Install The Water Inlet Hose - Haier XQS80-828 User Manual

Install the water inlet hose

Confirm the water faucet
Water faucet,suitable
Outlet end surface
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
water inlet hose jointer
Slider
Screw knife
Lock level
water inlet hose
Figure 1
3.Fasten the four screws evenly. See to Figure 4.
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
Figure 4
Water faucet,not suitable
Screw
Sign plate
Bushing
Figure 2 Figure 3
About 4mm before twisting
About less than 2mm after twisting
Screw nut
Figure 5
Figure 6
"WASH " button
Press the Wash button to select a wash
WASH
from the MEMORY,BLANKET,CHILD,STANDARD program.
Press SET "+ - " The button is unavailable from the COTTON programs.
The button is unavailable from the QUICK programs.
E "SPIN " button
Press the "SPIN " button to select spin procedure
from the MEMORY,BLANKET,CHILD,STANDARD program. 0-9mins
SPIN
The button is unavailable from the QUICK programs.
Press "SPIN"button then press SET
F " WATER VALUE button "
The washing machine can detect the laundries automatically. After detection, it will set the water level to suitable value
among 4, 6, 8,10 and 12 automatically.during the STANDARD program You can also set water level by yourself. After
the machine is started, it will not set water level automatically. You shall push the start/pause button to make new setting.
If there's water inside the tub, the machine cannot detect the laundries and will display water level 6 .If wet laundries
WATER
are putin, it may display water level 12. You must set suitable water level by yourself.
VALUE
During operation of soak wash and rinse program, you can push down the water level button to add water. When
you release the button, or it reaches the overflow water level, the machine will stop adding water.
The water level decided may be different from actual value because of the different moisture level of the laundries.
If Speedily program is selected, it will display water level 3 . it will per form,When RINSE it will display water level 4
After the wate level reaches 1 it will wash while water filling
When STANDARD MEMORY BLANKET CHILD and COTTON programs the rinse water value will
be one level higher than the wash water value. Besides 12 water value and select the rinse water value
by youself
G "DRYING" button
G " RYING" D " button
Push the D " RYING" button ,then the D " RYING" indicator light
DRYING program is chosen(0.5h 1.0h 2.0h).
tub, which can avoid growing mildew on the outer tub and the inner tub.
2.0h can dry laundries The max drying capacity of the fibre laundrie is 1.5 kg.
"AIR- RY"program can not be reserved D
H "RINSE" button
For the MEMORY,BLANKET,CHILD,STANDARD programs push the
then push SET "+ - " select the rinse times 0.1.2.3.
RINSE
For cotton program, press "RINSE"button
The button is unavailable from the QUICK programs.
procedure .Press SET "+ - " select the desired wash time,
.Press SET "+ - " select the desired spin time,
"+ - " button can change the process
is on, that means the " RYING" D
0.5 1.0h The purpose is drying the inner tub and the outer
RINSE botton light
then press SET "+ - " button can change the process
is flashing ,