Eaton Power Xpert Gateway Series 1000 Card User Manual
  1. Manuals
  2. Brands
  3. Eaton Manuals
  4. Network Card
  5. POW-R-COMMAND 1000
  6. User manual
Eaton Power Xpert Gateway Series 1000 Card User Manual

Eaton Power Xpert Gateway Series 1000 Card User Manual

Gateway series
Hide thumbs Also See for Power Xpert Gateway Series 1000 Card:
Table of Contents

Advertisement

Quick Links

Download this manual
Power Xpert Gateway Series 1000 Card
®
User's Guide

Advertisement

Table of Contents
loading

Related Manuals for Eaton Power Xpert Gateway Series 1000 Card

Summary of Contents for Eaton Power Xpert Gateway Series 1000 Card

  • Page 1 Power Xpert Gateway Series 1000 Card ® User’s Guide...
  • Page 2 Class A EMC Statements FCC Part 15 NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 3: Table Of Contents

    Table of Contents Getting Started ............Installation Checklist .
  • Page 4 TABLE OF CONTENTS Modbus Registers ........... . Modbus Register Addressing .

  • Page 5: Getting Started

    Chapter 1 Getting Started NOTE If you have completed all sections in the Power Xpert Gateway Series 1000 Card Quick Start Instructions, proceed to Chapter 2, “Configuring the Card,” on page 19. This section explains: Checklist items needed for installation Installing the card Connecting the card Verifying or assigning the IP address...
  • Page 6 GETTING STARTED Provide your local network administrator with the card’s MAC address: - MAC Address Port 1 _________________________ - MAC Address Port 2 _________________________ The MAC address for Port 1 is located on a label on top of the card. To determine the MAC address of Port 2, increase the Port 1 address by one.

  • Page 7: Installing The Card

    GETTING STARTED Installing the Card The hot-swappable PXGX Series 1000 Card can be installed without turning off the Powerware Power Distribution Unit (PDU) or ® disconnecting the load. To install the PXGX Series 1000 Card: Verify that all six DIP switches on the card are in the off position (see Figure 1).
  • Page 8 GETTING STARTED Figure 2. Install the PXGX Series 1000 Card Connect an active Ethernet cable (supplied) to the Port 1 Ethernet connector on the PXGX Series 1000 Card (see Figure 3). If you are connecting a second network connection (separate subnet), connect an active Ethernet cable (not supplied) to the Port 2 Ethernet connector on the PXGX Series 1000 Card.

  • Page 9: Connecting The Card

    GETTING STARTED Connecting the Card To connect the card to the computer and start the configuration: Plug the RJ-45 end of the supplied configuration cable into the configuration port on the card labeled “10101” (see Figure 4). NOTE Verify that you have used the port labeled “10101.” The other ports on the card do not work for configuration.
  • Page 10 GETTING STARTED Select the serial connection (such as COM1). See Figure 5. Figure 5. Select Serial Connection Set the serial line to 9600 baud, No parity, 8 data bits, 1 stop bit, and no flow control (see Figure 6). Figure 6. Configure Port Settings EATON Power Xpert ®...
  • Page 11 GETTING STARTED Verify that the PDU is turned on. After a few seconds, press Enter. The Network Settings menu appears in approximately one minute (see Figure 7). --------------------------------------------------------- ---------------- Network Settings ---------------- --------------------------------------------------------- 1. Ethernet Port 1 Settings 2. Ethernet Port 2 Settings 3.

  • Page 12: Ip Address Assignments

    GETTING STARTED IP Address Assignments Many IT managers prefer the convenience of DHCP for managing the IP addresses of networked devices. With DHCP, the IT managers can easily reassign IP addresses as the network structure changes. In some cases, DHCP may not be available, or fixed IP addresses may be preferred for the PXGX Series 1000 Card (for example, if some other networked device needs to reach the card at a fixed address).

  • Page 13: Verifying Ip Addresses (Dhcp Enabled)

    GETTING STARTED Verifying IP Addresses (DHCP Enabled) To verify the IP address assignments: Type 1 and press Enter on the Network Settings menu (see Figure 7 on page 7) to display the Network Settings: Ethernet Port 1 menu (see Figure 8). --------------------------------------------------------- ------ Network Settings: Ethernet Port 1 ------ ---------------------------------------------------------...
  • Page 14 GETTING STARTED Verify network communication by using a Web browser (see Figure 9). Type the IP address of the card and select Go. 10. The login prompt appears. The user name and default password is user for read-only information and admin for configuration (read/write) options.

  • Page 15: Assigning Ip Addresses (Dhcp Disabled)

    GETTING STARTED Assigning IP Addresses (DHCP Disabled) NOTE You can also set network settings via the PXGX Series 1000 Card’s Web page Network link (see “Network Configuration” on page 16). To manually enter fixed IP addresses for the card after you have connected it: Type 1 and press Enter on the Network Settings menu (see Figure 10) to display the Network Settings: Ethernet Port 1 menu...
  • Page 16 GETTING STARTED --------------------------------------------------------- ------ Network Settings: Ethernet Port 1 ------ --------------------------------------------------------- 1. Dynamic Addressing (DHCP) Disabled 2. IP Address [None] 3. Subnet Mask [None] 4. Default Gateway [None] MAC Address 00:60:26:10:89:A8 Link Status Enabled 0. Exit to previous menu Select an option ==> 1 Enable DHCP? (y/n): n Figure 12.
  • Page 17 GETTING STARTED Type 2 and press Enter on the Network Settings menu (see Figure 10 on page 11) to display the Network Settings: Ethernet Port 2 menu (see Figure 14). ---------------------------------------------------------- ------ Network Settings: Ethernet Port 2 ------ ---------------------------------------------------------- 1. Dynamic Addressing (DHCP) Enabled 2.
  • Page 18 GETTING STARTED 12. Type 6 and press Enter to save and apply all settings (see Figure 16). 13. Type y and press Enter to confirm that you want to save and apply all settings and exit the utility. --------------------------------------------------------- ---------------- Network Settings ---------------- --------------------------------------------------------- 1.
  • Page 19 GETTING STARTED 14. Verify network communication by using a Web browser (see Figure 17). Type the IP address of the card and select Go. 15. The login prompt appears. The user name and default password is user for read-only information and admin for configuration (read/write) options.

  • Page 20: Network Configuration

    GETTING STARTED Network Configuration If you know the card’s IP address, you can configure the network settings from the card’s Web page: Open a Web browser, type the IP address of the card, and select The login prompt appears. The user name and default password is user for read-only information and admin for configuration (read/write) options.
  • Page 21 GETTING STARTED If you will be using host names for controlling access to the card, enter the Domain, as well as the DNS IP addresses in the Nameserver fields. If you will be using Simple Network Management Protocol (SNMP), identify the physical location of the installed PDU/card (sysLocation string) in the System location field.
  • Page 22 GETTING STARTED EATON Power Xpert ® Gateway Series 1000 Card User’s Guide 164201670 Rev 1...

  • Page 23: Configuring The Card

    Chapter 2 Configuring the Card NOTE If DHCP is disabled and you will be using host names for servers, such as the mail server, Network Time Protocol (NTP) server, SNMP hosts, Modbus /TCP hosts, or trap ® recipients, enter the IP address of your network DNS Server (see “Network Configuration” on page 16).

  • Page 24: Changing The Passwords

    CONFIGURING THE CARD Changing the Passwords The user name and default password is user for read-only information and admin for configuration (read/write) options. To change the passwords: From the card’s Web page, click the Access Control link from the menu bar. To change the user password, enter the new password in the ’user’...

  • Page 25: Setting The Date And Time

    CONFIGURING THE CARD Setting the Date and Time NOTE All selections are automatically converted to Coordinated Universal Time (UTC). To set the date and time: From the card’s Web page, click the Date/Time link from the menu bar. The default is to synchronize the date and time from the PC clock. To synchronize the card with Network Time Protocol servers, select Synchronize with NTP server(s) and type the IP addresses or host names.

  • Page 26: Configuring Snmp Options

    CONFIGURING THE CARD To customize how the date appears in the card’s data and event logs, select a Date format for logs option (mm/dd/yyyy, dd/mm/yyyy, yyyy-mm-dd, or dd mmm yyyy). The default is mm/dd/yyyy. To select the time zone for the card, specify the Timezone for Logs, email, and connected device.

  • Page 27: Restricting Snmp Access

    CONFIGURING THE CARD Click Apply and then OK to save the settings. Repeat Steps 3 and 4 for each additional trap recipient. To remove a trap recipient, click Delete Last. Click OK when prompted to remove the settings for the trap recipient entered last. Restricting SNMP Access To limit access to the card from trusted SNMP NMS hosts only: From the card’s Web page, click the Access Control link from the...

  • Page 28: Management From An Snmp Nms

    CONFIGURING THE CARD Management from an SNMP NMS To access the PXGX Series 1000 Card via SNMP: Use these default Community strings: GET Community string: public SET Community string: private From the card’s Web page, click the Documentation link from the menu bar (or visit www.eaton.com/powerxpert) for the following MIB files for the PXGX Series 1000 Card: MIB Name...

  • Page 29: Configuring Modbus Tcp/Ip Options

    CONFIGURING THE CARD Configuring Modbus TCP/IP Options To limit access to the card from trusted Modbus TCP/IP addresses only: From the card’s Web page, click the Access Control link from the menu bar. Activate the check box for Modbus-TCP access restricted by IP/hostname.

  • Page 30: Configuring E-Mail Notification

    CONFIGURING THE CARD Configuring E-mail Notification You may use the PXGX Series 1000 Card to inform selected e-mail accounts of events and changes in status as they occur in the PDU or to provide a status message at a predetermined time. To configure e-mail notification: From the card’s Web page, click the Email link from the menu bar.
  • Page 31 CONFIGURING THE CARD The e-mail Recipients are numbered. Select a number for a recipient. You can select different options for each recipient (Steps 6 through 10). After you enter and save an e-mail address, the Recipients list updates to show the recipient number and the corresponding e-mail address.

  • Page 32: Configuring Emp Settings

    CONFIGURING THE CARD Configuring EMP Settings NOTE Verify that the Power Xpert Gateway Card DIP switch #2 is set to the ON position, enabling the card for communication with an EMP. To configure the EMP settings: From the card’s Web page, click the Environmental Monitoring Probe link from the menu bar.

  • Page 33: Configuring Auto Discovery Settings

    CONFIGURING THE CARD Configuring Auto Discovery Settings Configure the Auto Discovery settings so that the Power Xpert Software can find the PXGX Series 1000 Card on the network automatically. The card sends multicast discovery messages to any control Power Xpert host monitoring the specified Listen port.
  • Page 34 CONFIGURING THE CARD EATON Power Xpert ® Gateway Series 1000 Card User’s Guide 164201670 Rev 1...

  • Page 35: Root Certificate Authority Installation

    Chapter 3 Root Certificate Authority Installation Improve the security of your PXGX Series 1000 Card on the Web by installing a root certificate authority (CA). A CA is a trusted third-party organization that issues digital certificates for use with encrypted digital transactions.

  • Page 36: Installing Root Ca With Microsoft Internet Explorer 6

    ROOT CERTIFICATE AUTHORITY INSTALLATION Installing Root CA with Microsoft Internet Explorer 6 To install a certificate for the PXGX Series 1000 Card with Microsoft Internet Explorer 6: Open the browser, type the IP address of the card in the address bar, and select Go.
  • Page 37 ROOT CERTIFICATE AUTHORITY INSTALLATION Click the View Certificate button. The Certificate window opens (see Figure 20). Figure 20. Certificate Window NOTE The certificate cannot be verified yet because it is issued by a nontrusted CA. EATON Power Xpert ® Gateway Series 1000 Card User’s Guide 164201670 Rev 1...
  • Page 38 ROOT CERTIFICATE AUTHORITY INSTALLATION Select the Certification Path tab. The root CA is displayed as “Power Xpert Gateway Card” and the issued certificate is shown as the device’s IP address (see Figure 21). Select Power Xpert Gateway Card. Figure 21. Certification Path Window EATON Power Xpert ®...
  • Page 39 ROOT CERTIFICATE AUTHORITY INSTALLATION Click View Certificate. A new Certificate window opens for the CA (see Figure 22). Figure 22. Certification Window for the Power Xpert Gateway Card EATON Power Xpert ® Gateway Series 1000 Card User’s Guide 164201670 Rev 1...
  • Page 40 ROOT CERTIFICATE AUTHORITY INSTALLATION Click Install Certificate..The Certificate Import Wizard window opens (see Figure 23). Figure 23. Certificate Import Wizard EATON Power Xpert ® Gateway Series 1000 Card User’s Guide 164201670 Rev 1...
  • Page 41 ROOT CERTIFICATE AUTHORITY INSTALLATION Click Next. The Certificate Store window opens, prompting you to specify a certificate store (see Figure 24). Figure 24. Certificate Store Window EATON Power Xpert ® Gateway Series 1000 Card User’s Guide 164201670 Rev 1...
  • Page 42 ROOT CERTIFICATE AUTHORITY INSTALLATION Verify that the default setting, Automatically select the certificate store ..., is selected. Click Next. The certificate wizard displays a final verification (see Figure 25). Figure 25. Verifying the Certificate Import Settings 10. Click Finish to complete the wizard. A message box similar to Figure 26 opens: Figure 26.
  • Page 43 ROOT CERTIFICATE AUTHORITY INSTALLATION 11. Click Yes to install the CA. A new dialog box window opens to verify that the import was successful. 12. Close all windows except for the original Security Alert window (see Figure 19 on page 32). 13.

  • Page 44: Installing Root Ca With Microsoft Internet Explorer 7

    ROOT CERTIFICATE AUTHORITY INSTALLATION Installing Root CA with Microsoft Internet Explorer 7 To install a certificate for the PXGX Series 1000 Card with Microsoft Internet Explorer 7: Open the browser and type the IP address of the card followed by the path “/ca.html”...
  • Page 45 ROOT CERTIFICATE AUTHORITY INSTALLATION Click Root CA Certificate. A File Download warning window opens (see Figure 29). Figure 29. File Download Warning Click Open. The Certificate Window opens (see Figure 20 on page 33). Follow the remaining steps for using Internet Explorer 6 (Step 3 on page 34 through Step 15 on page 39).

  • Page 46: Installing Root Ca With Mozilla Firefox

    ROOT CERTIFICATE AUTHORITY INSTALLATION Installing Root CA with Mozilla Firefox To install a certificate for the PXGX Series 1000 Card with Mozilla Firefox: Open the browser and type the IP address of the card followed by the path “/ca.html” in the address bar. For example: http://10.222.51.236/ca.html The following window displays (see Figure 30): Figure 30.
  • Page 47 ROOT CERTIFICATE AUTHORITY INSTALLATION Click Root CA Certificate. Firefox opens the Downloading Certificate window (see Figure 31). Figure 31. Downloading Certificate Window If desired, click View to manually examine the contents of the certificate. Click the Trust this CA to identify web sites check box option. Click OK to complete the installation process.
  • Page 48 ROOT CERTIFICATE AUTHORITY INSTALLATION EATON Power Xpert ® Gateway Series 1000 Card User’s Guide 164201670 Rev 1...

  • Page 49: Mib Files

    Chapter 4 MIB Files This chapter describes the Management Information Base (MIB) files available with the card. A MIB is an information repository residing on a device in a communication network. Network management software uses a device’s MIB to manage the device. Every manageable device on a network has a MIB consisting of one or more files that list information about the device.

  • Page 50: Eaton Pdu Mib

    MIB FILES Eaton PDU MIB The Eaton PDU MIB module contains objects and notifications for PDU, Panel, and Breaker information levels: mainPDU pduPanel pduBreaker mainPDU Objects in this group describe the main PDU in the system. This group has three subgroups: Nameplate Ratings subgroup.

  • Page 51: Eaton Emp Mib

    MIB FILES Eaton EMP MIB Objects in this group are provided by the EMP and include temperature and humidity readings, alarming limits, the two contacts readings, and setup information. The group contains a table of values for environmental contact sensing (normally two digital inputs for monitoring all contacts).
  • Page 52 MIB FILES EATON Power Xpert ® Gateway Series 1000 Card User’s Guide 164201670 Rev 1...

  • Page 53: Modbus Registers

    Chapter 5 Modbus Registers This chapter describes how to address a specific Power Distribution Unit (PDU) or Remote Power Panel (RPP), a specific panel in a PDU or RPP, and a specific breaker in a panel using Modbus TCP/IP. NOTE To obtain the panel or circuit breaker data, the PDU/RPP must have the Energy Management System (EMS) Level 3 option installed.

  • Page 54: Modbus Register Addressing

    MODBUS REGISTERS Modbus Register Addressing This section describes Modbus function codes, data formats, and data addressing. Modbus Function Codes The PDU/RPP registers are read using Modbus Function Codes (FC). For most PDU/RPP registers, FC 04 is used. The PDU/RPP supports the following hex function codes: Table 1.

  • Page 55: Data Addressing

    MODBUS REGISTERS TIME – The Time type (ymdhms) consists of six bytes specifying the year, month, day, hour, minutes, and seconds. The bytes are stored in hexadecimal format. If your Modbus application displays the individual bytes in a register, view the bytes using the decimal option. Otherwise, the bytes are best viewed by displaying the two-byte register in a binary format and translating each byte to decimal.

  • Page 56: Pdu/Rpp Unit Id Numbers

    MODBUS REGISTERS PDU/RPP Unit ID Numbers Because the PDU/RPP consists of several panels of circuit breakers, set the Unit ID in the Modbus program to specify a specific PDU/RPP, a specific panel, or a specific breaker (see Table 2). The PDU/RPP has a Unit ID of 0, 1, or 255. The same PDU/RPP information can be obtained from any of these IDs.
  • Page 57 MODBUS REGISTERS Table 2. PDU/RPP Unit ID Numbers (continued) Unit ID Description Panel #12 Summary Data Panel #13 Summary Data Panel #14 Summary Data Panel #15 Summary Data Panel #16 Summary Data Panel #1 Breaker Data Panel #2 Breaker Data Panel #3 Breaker Data Panel #4 Breaker Data Panel #5 Breaker Data...

  • Page 58: Pdu/Rpp Registers And Alarms

    MODBUS REGISTERS PDU/RPP Registers and Alarms This section contains information for the PDU/RPP Registers (FC 04) and PDU/RPP Alarms (FC 02). PDU/RPP Registers (FC 04) To read the vendor name in the PDU/RPP, set the Modbus program to Unit ID 1 and register 1001: IP: <IP address of PDU/RPP>...
  • Page 59 MODBUS REGISTERS Table 3. PDU/RPP Registers (FC 04) (continued) Name Register Data Type Bytes Number of Phases 1208 UINT Parallel System Flag 1209 UINT Number of Controlled Banks 1210 UINT Device Topology 1211 UINT Asset ID 1324 STRING Number of Panels 1453 UINT Status...
  • Page 60 MODBUS REGISTERS Table 3. PDU/RPP Registers (FC 04) (continued) Name Register Data Type Bytes AC V ratio C out 4164 FLOAT AC I Gnd 5008 FLOAT AC I in A 5022 FLOAT AC I in B 5024 FLOAT AC I in C 5026 FLOAT AC I out A...

  • Page 61: Pdu/Rpp Alarms (Fc 02)

    MODBUS REGISTERS Table 3. PDU/RPP Registers (FC 04) (continued) Name Register Data Type Bytes I A out THD 8014 FLOAT I B out THD 8016 FLOAT I C out THD 8018 FLOAT VA in THD 8042 FLOAT VB in THD 8044 FLOAT VC in THD...
  • Page 62 MODBUS REGISTERS Table 4. PDU/RPP Alarms (FC 02) Name Register Data Type AC Input Over Volts 1006 BOOL AC Input Under Volts 1007 BOOL Input Frequency Fault 1008 BOOL AC Output Over Volts 1009 BOOL AC Output Under Volts 1010 BOOL AC Output Frequency Fault 1011...
  • Page 63 MODBUS REGISTERS Table 4. PDU/RPP Alarms (FC 02) (continued) Name Register Data Type System Alarm Active 1186 BOOL Inverter Rotation 1192 BOOL Invalid Board ID 1195 BOOL Output Watts Overload 1197 BOOL Xformer Over Temp Warning 1210 BOOL Input THD High A 1212 BOOL Input THD High B...

  • Page 64: Panel Registers And Alarms

    MODBUS REGISTERS Table 4. PDU/RPP Alarms (FC 02) (continued) Name Register Data Type Branch Breaker Overload Warning 1249 BOOL Branch Breaker Overload 1250 BOOL Branch Breaker Disconnected 1252 BOOL Main Breaker Overload Warning 1253 BOOL Main Breaker Overload 1254 BOOL Primary Breaker Open 1256 BOOL...
  • Page 65 MODBUS REGISTERS For example, the AC Voltage between Phase A and Neutral is available in register 4010. To read the AC Voltage in Phase A at Panel #1, set the Modbus program to Unit ID 2 and register 4010: IP: <IP address of PDU/RPP> Unit ID: 2 Starting Register: 4010 Number of Registers: 2...
  • Page 66 MODBUS REGISTERS Table 5. Panel Summary Registers (FC 04) (continued) Name Register Data Type Bytes AC V AN 4010 FLOAT AC V BN 4012 FLOAT AC V CN 4014 FLOAT AC V MAX AN 4296 FLOAT AC V MAX BN 4298 FLOAT AC V MAX CN...

  • Page 67: Panel Alarms (Fc 01 Or 02)

    MODBUS REGISTERS Table 5. Panel Summary Registers (FC 04) (continued) Name Register Data Type Bytes MIN Frequency 11022 FLOAT MAX Frequency 11027 FLOAT Panel Alarms (FC 01 or 02) Table 6 lists the panel alarms. They are not registers, but are discrete inputs and are read using FC 01 or FC 02.

  • Page 68: Breaker Data And Alarms

    MODBUS REGISTERS Breaker Data and Alarms This section contains: Names of breaker parameters along with the register numbers for Breaker #1 Instructions for calculating the register numbers for other breakers Breaker alarms Breaker #1 Data Registers (FC 04) To specify a specific breaker, use a Unit ID for breaker data along with the register number for the specific breaker.
  • Page 69 MODBUS REGISTERS Table 7. Breaker #1 Data Registers (FC 04) (continued) Name Register Data Type Bytes AC MAX Current Phase C 1047 FLOAT Percent FL Current A 1049 FLOAT Percent FL Current B 1051 FLOAT Percent FL Current C 1053 FLOAT Watts Phase A 1055...

  • Page 70: Calculating Breaker Register Numbers

    MODBUS REGISTERS Calculating Breaker Register Numbers Table 7 shows the register numbers for Breaker #1. There can be many breakers in a panel. Determine the corresponding register numbers for other breakers in the panel by using the following formula: Breaker register # = Breaker #1 register + ((Breaker # – 1) x 200)) For example: Breaker #2 starts at 1200: 1000 + ((2 –...

  • Page 71: Breaker Alarms (Fc 01 Or 02)

    MODBUS REGISTERS Breaker Alarms (FC 01 or 02) There are two alarms for each circuit breaker: Overload Warning and Overload. Each alarm has a unique address similar to the data registers, but these alarms are not data registers. The alarms are discrete inputs and are read using FC 01 or FC 02 in the Modbus program.

  • Page 72: Environmental Monitoring Probe (Fc 03 Or 04)

    MODBUS REGISTERS Environmental Monitoring Probe (FC 03 or 04) The optional Environmental Monitoring Probe for the PDU/RPP can measure temperature and humidity. Because the device can be located outside the PDU/RPP, the reference is to “auxiliary” data. In addition, it contains two connections for monitoring the condition of auxiliary input contacts, such as a door switch.

  • Page 73: Specifications

    Chapter 6 Specifications Table 10. Technical Specifications Atmel AT91RM9200 ARM-9 Memory 32 MB Static DRAM 32 MB Flash ROM LAN Controller AT91RM9200 Integrated – Port 1 SMSC LAN91C113I – Port 2 Network Connection (2) 10/100BaseT RJ-45 network connectors PDU Protocol Powerware Power Distribution Unit (PDU) communication protocol Network Protocols SNMP v1 over UDP/IP...
  • Page 74 SPECIFICATIONS EATON Power Xpert ® Gateway Series 1000 Card User’s Guide 164201670 Rev 1...

  • Page 75: Operation And Maintenance

    Chapter 7 Operation and Maintenance This section explains: Indicator descriptions DIP switch settings Generating log files Firmware upgrade instructions Front-Panel Indicator Descriptions The Ethernet port indicator descriptions for the PXGX Series 1000 Card are listed in Table 11; the stacked indicator descriptions are listed in Table 12.
  • Page 76 OPERATION AND MAINTENANCE Table 12. Stacked Indicator Descriptions Label Color Illuminated Not Illuminated STATUS Green Communication with the PDU has been Communication with the PDU has not established. been established. As the card boots, the indicator remains off. However, if it remains off after one minute, there is a communication problem between the card and the PDU.

  • Page 77: Dip Switch Description

    OPERATION AND MAINTENANCE DIP Switch Description DIP switch definitions for the PXGX Series 1000 Card are listed in Table 13. Table 13. DIP Switch Definitions S1 Position OFF Position (Default) ON Position Number Enable previously stored network Override network settings to configuration settings (Normal assign private IP addresses mode)

  • Page 78: Generating Log Files

    OPERATION AND MAINTENANCE Generating Log Files NOTE The data log and event log files are comma-separated values (*.csv) files that can be opened in Microsoft Excel software. Some computer configurations will automatically open the files in the Microsoft Excel software instead of prompting you to save. To generate a data log: From the card’s Web page, click the Data Log link from the menu bar.

  • Page 79: Service And Support

    Chapter 8 Service and Support If you have any questions or problems with the PXGX Series 1000 Card, call your Local Distributor or the Help Desk at one of the following telephone numbers and ask for a PXGX Series 1000 Card technical representative.

  • Page 80: Two-Year Limited Warranty (Us And Canada)

    Two-Year Limited Warranty (US and Canada) Power Xpert Gateway (PXGX) Series 1000 and Series 2000 Cards WARRANTOR: The warrantor for the limited warranties set forth herein is Eaton Electrical Inc., a Delaware Corporation company (“Company”). LIMITED WARRANTY: This limited warranty (this “Warranty”) applies only to the original End-User (the “End-User”) of the Power Xpert Gateway (PXGX) Series 1000 or Series 2000 Card (the “Product”) purchased on or after June 1,...
  • Page 81 SERVICE AND SUPPORT Company shall not be responsible for any charges for testing, checking, removal or installation of Warranted Items. COMPANY DOES NOT WARRANT EQUIPMENT NOT MANUFACTURED BY COMPANY. IF PERMITTED BY THE APPLICABLE MANUFACTURER, COMPANY SHALL PASS THROUGH SUCH MANUFACTURER’S WARRANTIES TO END-USER.
  • Page 82 SERVICE AND SUPPORT EATON Power Xpert ® Gateway Series 1000 Card User’s Guide 164201670 Rev 1...
  • Page 84 *1642016701* 164201670 1...

Table of Contents