None Stop bits: 1 Flow control: None...
Page 50 Installing the SAN Switch 2/16 c. To verify that the IP address was entered correctly, type: ipAddrShow d. Once the IP address is verified as correct, remove the Serial cable, and replace the shipping plug in the Serial port. Caution: The Serial port is intended only for use during the initial setting of the IP address and for service purposes.
Page 51: Connecting The Switch To The Lan
Installing the SAN Switch 2/16 Connecting the Switch to the LAN Use the following steps to connect the switch to the Ethernet Local Area Network (LAN) segment. 1. Remove the shipping plug from the Ethernet port. 2. Connect one end of an Ethernet cable to the Ethernet port, see Figure SHR-2550A Figure 16: Connecting the Ethernet cable...
Page 52: Important Information On Setting The Core Pid Format
Installing the SAN Switch 2/16 Important Information on Setting the CORE PID Format After you connect the switch via Ethernet, you must verify that all switches you intend to connect to the SAN use the same Core PID (Port Identifier) format. A PID is one of two addressing mechanisms used in Fibre Channel.
Page 53: How To Change The Core Pid Format
Installing the SAN Switch 2/16 6. To view the Core Switch PID setting, press Enter until you reach the Core Switch PID format line, similar to the following. Core Switch PID Format: (0..1) [0] Note: The [0] value shown above indicates the Core Switch PID parameter set on this particular switch.
Page 54: Modifying Domain Ids
Installing the SAN Switch 2/16 5. Locate the line, "Core Switch PID Format: (0..1) [0] 1," and select 1. 6. Press Enter until the following prompt appears. Committing configuration...Done 7. At the prompt type, SwitchEnable. 8. After setting the Core PID to match the the other switches in the fabric, see “Connecting the Switch to the Fabric”...
Page 55: Specifying Custom Status Policies
Installing the SAN Switch 2/16 6. Re-enable the switch by entering the following: switchEnable Specifying Custom Status Policies Optional. If desired, specify any custom status policies for the fabric as follows. 1. Enter the following at the prompt. switchStatusPolicySet 2. Specify the desired status policies. To completely deactivate the alarm for a particular condition, enter 0 at the prompt for that condition.
Page 56: Verifying Operation
Installing the SAN Switch 2/16 4. Connect the cables to the SFPs as appropriate to the fabric topology, by positioning each cable so that the key (the ridge on one side of the cable connector) is aligned with the slot in the SFP, see Figure SHR-2549A Figure 17: Inserting a cable into an SFP...
Page 57: Installing Multiple Switches Into An Existing San
Installing the SAN Switch 2/16 Note: Backing up the configuration is strongly recommended. This ensures that a complete configuration is available if required for a replacement switch. For instructions on how to back up the configuration, refer to “Backing Up System Configuration Settings”...
Page 58: Next Steps
Installing the SAN Switch 2/16 4. Set the switch Domain Address using the configure command to the next unused domain in the SAN. The default domain setting is 1. Note: If a switch boot failure occurs, the switch must be taken offline for repair or replacement.
Page 59: Cascading Switches
Installing the SAN Switch 2/16 device. Check the configuration information for your network components for specific requirements. See the hp StorageWorks fabric os version 3.0.x/4.0.x procedures user guide, for a detailed command description. Cascading Switches The Domain ID number uniquely identifies a switch in a fabric. Normally, the switch automatically assigns the Domain ID when a switch is first powered on or when the switch disable/enable command is executed.
Page 60 Installing the SAN Switch 2/16 hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 61: Managing The San Switch 2/16
Managing the SAN Switch 2/16 This chapter covers the following topics: Interpreting LED Activity, page 62 Management Overview, page 68 Running Basic Switch Operations Using Telnet, page 69 Diagnostic Tests, page 73 hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 62: Interpreting Led Activity
Managing the SAN Switch 2/16 Interpreting LED Activity SAN Switch 2/16 status is determined through LED activity. The LEDs will flash green, yellow, or orange while the switch is booting and while POST or other diagnostic tests are running. This is normal, and does not indicate a problem. Note: Any errors related to LED activity are listed in the error log.
Page 63: Front Panel Led Patterns During Normal Operation
Managing the SAN Switch 2/16 Table 4: Front Panel LED Patterns During Normal Operation Color Hardware Recommended Location Display Status Action Port Status LED Above Check media No light No light or signal each port, and cable. carrier (media or on left cable) is detected.
Page 64 Managing the SAN Switch 2/16 Table 4: Front Panel LED Patterns During Normal Operation (Continued) Color Hardware Recommended Location Display Status Action Port Status LED Fast-flashing The port is faulty. Reset the switch orange (continued) from a management station. Alternating Port is bypassed.
Page 65 Managing the SAN Switch 2/16 Table 4: Front Panel LED Patterns During Normal Operation (Continued) Color Hardware Recommended Location Display Status Action Power Switch Below No light Verify that the Either the switch Serial port is off, or boot is switch is on and not complete, or boot has had...
Page 66: Rear Panel Leds
Managing the SAN Switch 2/16 Rear Panel LEDs The rear panel includes the following LEDs: One power supply LED for each power supply One Port Readiness LED Table 5 describes the LEDs on the rear panel of the switch. Table 5: Rear Panel LED Patterns During Normal Operation Color Hardware Recommended...
Page 67 Managing the SAN Switch 2/16 Table 5: Rear Panel LED Patterns During Normal Operation (Continued) Color Hardware Recommended Location Display Status Action Steady green Switch is on and No action boot has required. successfully completed. Steady yellow Diagnostic If no diagnostic command is in tests are running, progress, or one...
Page 68: Management Overview
Managing the SAN Switch 2/16 Management Overview The switch is managed using TCP/IP protocol, in-band over Fibre Channel, or out-of-band by connecting to the Ethernet port. The management functions allow the administrator to monitor fabric topology, port status, physical status, and other information to aid in system debugging and performance analysis.
Page 69: Running Basic Switch Operations Using Telnet
Managing the SAN Switch 2/16 Use these steps to enable a licensed feature. 1. Log in to the switch as the admin user. 2. At the command line enter the following command: licenseAdd aaaBbbCcc (where aaaBbbCcc is the license key for a particular feature.) Note: You must enter a license key for each feature to activate.
Page 70: Changing The Admin Password And User Id
Managing the SAN Switch 2/16 Changing the Admin Password and User ID Use these steps to change the Admin user ID and password. Note: For security reasons, the first time you log into the Fabric OS you are requested to change the admin user ID and system password. 1.
Page 71: Displaying Devices Within The Fabric
Managing the SAN Switch 2/16 4. At the Ethernet Subnetmask prompt, enter the address of the subnetmask, if applicable. Press Enter to continue. 5. At the Fibre Channel IP address prompt, enter the Fibre Channel IP address for the switch. Press Enter to continue. 6.
Page 72: Displaying Switch Configuration Settings
Managing the SAN Switch 2/16 Uses these steps to set the date and time of a switch. 1. Log into the switch as the admin user. 2. At the command line enter the following command: date "MMDDhhmmYY" where: — MM is the month, valid values are 01-12. —...
Page 73: Diagnostic Tests
Managing the SAN Switch 2/16 Diagnostic Tests Read the following sections for information on using POST and diagnostic tests. Interpreting POST Results Each time the switch is powered on or reset, the switch automatically performs POST, a one minute system check during which the port status LEDs flash different colors.
Page 74 Managing the SAN Switch 2/16 hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 75: Backing Up The Configuration And Upgrading Firmware
Backing Up the Configuration and Upgrading Firmware This chapter covers the following topics: Backing Up System Configuration Settings, page 76 Upgrading or Restoring the Switch Firmware, page 78 Downloading Firmware from the HP Website, page 79 hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 76: Backing Up System Configuration Settings
Backing Up the Configuration and Upgrading Firmware Backing Up System Configuration Settings HP strongly recommends saving the configuration after the initial configuration changes and periodically thereafter. FTP must be used on Windows workstations to backup the system configuration. The FTP server must be running before an upload can occur. Use the RSHD service or FTP on a UNIX machine.
Page 77: Restoring The System Configuration Settings
Backing Up the Configuration and Upgrading Firmware Restoring the System Configuration Settings Use these steps to restore the system configuration settings from a backup. 1. Verify that the RSHD service (on a UNIX machine) or the FTP service (on a Windows or UNIX machine) is running on the host workstation.
Page 78: Upgrading Or Restoring The Switch Firmware
Backing Up the Configuration and Upgrading Firmware Upgrading or Restoring the Switch Firmware The SAN Switch 2/16 ships with preloaded firmware. In most cases, there is no need to update the firmware on the new switch. The firmware version can be determined by using: The version Telnet command The Switch Management Application page in Web Management Tools...
Page 79: Downloading Firmware From The Hp Website
Backing Up the Configuration and Upgrading Firmware Downloading Firmware from the HP Website To download the firmware from the HP website, go to http://www.hp.com/support. The website contains the required loaders and instructions for downloading the firmware to a switch. hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 80 Backing Up the Configuration and Upgrading Firmware hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 81: A Regulatory Compliance Notices
The end user of this product should be aware that any changes or modifications made to this equipment without the approval of Hewlett-Packard could result in the product not meeting the Class A limits, in which case the FCC could void the user's authority to operate the equipment.
Page 82: Emc Statement (Canada)
Regulatory Compliance Notices EMC Statement (Canada) This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la Classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. EMC Statement (European Union) This is a Class A product.
Page 83: Harmonics Conformance (Japan)
Regulatory Compliance Notices Harmonics Conformance (Japan) BSMI EMC Statement (Taiwan) RRL EMC Statement (Korea) hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 84: Laser Safety
Regulatory Compliance Notices Laser Safety A. Certification and Classification Information When equipped with native Fibre Channel adapters, this product contains a laser internal to the small form factor pluggable (SFP) transceiver modules. In the USA, the SFP module is certified as a Class 1 Laser product, conforming to the requirements contained in Department Of Health and Human Services (DHHS) regulation 21 CFR, Subchapter J.
Page 85: Battery Replacement Notice
Regulatory Compliance Notices Battery Replacement Notice Your switch is equipped with a lithium manganese dioxide, a vanadium pentoxide, or an alkaline internal battery or battery pack. There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated. Replacement is to be done by an HP authorized service provider using the HP spare designated for this product.
Page 86 Regulatory Compliance Notices hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 87: Electrostatic Discharge
Electrostatic Discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices.
Page 88: Grounding Methods
Electrostatic Discharge Grounding Methods There are several methods for grounding. Use one or more of the following methods when handling or installing electrostatic-sensitive parts: Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis. Wrist straps are flexible straps with a minimum of 1 megohm ±...
Page 89: C Technical Specifications
Technical Specifications This appendix covers the following topics: Dimensions, page 90 Power Supply Specifications, page 91 Environmental Requirements, page 92 Memory Specifications, page 93 hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 90: Dimensions
Technical Specifications Dimensions Table 6 lists SAN Switch 2/16 dimensions. Table 6: Physical Specifications Dimension Value Height 1.72 +/- 0.01 inches (4.37 +/- 0.03 cm) Depth 24.5 +/- 0.03 inches (62.2 +/- 0.1cm) Width 17 inches (43.2 cm) Weight (with both power supplies) 28.0 lbs (12.7 kg) hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 91: Power Supply Specifications
Technical Specifications Power Supply Specifications Table 7 lists power supply specifications. The power supply is universal and capable of functioning worldwide without using voltage jumpers or switches. It meets IEC 61000-4-5 surge voltage requirements. The power supply has its own built-in fan for cooling, pushing the air towards the front of the switch.
Page 92: Environmental Requirements
Technical Specifications Environmental Requirements Table 8 lists the environmental ranges that are acceptable when the switch is operating, and the acceptable ranges when the switch is not operating. Table 8: Environmental Requirements Condition Acceptable Range Temperature (operating) 10°C to 40°C Temperature (non-operating) -35°C to 65°C Humidity (operating)
Page 93: Memory Specifications
Technical Specifications Memory Specifications The switch utilizes the following memory. Main Memory (SDRAM): 32 MB per switch Flash Memory: Dual 8 MB Boot Flash: 512K bytes of 8-bit for system boot The centralized memory maximizes the overall switch throughput by guaranteeing full transmit and receive bandwidth to all Fibre Channel ports at all times.
Page 94 Technical Specifications hp StorageWorks SAN Switch 2/16 Installation Guide...
Page 95: Glossary
glossary Glossary This glossary defines terms used in this guide or related to this product and is not a comprehensive glossary of computer terms. Glossary AL_PA Arbitrated Loop Physical Address; a unique 8-bit value assigned during loop initialization to a port in an arbitrated loop. Alias Address Identifier An address identifier recognized by a port in addition to its standard identifier.
Page 96 Glossary Bandwidth The total transmission capacity of a cable, link, or system. Usually measured in bps (bits per second). May also refer to the range of transmission frequencies available to a network. See also Throughput. BB_Credit Buffer-to-buffer credit; the number of frames that can be transmitted to a directly connected recipient or within an arbitrated loop.
Page 97 Glossary Community (SNMP) A relationship between a group of SNMP managers and an SNMP agent, in which authentication, access control, and proxy characteristics are defined. See also SNMP. Connection Initiator A port that has originated a Class 1 dedicated connection and received a response from the recipient.
Page 98 Glossary EIA Rack A storage rack that meets the standards set by the Electronics Industry Association. Enabled Zone Configuration The currently enabled configuration of zones. Only one configuration can be enabled at a time. End-to-end Flow Control Governs flow of class 1 and 2 frames between N_Ports. See also EE_Credit. Error As applies to Fibre Channel, a missing or corrupted frame, time-out, loss of synchronization, or loss of signal (link errors).
Page 99 Glossary FL_Port Fabric Loop Port; a port that is able to transmit under fabric protocol and also has arbitrated loop capabilities. Can be used to connect an NL_Port to a switch. FLOGI Fabric Login; the process by which an N_Port determines whether a fabric is present, and if so, exchanges service parameters with it.
Page 100 Glossary GBps GigaBytes per second (1,062,500,000 bytes/second). Host Bus Adapter; the interface card between a server or workstation bus and the Fibre Channel network. A Fibre Channel wiring concentrator that collapses a loop topology into a physical star topology. Nodes are automatically added to the loop when active and removed when inactive.
Page 101 Glossary Loop Initialization Primitive; the signal used to begin initialization in a loop. Indicates either loop failure or resetting of a node. Looplet A set of devices connected in a loop to a port that is a member of another loop. Management Information Base;...
Page 102 Glossary Phantom Address An AL_PA value that is assigned to an device that is not physically in the loop. Also known as phantom AL_PA. A twenty-bit public address created for an 8-bit loop device to allow public devices to access it. Phantom Device A device that is not physically in an arbitrated loop, but is logically included through the use of a phantom address.
Page 103 Glossary Public Device A device that can log into the fabric and support 20-bit addresses (or has 20-bit phantom addresses created for it by the switch). Public Loop An arbitrated loop that includes a participating FL_Port, and may contain both public and private NL_Ports.
Page 104 Glossary Single Mode The fiber optic cabling standard that corresponds to distances of up to 10 km between devices. SNMP Simple Network Management Protocol. An internet management protocol that uses either IP for network-level functions and UDP for transport-level functions, or TCP/IP for both. Can be made available over other protocols, such as UDP/IP, because it does not rely on the underlying communication protocols.
Page 105 Glossary Transmission Character A 10-bit character encoded according to the rules of the 8B/10B algorithm. Transmission Word A group of four transmission characters. Trap (SNMP) The message sent by an SNMP agent to inform the SNMP management station of a critical error.
Page 106 Glossary Zone Configuration A specified set of zones. Enabling a configuration enables all zones in that configuration. Zone A set of devices and hosts attached to the same fabric and configured as being in the same zone. Devices and hosts within the same zone have access permission to others in the zone, but are not visible to any outside the zone.
Page 107: Index
index status policies configuring the IP and fibre channel address AC power connecting 51, cord connecting AC power airflow connections direction through switch E-port authorized reseller, HP FL-port automatic self-discovery F-port conventions document back panel equipment symbols description of text symbols LEDs cooling requirements backing up configuration settings...
Page 108 Index installing 30, 31, 33, 34, 38, interpreting LEDs enabling interpreting POST results enabling licensed features ISL trunking environmental requirements E-port connection equipment symbols ethernet cable L-Bracket LEDs 62, on back panel fabric OS, version Port Speed LEDs fan tray Port Status LEDs general information licensed features...
Page 109 Index POST 46, separating inner rail from outer rails power serial port maximum capability cabling pinouts requirements setting network addressing Power On Self-Test via serial port power requirements setting the IP address power supply setting the switch date and time general information SFPs specifications...
Page 110 Index websites HP storage warning weight, switch rack stability symbols on equipment web tools zoning summary hp StorageWorks SAN Switch 2/16 Installation Guide...

HP StorageWorks 2/16 - SAN Switch Installation Manual

Quick Links

Related Manuals for HP StorageWorks 2/16 - SAN Switch

Summary of Contents for HP StorageWorks 2/16 - SAN Switch

Table of Contents