HP rp4410 Installation Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Server
  5. rp4410
  6. Installation manual
HP rp4410 Installation Manual

HP rp4410 Installation Manual

Installation guide, sixth edition - hp 9000 rp4410/rp4440
Hide thumbs Also See for rp4410:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, Manual

Installation Guide

HP 9000 rp4410 and HP 9000 rp4440
Manufacturing Part Number: A9950-96010
Six Edition
April 2007
Printed in the US

Advertisement

Table of Contents
loading

Related Manuals for HP rp4410

Summary of Contents for HP rp4410

  • Page 1: Installation Guide

    Installation Guide HP 9000 rp4410 and HP 9000 rp4440 Manufacturing Part Number: A9950-96010 Six Edition April 2007 Printed in the US...

  • Page 2: Legal Notices

    Legal Notices Copyright Notices. © Copyright 2007 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.

  • Page 3: Table Of Contents

    Contents 1. Installing the System Introduction ............... . 13 Server Views.
  • Page 4 Contents Connecting to the LAN ............. . 74 Console Setup .
  • Page 5 Tables Table 1. Publishing History Details ..........10 Table 2.
  • Page 6 Tables...
  • Page 7 Figure 1-3. HP 9000 rp4410 and rp4440 Servers (Rear View) ......15...
  • Page 8 Figures Figure 1-44. Front Control Panel LEDs ..........95 Figure 1-45.

  • Page 9: About This Document

    About This Document This document describes how to unpack the HP 9000 rp4410 and HP 9000 rp4440 server, install additional components, start a server console session, power on the server, and boot the operating system. The document printing date and part number indicate the document’s current edition. The printing date changes when a new edition is printed.

  • Page 10: Table 1. Publishing History Details

    Operating Systems Manufacturing Supported Product Versions Publication Date Supported Part Number A9950-96010 HP-UX 11i v1 HP 9000 rp4410 and rp4440 April 2007 HP-UX 11i v2 HP-UX 11i v3 A9950-96005 HP-UX 11i v1 HP 9000 rp4410 and rp4440 April 2005 HP-UX 11i v1...

  • Page 11: Table 2. Hp-Ux 11I Releases

    IMPORTANT Important messages provide essential information to explain a concept or to complete a task. A note highlights useful information such as restrictions, recommendations, or important NOTE details about HP product features. Tips provide you with helpful hints for completing a task. A tip is not used to give essential information, but can be used, for example, to provide an alternate method for completing the task that precedes it.

  • Page 12: Related Documents

    Related Documents You can find other information on HP server hardware management and diagnostic support tools in the following publications. Web Site for HP Technical Documentation: http://docs.hp.com Server Hardware Information: http://docs.hp.com/en/hw.html Diagnostics and Event Monitoring: Hardware Support Tools Complete information about HP’s hardware support tools, including online and offline diagnostics and event monitoring tools can be found on the Web at: http://docs.hp.com/hpux/diag/ This site has manuals, tutorials, FAQs, and other reference material.

  • Page 13: Installing The System

    “Troubleshooting” on page 91 Introduction The HP 9000 rp4410 and rp4440 servers are 1P/1C, 1P/2C, 2P/2C, 3P/2C, or 4P/2C servers based on the PA-RISC processor family architecture. The server accommodates up to 32 DIMMs and internal peripherals including hard disks and a DVD drive. Its high availability features include hot-swappable fans, hot-swappable power supplies, hot-pluggable disk drives, and hot-pluggable PCI-X cards.

  • Page 14: Server Views

    Installing the System Server Views Server Views Figure 1-1, Figure 1-2, and Figure 1-3 show the top, front, and rear views of the HP 9000 rp4410 and rp4440 servers. Figure 1-1 HP 9000 rp4410 and rp4440 Servers (Top View) Chapter 1...

  • Page 15: Detailed Server Description

    Figure 1-3 HP 9000 rp4410 and rp4440 Servers (Rear View) Detailed Server Description The following sections list information on the main subsystems within the HP 9000 rp4410 and rp4440 servers. I/O Subsystem The following is supported on the HP 9000 rp4410 and rp4440 servers: •...

  • Page 16: Processors

    Both processors are available with 32 MB or 64 MB L2 cache per dual processor module. • HP 9000 rp4410 server can have one processor or both processors of a single dual processor module enabled, or two processors enabled in each of two dual processor modules.

  • Page 17: Cooling

    Requires that DIMMs within each group of four (quad) be identical. Cooling Six cooling fans with N+1 redundancy. Power Supply Unit The following is supported on the HP 9000 rp4410 and rp4440 servers: • One 1200 W hot-swappable power supply. •...

  • Page 18: Dimensions And Values

    Integrity iLO MP interprets and stores event IDs. Reviewing these events helps you diagnose and troubleshoot problems with the server. Dimensions and Values Table 1-1 lists the dimensions and their values of the HP 9000 rp4410 and rp4440 servers. Table 1-1 Server Dimensions and Values...

  • Page 19: Installation Sequence And Checklist

    Installing the System Installation Sequence and Checklist Ensure that the system is powered off and all power sources are disconnected from WARNING the server prior to removing or installing server hardware unless you are removing or installing a hot-swappable or hot-pluggable component. Voltages are present at various locations within the server whenever a dc power source is connected.

  • Page 20: Unpacking And Inspecting The Server

    Installing the System Unpacking and Inspecting the Server Unpacking and Inspecting the Server This section describes procedures you perform before installation. Ensure that you have adequately prepared your environment for the new server, received the components that you ordered, and verified that the server and its containers are in good condition after shipment.

  • Page 21: Returning Damaged Equipment

    Installing the System Installing Additional Components Returning Damaged Equipment If the equipment is damaged, contact your HP customer service representative immediately. The service representative initiates appropriate action through the transport carrier or the factory and assists you in returning the equipment. Unloading the Server with a Lifter Use caution when using a lifter.

  • Page 22: Accessing A Rack-Mounted Server

    Installing Additional Components Accessing a Rack-Mounted Server The HP 9000 rp4410 and rp4440 servers are designed to be rack mounted. The following procedure explains how to gain access to a server that is mounted in an approved rack. Ensure that all antitip features are employed prior to extending the server (front WARNING and rear antitip feet installed;...

  • Page 23: Accessing A Pedestal-Mounted Server

    Accessing a Pedestal-Mounted Server The HP 9000 rp4410 and rp4440 servers are also designed to be mounted in a pedestal (rackless). You do not need to remove the pedestal from the server to gain access to internal components. The front bezel, front cover, and top cover can be removed with the pedestal attached to the server.

  • Page 24: Front Panel Controls And Indicators

    Installing the System Installing Additional Components Front Panel Controls and Indicators The front panel of the server provides controls and indicators used for common operations. Figure 1-6, Figure 1-7, and Figure 1-8 show the front view of the server and the control panel. Figure 1-6 Front View with Bezel Control Panel...

  • Page 25: Table 1-3. Control Panel Led Definitions

    Installing the System Installing Additional Components Figure 1-8 Control Panel System LED Power LED Power Button Disk LED TOC/NMI Button Thermal LED Locator Button/LED Table 1-3 and Table 1-4 list the control panel LED and the switch and button LED status and descriptions. Table 1-3 Control Panel LED Definitions LED/ Button...

  • Page 26: Table 1-4. Switch And Button Led Definitions

    Momentarily (less than one second) has no effect. • More than one second, but less than five seconds—do not use. This initiates e-buzzer functions that are not supported in the HP 9000 rp4410 and rp4440 servers. • More than five seconds then released causes an immediate hard power off.

  • Page 27: Additional Controls And Indicators

    Installing the System Installing Additional Components Additional Controls and Indicators Storage devices have additional LEDs showing their status. Hot-Pluggable Disk Drive Indicators The hot-pluggable disk drives have two LEDs per drive, as follows: Figure 1-9 and Table 1-5 show the hot-pluggable disk drive LED indicators and definitions. Figure 1-9 Hot-Pluggable Disk Drive LED Indicators Status LED...

  • Page 28: Front Bezel

    Installing the System Installing Additional Components Figure 1-10 DVD or CD-RW/DVD LED Indicators Activity LED Eject Button Emergency Eject Table 1-6 DVD Drive LED Definitions State Description Activity LED Flashing green Drive is active Front Bezel The server does not need to be powered off to remove the front bezel. Removing the Front Bezel To remove the front bezel, grasp the front bezel at the outer edges and pull straight out.

  • Page 29: Front And Top Covers

    Installing the System Installing Additional Components The front control panel access door is on the bezel. Opening the control panel door provides access to the following components: • Power button • System LEDs Replacing the Front Bezel To replace the front bezel, hold the bezel in mounting position and push the bezel straight into the chassis until it snaps into place.

  • Page 30: Figure 1-12 Removing And Replacing The Front Cover

    Installing the System Installing Additional Components Figure 1-12 Removing and Replacing the Front Cover Thumbscrews Step 4. Raise the cover slightly, and pull the cover toward the front of the server to free the tabs from the slots in the center of the chassis. Replacing the Front Cover To replace the front cover, follow these steps: Step 1.

  • Page 31: Figure 1-13 Removing And Replacing The Top Cover

    Installing the System Installing Additional Components Figure 1-13 Removing and Replacing the Top Cover Thumbscrews Rear of Chassis Replacing the Top Cover To replace the top cover, follow these steps: Step 1. Align the tabs at the rear of the top cover with the corresponding slots in the chassis. Fully seat the tabs into the slots and push forward until it seats.

  • Page 32: Hot-Swappable Chassis Fan Units

    Installing the System Installing Additional Components Hot-Swappable Chassis Fan Units There are three hot-swappable chassis fan units in the server. • Fan units 0, 1, and 2 are in the center of the chassis, spanning the full chassis width. • Fan units 0 and 1 are interchangeable and are in the left and center positions.

  • Page 33: Figure 1-15. Hot-Swappable Power Supply Fan (Unit 2)

    Installing the System Installing Additional Components Figure 1-15 Hot-Swappable Power Supply Fan (Unit 2) Observe all ESD safety precautions before attempting this procedure. Failure to follow ESD CAUTION safety precautions can result in damage to the server. NOTE A hot-swappable device does not require interaction with the operating system before the device is removed from or installed into the server.

  • Page 34: I/O Baseboard Assembly

    Installing the System Installing Additional Components Step 1. If rack-mounted, slide the server out from the rack until it stops. (See “Extend the Server from the Rack” on page 22.) Step 2. Remove the top cover. (See “Removing the Top Cover” on page 30.) Step 3.
  • Page 35 Installing the System Installing Additional Components Removing the I/O Baseboard Assembly Before removing the I/O baseboard assembly, record all boot configuration settings displayed by CAUTION the BCH INFO ALL command. These values might need to be reset after replacing the I/O baseboard assembly.

  • Page 36: Figure 1-16 I/O Baseboard Locking Lever

    Installing the System Installing Additional Components Figure 1-16 I/O Baseboard Locking Lever OPEN CLOSE Step 7. Slide the system I/O baseboard assembly all the way to the rear until removed from chassis. CAUTION The I/O baseboard assembly is large. Be careful when lifting it out of the server chassis.

  • Page 37: Figure 1-17 I/O Baseboard Assembly Removal

    Installing the System Installing Additional Components Figure 1-17 I/O Baseboard Assembly Removal Replacing the I/O Baseboard Assembly The I/O baseboard assembly replacement procedure assumes that you are reinstalling the NOTE assembly that was previously removed from a configured server. To replace the I/O baseboard assembly, follow these steps: Step 1.

  • Page 38: System Battery

    Installing the System Installing Additional Components System Battery This section provides information on the system battery and how to replace a system battery. Battery Notice This product contains a Lithium battery (HP part number 1420-0386). WARNING Lithium batteries can explode if mistreated. Do not recharge, disassemble, or dispose of lithium batteries in a fire.

  • Page 39: Figure 1-18 System Battery Location On I/O Baseboard

    Installing the System Installing Additional Components Figure 1-18 System Battery Location on I/O Baseboard Battery Step 5. Lift up the battery holder retaining clip with a flat-head screwdriver and push on the back of the battery to remove the battery from its socket. Step 6.

  • Page 40: Installing Power Supplies And Disk Drives

    Installing Power Supplies and Disk Drives This section provides information about installing hot-swappable power supplies and hot-pluggable disk drives. Hot-swappable power supplies are located at the rear of the HP 9000 rp4410 and rp4440 servers, and hot-pluggable disk drives are located behind the front bezels.

  • Page 41: Figure 1-19 Metal Cover In Unused Slot P1

    Installing the System Installing Additional Components If the system is powered off, install the hot-swappable power supply into the server before CAUTION attaching the new power cord at the rear of the system. Failure to observe this caution results in damage to the server. To install a hot-swappable power supply, follow these steps: Step 1.

  • Page 42: Figure 1-20. Volume Filler Installation In Slot 2

    Installing the System Installing Additional Components Installing Hot-Pluggable Disk Drives One additional hot-pluggable disk drive can be added to the server in slot 2. Always use low profile disk drives (1 inch height) in the server. To install a hot-pluggable disk drive, follow these steps: Step 1.

  • Page 43: Installing Processors

    Installing the System Installing Additional Components Figure 1-21 Disk Drive Installation in Slot 2 Step 3. Close the drive ejector handle by pushing it down until it clicks. The hot-pluggable disk drive is now correctly installed. Figure 1-22 Disk Drive Installation in Slots 1 and 2 Slot 2—SCSI ID 1 Slot 1—SCSI ID 0 Installing Processors...
  • Page 44 If you are installing fewer than the maximum number of dual processor modules (one in the rp4410 server or fewer than four in the rp4440 server), they must be installed in the designated locations on the processor extender board.

  • Page 45: Table 1-7 Dual Processor Module Load Order

    Installing the System Installing Additional Components Table 1-7 lists the load sequence. Table 1-7 Dual Processor Module Load Order Dual Processor Server Connector Module rp4410 or CPU0 rp4440 rp4410 or CPU1 rp4440 rp4440 only CPU2 rp4440 only CPU3 Removing the Processor Extender Board...

  • Page 46: Figure 1-23 Extender Board Latches

    Installing the System Installing Additional Components Figure 1-23 Extender Board Latches Step 5. Pull out on the extraction levers to unplug the processor extender board from the socket located on the midplane riser board. Step 6. Pull out the processor extender board from the chassis. Chapter 1...

  • Page 47: Figure 1-24 Removing The Processor Extender Board

    Installing the System Installing Additional Components Figure 1-24 Removing the Processor Extender Board CPU1 CPU0 CPU3 (under) CPU2 (under) Installing a Processor on the Extender Board CAUTION Observe all ESD safety precautions before attempting this procedure. Failure to follow ESD safety precautions can result in damage to the server.

  • Page 48: Figure 1-25 Processor Cable Placed Correctly

    Installing the System Installing Additional Components Step 5. Carefully lower the processor, without the sequencer frame, onto the processor socket. Align the pins on the bottom of the heatsink to the slots in the retention frame on the extender board. CAUTION Do not press the processor modules into the socket.

  • Page 49: Figure 1-26 Processor Cable Placed Incorrectly

    Installing the System Installing Additional Components Figure 1-26 Processor Cable Placed Incorrectly Heatsink Cable Placed Incorrectly - Pinched Between Heatsink and Extender Board Frame Protective Plastic Sleeve Sheet Metal Frame Step 6. Lock the assembly to the socket by rotating the cam on the socket 180 degrees clockwise using the CPU Install Tool or 2.5-mm Allen wrench.

  • Page 50: Figure 1-27. Installing The Processor On The Extender Board

    Installing the System Installing Additional Components Figure 1-27 Installing the Processor on the Extender Board Tightening Sequence for 4-Shoulder Screws is 1, 2, 3, 4 DO NOT OVERTIGHTEN (See Step 7) 2 Knurled Thumb- Torx-T15 Screws Use Torx T15 Driver to Tighten Shoulder Screws and Thumbscrews...

  • Page 51: Installing Memory

    Use MAKODIAG provided by the offline diagnostic environment to exercise the processor. Installing Memory The standard configuration of HP 9000 rp4410 and rp4440 servers include a 16-DIMM memory extender board. This extender board must contain a minimum of 1 GB of memory (four 256 MB DIMMs loaded in quad 0 [connectors 0A, 0B, 0C, and 0D]).

  • Page 52: Table 1-8 Dimm Filler Requirements For 16 Dimm Extender Board

    Installing the System Installing Additional Components Table 1-8 and Figure 1-28 show the DIMM filler requirements and configuration for the 16-DIMM memory extender board. Table 1-8 DIMM Filler Requirements for 16 DIMM Extender Board DIMMs Loaded Fillers Required 4 DIMMs in quad 0 Six fillers total: Two fillers each in quads 1, 2, and 3 8 DIMMs in quads 0 and 1...
  • Page 53 Installing the System Installing Additional Components Table 1-9 DIMM Filler Requirements for 32-DIMM Memory Extender Board 4 DIMMs in quad 0 12 fillers total: Two fillers in quads 1, 3, 4, 5, 6, and 7 (quad 2 remains unfilled) 8 DIMMs in quads 0 and 1 Eight fillers total: Two fillers in quads 4, 5, 6, and7 (quads 2 and 3 remain unfilled)

  • Page 54: Figure 1-29 32-Dimm Memory Extender Board Minimum Configuration

    Installing the System Installing Additional Components Figure 1-29 32-DIMM Memory Extender Board Minimum Configuration DIMM Filler Chapter 1...

  • Page 55: Figure 1-30 Removing The Memory Extender Board

    Installing the System Installing Additional Components Removing a Memory Extender Board The memory extender boards is located under the front cover. Ensure that the system is powered off and all power sources have been disconnected WARNING from the server prior to attempting this procedure. Voltages are present at various locations within the server whenever an ac power source is connected.

  • Page 56: Figure 1-31 Inserting Dimm Into The Extender Board Connector

    Installing the System Installing Additional Components Installing DIMMs To install DIMMs, follow these steps: Step 1. Align the DIMM with the socket located on the memory extender board. (Align the notch in the DIMM with the tab in the connector.) Step 2.

  • Page 57: Hot-Pluggable Pci/Pci-X

    Installing Additional Components Step 6. Replace the front bezel onto the chassis. (See “Replacing the Front Bezel” on page 29.) Hot-Pluggable PCI/PCI-X The HP 9000 rp4410 and rp4440 servers support PCI/PCI-X hot-pluggable technology and includes six hot-pluggable PCI/PCI-X slots. Hot-Pluggable PCI/PCI-X Operations PCI/PCI-X hot-pluggable technology enables the following operations.

  • Page 58: Figure 1-32. Slot Id Numbering

    Installing the System Installing Additional Components PCI/PCI-X Slot Locations and Configurations PCI/PCI-X slots are numbered from 1 through 8 in the server as shown in Figure 1-32. Figure 1-32 Slot ID Numbering PCI-X Bus 1 PCI-X Bus 2 PCI-X Bus 3 PCI-X Bus 4 PCI-X Bus 5 PCI Slot ID Numbers...

  • Page 59: Table 1-11. Pci/Pci-X Card Slot Frequency And Bus Mode Compatibility For Shared Slots

    Installing the System Installing Additional Components Shared slots have card compatibility restrictions. If one of the shared slots is occupied, the card being added to the second slot is limited by the configuration of the occupied slot. If the new card has a slower capability than the current bus configuration, it cannot work.
  • Page 60 Installing the System Installing Additional Components Hot-Plug Procedures The hot-plug procedures described in this section use the hardware interface only. Software interface procedures are described in Table 1-10 on page 57. IMPORTANT Before adding or replacing a PCI/PCI-X card, determine whether that card is critical to the server operation.

  • Page 61: Figure 1-33 Pci/Pci-X Olx Divider Layout

    Installing the System Installing Additional Components Figure 1-33 PCI/PCI-X OLX Divider Layout PCI-X Card Latch Closed Position PCI-X Card Latch Open Position MRL—Closed MRL—Open Power LED Light Pipe Attention Button Attention LED Light Pipe Step 4. Ensure that the MRL and the card latch on the OLX divider are already open and insert the PCI/PCI-X card into the empty slot.

  • Page 62: Figure 1-34 Inserting Pci/Pci-X Card

    Installing the System Installing Additional Components Figure 1-34 Inserting PCI/PCI-X Card Step 5. If the PCI/PCI-X card is full size, open the slider gate latch to access the card slot. Chapter 1...

  • Page 63: Figure 1-35 Slider Gate Latch

    Installing the System Installing Additional Components Figure 1-35 Slider Gate Latch Step 6. If the PCI/PCI-X card is full size, close the slider gate latch to secure the end of the card. (Figure 1-35) Step 7. Push the MRL down until it seats against the chassis wall. Chapter 1...
  • Page 64 Installing the System Installing Additional Components Step 8. Turn the PCI/PCI-X card latch to the closed position to capture the PCI/PCI-X card and MRL into the closed position. Step 9. Press the button . The power LED starts to blink. Wait until the power LED goes from Attention blinking to steady on.

  • Page 65: Table 1-12. Hot-Pluggable Led Descriptions

    Installing the System Installing Additional Components IMPORTANT When inserting the PCI/PCI-X card, be careful you do not accidentally touch an button on the other OLX dividers. This initiates an undesired shutdown of Attention another PCI/PCI-X card/slot. If you accidentally initiate slot shutdown, push the button again within five seconds to cancel the shutdown.

  • Page 66: Converting Scsi From Simplex To Duplex

    Converting SCSI From Simplex to Duplex This section explains how to convert the HP 9000 rp4410 or rp4440 server from simplex to duplex operation. The process involves removing a jumper, installing a duplex PCA card, and plugging in the stowed channel B cable to the appropriate sockets.
  • Page 67 Installing the System Installing Additional Components Ensure that the system is powered off and all power sources have been WARNING disconnected from the server prior to attempting this procedure. NOTE Some restrictions apply to the mass storage devices that can be connected to the core I/O SCSI HBA.

  • Page 68: Figure 1-36 Removing The Scsi Jumper Cable

    Installing the System Installing Additional Components Figure 1-36 Removing the SCSI Jumper Cable Step 2. Install the duplex board in the SCSI connector located nearest the disk drive cage. a. Align the bracket tabs with the slots on the side of the disk drive cage. b.

  • Page 69: Figure 1-37 Installing The Duplex Board

    Installing the System Installing Additional Components Figure 1-37 Installing the Duplex Board Step 3. Secure the duplex board to the disk drive cage by the bracket and to the SCSI backplane by the SCSI connector sockets. (Figure 1-37) Step 4. Install the SCSI Cable B on the SCSI backplane. (Figure 1-38) a.

  • Page 70: Figure 1-38 Installing Scsi Cable B To The Scsi Backplane

    Installing the System Installing Additional Components Figure 1-38 Installing SCSI Cable B to the SCSI Backplane Step 5. Connect the other end of the SCSI Cable B to the SCSI B channel connector on the SCSI adapter board. (Figure 1-39) a.

  • Page 71: Figure 1-39 Installing Scsi Cable B To The Scsi Adapter Board

    Installing the System Installing Additional Components Figure 1-39 Installing SCSI Cable B to the SCSI Adapter Board Replacing the Removed Modules To return the server to operational configuration, follow these steps: Step 1. Replace the processor extender board. (See “Replacing the Processor Extender Board” on page 51.) Step 2.

  • Page 72: Installing The Server Into A Rack, Non-Hp Rack, Or Pedestal

    Installing the System Installing the Server Into a Rack, Non-HP rack, or Pedestal Installing the Server Into a Rack, Non-HP rack, or Pedestal The following information describes how to install the server into an HP rack. Information is also provided on approved non-HP rack and pedestal mount alternatives.

  • Page 73: Connecting The Cables

    AC Input Power The HP 9000 rp4410 and rp4440 servers come with one or two power supplies installed. A power supply includes an ac input connector which is rated for 200 to 240 VAC at 13 amps. If two power supplies are installed, both power supplies must be connected separately to an ac power source.

  • Page 74: Applying Standby Power To The Server

    Gigabit Ethernet LAN Port Local Aux Remote Console/Remote/UPS Port (RS-232) iLO MP LAN Port (10/100 LAN Cable (M Cable & RS-232 DB-9F to DB-9F) USB Ports VGA Port The VGA port is disabled on the rp4410 and rp4440 servers. Chapter 1...

  • Page 75: Console Setup

    Installing the System Console Setup To enable general network connectivity for the server, follow these steps: Step 1. Obtain a valid IP address for each LAN port you plan to activate. Step 2. Connect the LAN cable from an available LAN port into a live connection on the network. Console Setup This section describes how to set up and start a console session on the server.

  • Page 76: Setup Checklist

    Installing the System Console Setup Setup Checklist Use the checklist in Table 1-13 to assist with the iLO MP setup process. Table 1-13 Setup Checklist Step Action Standard Setup Preparation 1. Determine a LAN configuration method and assign an IP address if necessary. 2.

  • Page 77: Setup Flowchart

    Installing the System Console Setup Setup Flowchart Use this flowchart as a guide to assist in the Integrity iLO MP setup process. Figure 1-41 iLO MP Setup Flowchart and IP address and IP address Chapter 1...

  • Page 78: Preparation

    Installing the System Console Setup Preparation You must perform the following tasks before you can configure the iLO MP LAN. • Determine the physical access method to select and connect cables. • Determine the iLO MP LAN configuration method and assign an IP address if necessary. Determining the Physical iLO MP Access Method Before you can access the iLO MP, you must first determine the correct physical connection method.

  • Page 79: Configuring The Ilo Mp Lan Using Dhcp And Dns

    Installing the System Console Setup Table 1-15 LAN Configuration Methods (Continued) RS-232 Serial Port DHCP LAN Configuration Method (iLO MP LC command) ARP Ping ARP Ping, RS-232 serial port, or remote/modem port RS-232 serial port, or remote/modem port RS-232 serial port, remote/modem port, or ARP Ping Cannot set up the LAN.

  • Page 80: Table 1-16 Arp Ping Commands

    Installing the System Console Setup ARP Ping operational issues include the following: • You can use ARP Ping regardless of the status of DHCP, unless an IP address has ever been acquired using DHCP. • When ARP Ping is successful, DHCP status is disabled. •...

  • Page 81: Configuring The Ilo Mp Lan Using The Rs-232 Serial Port

    Installing the System Console Setup For example: arp -s 192.0.2.1 00-00-0c-07-ac-00 Step 6. At the DOS prompt, enter ping followed by the IP address to verify that the iLO MP LAN port is configured with the appropriate IP address. The destination address is the IP address that is mapped to the iLO MAC address.

  • Page 82: Logging In To The Ilo Mp

    Installing the System Console Setup IMPORTANT Do not use hpterm and vt100 terminal types at the same time. There are many different emulation software applications. Consult the help section of your emulation software application for instructions on how to configure the software options. Step 3.

  • Page 83: Additional Setup

    Installing the System Console Setup Following is the screen: MP Main Menu MP MAIN MENU: CO: Console VFP: Virtual Front Panel CM: Command Menu CL: Console Logs SL: Show Event Logs HE: Main Menu Help X: Exit Connection This example shows the accessed through the local serial port.

  • Page 84: Accessing The Host Console

    Installing the System Accessing the Host Console b. Enter CM at the MP> prompt. Enter UC at the MP:CM> prompt and follow the prompts to modify user accounts. Setting Up Security For greater security and reliability, HP recommends that iLO MP management traffic be on a separate dedicated management network and that only administrators be granted access to that network.

  • Page 85: Interacting With The Ilo Mp Using The Web Gui

    Installing the System Accessing the Host Console Interacting with the iLO MP Using the Web GUI Web browser access is an embedded feature of the iLO MP. The iLO MP has a separate LAN port from the system LAN port. It requires a separate LAN drop, IP address, and networking information from that of the port used by the operating system.

  • Page 86: Powering On And Powering Off

    Installing the System Powering ON and Powering OFF Figure 1-43 Status Summary Page Function Tabs Navigation Bar Display Screen Step 4. Select the Web interface functions by clicking the tabs at the top of the page. Each function Function lists options in the on the left side of the page.

  • Page 87: Powering On The Server

    Installing the System Powering ON and Powering OFF Table 1-17 lists the server power states. Table 1-17 Power States Power Activated through the Power Cable Standby dc iLO MP PC Command; or dc Voltage Power States Plugged Into Voltage Front Panel Power Button Applied? Receptacle? Applied?

  • Page 88: Powering Off The Server

    Installing the System Powering ON and Powering OFF Step 2. Press the power button to start the server. Step 3. Start the operating system. Powering Off the Server Power off the server using the following methods if the server is in the standby or full power state: •...

  • Page 89: Booting The Operating System

    This section covers procedures for booting and shutting down an operating system on the server. Supported Operating System The only supported operating system on the HP 9000 rp4410 and rp4440 servers is HP-UX 11i Version 1 (and higher HP-UX versions that support PA-RISC systems.) Booting and Shutting Down HP-UX This section describes booting and shutting down HP-UX on the HP 9000 rp4410 and rp4440 servers.

  • Page 90: Verifying The Server Configuration Using Boot Console Handler

    Installing the System Booting the Operating System Step 1. At the BCH , enter command or menu> bo pri. The following message displays: Main Menu Interact with IPL (Y, N, or Cancel)?> Step 2. To interact with IPL, answer y. Step 3.

  • Page 91: Troubleshooting

    Installing the System Troubleshooting • me (Memory) • io (Check the PCI device information to determine if the values match the devices installed in the server) Step 2. Verify the parameters. Step 3. To return to the BCH , use the ma command . Main Menu Troubleshooting This section provides basic server troubleshooting information.

  • Page 92: Server Does Not Power On

    Installing the System Troubleshooting Table 1-18 describes what happens when the server is at BCH, and you press the power button. Table 1-18 Server Power Button Functions When Server is On and at BCH Action Reaction One to three seconds System power turns off immediately (hard power off) Five seconds or longer System power turns off immediately (hard power off)

  • Page 93: Bch Menu Is Not Available

    Installing the System Troubleshooting • If the console shows that the server is powered on, but server LEDs indicate that power is off, remove and reseat connectors on the LED status board. If the problem persists, replace the LED status board. If the console shows that the server is not powered on (server is off), remove and reseat connectors on the system board.

  • Page 94: Dvd Problems

    Installing the System Troubleshooting DVD Problems DVD problems that occur during installation are usually related to faulty connections. If you are experiencing DVD problems, follow these steps: 1. Remove and reinsert the disk. 2. Replace the disk. 3. Remove and reinstall the DVD drive. Check that connectors are fully engaged. 4.

  • Page 95: Troubleshooting Using Led Indicators

    Installing the System Troubleshooting Step 6. Select the firmware package you want to download. Step 7. Download the firmware package, and follow the instructions for updating the firmware included in the release notes. Installing the Latest Version of the Firmware on the Server To install the latest version of the firmware on the server, follow these steps: Step 1.
  • Page 96 Installing the System Troubleshooting Table 1-21 Front Control Panel LED Definitions (Continued) LED/ State Flash Rate Color Description Button System LED Attention Flashing at 1 Hz Yellow Warning—System needs attention. Redundancy lost, component failure pending. (Additional information can be found in the System Log).

  • Page 97: Table 1-22. Quickfind Diagnostic Panel Led Definitions

    Installing the System Troubleshooting Table 1-22 QuickFind Diagnostic Panel LED Definitions (Continued) Item LED 0 LED1 LED2 LED3 Details Memory DIMM xA DIMM xB DIMM xC DIMM xD The specified DIMM has failed—reseat or bank X (0-7) replace the memory board and DIMM. If all the LEDs for a rank (0-7) are lit and the memory config error LED is lit, then the DIMMs in the specified rank are...
  • Page 98 Installing the System Troubleshooting Figure 1-45 QuickFind Diagnostic Label Processor Subsystem I/O VRM CPU VRM Memory 0 Memory 1 Memory 2 Memory 3 Memory 4 Memory 5 Memory 6 Memory 7 Power Supply Memory Config Error Processor Config Error Missing Component System Temperature Check Event Log Chapter 1...

  • Page 99: Information To Collect Before You Contact Support

    Installing the System Troubleshooting Information to Collect Before You Contact Support Before you contact HP support, you should: Step 1. Check information on troubleshooting and attempt to solve the problem. • Note failure symptoms and error indications (LEDs and messages) by checking the system event log.
  • Page 100 Installing the System Troubleshooting Chapter 1...

  • Page 101: Index

    Index ac input power emulation device, configuring ARP Ping external core I/O features attention button (doorbell) fans hot-swappable, remove and replace front cover remove and replace backplane SCSI accessing front panel controls and indicators battery system, remove and replace booting HP-UX hard disk drive LVM maintenance mode...
  • Page 102 Index power button full state network connectivity off state LEDs PR command hot-pluggable disk drives problems logging in to the iLO MP reset command See PR standby state states MAC address supplies, installing label powering off the server management processor See iLO MP manually memory using the iLO MP PC command...
  • Page 103 Index troubleshooting methodology operating system unloading the server unpacking, inspecting for damage user accounts modifying validate server configuration verify site preparation iLO MP login page iLO MP status summary page iLO MP, launch help interacting with GUI...

This manual is also suitable for:

Rp44409000 rp4410-49000 rp4440-89000 rp44109000 rp4440

Table of Contents