Operation - Carrier Expressions 38CS030 Owner's Manual

The relnote control cml pertbnn the following functions:
• Turn the system ON and OFF
• Select operating mode
• Adjust room air temperature and tan speed
• Set time periods for automatic system operation
BATTERY INSTALLATION Two AAA 1.5V alkaline
batteries (included) are required for operation of the remote
control. See Fig. 2 tbr battery location.
To install batteries:
1. Remove battery compartlnent cover by sliding off of
remote.
2. Insert batteries being sure to follow polarity markings in-
side battery compartlnent.
3. Replace battery compartlnent cover.
NOTE: Replace batteries whenever "Low battery" iMicator
appears on remote control display panel.
DISPLAY SCREEN There are five operating mode indica-
tors that appear on the relnote control display screen. See Fig. 3.
OPERATION
Remote Control Operation--
The relnote control
has 3 buttons (see Fig. 4) used for operating and controlling the
system:
• MODE button changes operating mode
• UP/DOWN button selects desired operating mode
• ON/OFF button turns the system on or off and trans-
mits programing selections to unit.
BACK OF
REMOTE CONTROL
2 AAA 1,5V BATTERIES
BATTE RY COM PARTM ENT
COVER
Fig. 2 -- Location of Batteries on Remote Control
®
COOLING HEATING
&
FAN ONLY DEHUMIDIFICATION
AUTO
Fig. 3 -- Operating Mode Indicators on
Remote Control
NOTE: When translnitting a colrnnand tiom the controller to
the unit, be sure to point the controller toward the right side of
the unit. See Fig. 4. The unit wilt contirln receipt of a com-
mand by sounding 2 audible beeps.
I IMPORTANT: If no changes are made within 10 sec- I
onds, the remote control will remm to its previous
I
setting.
FAN SPEED To select the Fro1 mode and chmlge the Fro1
Speed, follow the steps below:
1. Press MODE button to select the Fan mode.
2. Press UP/DOWN button to select desired fan speed or
to Auto.
3. Press ON/OFF button to send changes to unit from re-
mote control.
NOTE: If unit is operating in DEHUMIDIFICATION mode
the fan will only operate in Low speed and cannot be changed.
TEMPERATURE SETTINGS The telnperature settings
can be easily chaalged by pointing the controller toward the unit
and pressing the UP/DOWN button until desired temperature
appears on screen. The _ symbol appears each time the ON/
OFF button is pressed.
Another way of changing the telnperamre is as follows:
1. Select the temperature display by pressthg the MODE
button. The degee sylnbol will flash next to the digits on
the screen.
2. Press UP/DOW2",rbutton to select the desired tempera-
ture. The available temperature range is tiom 54 F to
90 F.
3. Press ON/OFF button to send changes to unit tioln re-
mote control.
AIRFLOW DIRECTION Perform the following steps to
change the direction of airflow tiom the unit:
1. Press MODE button to select the Sweep fanction.
2. Press the top of the UP/DOWN button to move the air
deflector on the unit in aalup and do,a_ motion. The air-
flow sylnbol displays motion.
3. Press the bottom of the UP/DOWN button. The airflow
deflector stops at a given angle. The airflow symbol dis-
play remains in a fxed position.
4. Press ON/OFF button to seM changes to unit tiom re-
mote control.
NOTE: If placing the air deflector in a fixed position is chosen,
the deflector stops at the angle th which it was located when
the ON/OFF button was pressed.
SETTING CLOCK
1. Slide down tiont cover of controller below ON/OFF but-
ton. See FN. 4.
2. Press CLOCK button using the tip of a pen or paper clip.
See Fig. 5.
3. Press UP/DOWN button to set minutes.
4. Press MODE button. The horn digits will flash.
5. Press to UP/DOWN button to set the hour.
6. To confirm cunent clock settings, press CLOCK button
once again using the tip of a pen or paper clip. The remote
control will automatically go back to previous display
mid the clock is displayed.