Table of Contents
Advertisement
Parameter/
Explanation
Range
TOTAL
NS Threshold (Noise Suppressor Threshold)
This controls the global threshold level for the noise
suppressor settings in each patch. This feature is effec-
tive when you connect a different bass or for adjusting
for changes in noise levels in the performance venue.
-20–+20dB
It does not affect the settings in each individual patch.
To use the settings contained in the individual patches, set
this to 0 dB.
Rev Level (Reverb Level)
This controls the global reverb level for the reverb
settings in each patch. Adjusting this reverb level is
effective for adjusting to the acoustics of the perfor-
mance space. It does not affect the settings in each
0–200%
individual patch.
To use the settings contained in the individual patches, set
this to 100%.
USB/DGT Out Lev (USB/Digital Out Level)
Adjusts the volume level of the digital audio signals
0–200%
output to the USB (Computer).
USB Mix Level
Sets the volume level of the mixed digital
0–200%
audio signals from USB (Computer) when Input Se-
lect is set to "Bass 1–3."
Main Out Level
This sets the output reference level to match the equipment connect-
ed to the OUTPUT jack.
-10dB
Choose this when connected to a bass amp.
Choose this when connected to a recorder, mixer, or
+4dB
other line device.
SUB OUTPUT
Mode
This sets the signals to be output from the SUB OUTPUT (XLR)
jacks.
The GT-10B's stereo output is output as is, without
L/R
change. Set to L/R when recording in stereo or
sending stereo signals to a PA.
Output from SUB OUTPUT L jack is the GT-10B's
stereo output mixed to mono, output from SUB
OUTPUT R jack is the sound before effect (mono)
directly.
Effect/
The INPUT SELECT, INPUT LEVEL and PRES.
Direct
parameters are enabled in the input sound.
For recording, you can record the direct bass sound on a
separate channel, then later on you can remix the direct
sound with the effect sound during mixdown.
Level
Adjusts the level of the audio signals output from
the SUB OUTPUT (XLR) jacks.
0–100
The SUB OUTPUT level cannot be adjusted with the
OUTPUT LEVEL knob
Chapter 8 Parameters Guide
PHRASE LOOP
Parameter/
Explanation
Range
PHRASE LOOP
Off, On
Switches the Phrase Loop function on/off.
Mode
This records the sound after it passes through
the effects.
Performance
This lets you achieve a rich variety of perfor-
mances by combining different tones.
This records the sound before it passes through
the effects, and applies the effects during loop
Patch Edit
play.
This enables you to adjust effects or compare
patch tones.
Pdl Mode (Pedal Mode)
The BANK pedals are not used for operation of
the Phrase Loop feature. These are used as bank
switch pedals.
Off
Phrase Loop can be controlled by assigning the
Phrase Loop feature to any of the CTL 1 through 4
etc. and maintaining the BANK pedals' bank
switching function.
The BANK pedals are used for operation of the
On
Phrase Loop feature.
Rec Mode (Recording Mode)
Mono
Phrases are recorded in mono.
Stereo
Phrases are recorded in stereo.
Play Lev (Play Level)
0–120
Sets the phrase playback volume.
Clear Pdl (Clear Pedal Function)
When you press [BANK ▲] while the Phrase
Clear Only
Loop feature is on, the recorded data is cleared
and then GT-10B switches to STANDBY mode.
When you press [BANK ▲] while the Phrase
Loop feature is on, the performance of the re-
corded phrase is muted (the recorded data is
not erased).
If you then press [BANK ▲] again while the
phrase is muted, the recorded data is cleared
Mute/Clear
and then GT-10B switches to STANDBY mode.
Skillful use of muting lets you combine your own
performances with prerecorded phrases at the timing
you want.
135
Advertisement
Table of Contents
