Advertisement
Quick Links
PRODUCT DETAILS:
Part Number:
ECU Number:
Tail Harness Length Required:
TBM/Lug Part Number:
Wiring Part Number:
FITTING DETAILS:
Towbar Installation Time:
Wiring Installation Time:
Total Installation Time:
Note:
•
Please refer vehicles owner's manual for proper operation
and understanding of towing features enabled when coded.
CENTRE RECOVERY HOOK
CENTRE RECOVERY POINT LOADING MUST NOT EXCEED 8000kg.
DESIGNED FOR USE WITH A SNATCH STRAP NOT
EXCEEDING 8000kg MBS (MINIMUM BRAKING STRENGTH).
SIDE RECOVERY HOOK (SINGLE)
SIDE RECOVERY POINT LOADING MUST NOT EXCEED 4000kg MBS
(MINIMUM BRAKING STRENGTH).
Hayman Reese (Cequent)
PO Box 4050, Dandenong South VIC 3164
Phone 1800 812 017 Email info@haymanreese.com.au
Rev:
A
03429XW
Maximum Towing Braked:
WLE70029
Maximum Towing Unbraked:
1200 mm
Maximum Static Ball Load:
21366
WLL90029
70 Mins.
Hayman Reese SmartCODE Solution Required:
30 Mins.
RPA Disable/Other:
Bumper Cut Required:
100 Mins.
Page
INSTALLATION INSTRUCTIONS
PART NUMBER
FORD RANGER MY22 UTE X-BAR
1
TOWBAR
03429XW
3500
kg
750
kg
350
kg
YES
YES
No
Issue Date:
31-08-2022
Advertisement
Related Manuals for Hayman Reese 03429XW
Summary of Contents for Hayman Reese 03429XW
- Page 1 Maximum Static Ball Load: TBM/Lug Part Number: 21366 Wiring Part Number: WLL90029 FITTING DETAILS: Towbar Installation Time: 70 Mins. Hayman Reese SmartCODE Solution Required: Wiring Installation Time: 30 Mins. RPA Disable/Other: Bumper Cut Required: Total Installation Time: 100 Mins. Note: •...
- Page 2 1. 2. Do not, drill, cut, weld or otherwise modify the towbar. FOR TOWING PURPOSES ONLY - This towbar is designed and tested by Hayman Reese to adhere to ADR 62/02 which provides only for the expected load demands of towing.
- Page 3 TOWBAR INSTALLATION INSTRUCTIONS PART NUMBER 03429XW FORD RANGER MY22 UTE X-BAR TOWBAR ASSEMBLY DIAGRAM Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: Page Issue Date: 31-08-2022...
- Page 4 XBAR COVER SPRING 60Lx10ODx1P COMPLIANCE LABEL LOAD RATING LABEL X-BAR DECAL STICKER MKII CAN MODULE WARNING LABEL WIRING LOOM Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: Page Issue Date: 31-08-2022...
- Page 5 SPACER PLATE WASHER TORQUE FASTENERS 4 x M12 x 45mm BOLT TO 100 N.m WASHER B. MOUNT PLUGS TO BRACKET Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: Page Issue Date: 31-08-2022...
- Page 6 TO PREVENT DAMAGE TO BUSHES WITH SCREW HOLES III. FINALLY FASTEN COVER TO HOUSING BY PUSHING Hayman Reese (Cequent) SCREWS THROUGH BUSHES AND SECURING WITH NUTS PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev:...
- Page 7 3. From under the chassis, remove and discard the rear step support bracket secured with 2x M14 bolts per side. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev:...
- Page 8 Torque side arms to crosstube first in an even pattern/sequence. Repeat for side arms to chassis rail and finally torque all other fasteners. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev:...
- Page 9 13. Mount the trailer plug to plug bracket, route the tail blue connector towards trailer patch mating connector. 14. Connect and waterproof the blue connector using electrical grease or silicon. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: Page...
- Page 10 Note: Care must be taken when moving the module. 18. Using a flat blade screwdriver release the connector tabs for the 3x trailer pre-wire connectors. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: Page...
- Page 11 21. Connect the trailer patch connector to the ECU (WLE70029). 22. Remove the ECU adhesive backing tape and secure the module in behind the LHS footwell. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev:...
- Page 12 27. Once vehicle is coded, test trailer functionality with a test board. Place fitting instructions in glovebox when finished. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: Page Issue Date:...
- Page 13 TOWBAR MAINTENANCE AND CARE: 1. Hayman Reese recommend that the towbar LUG or TBM (tow ball Mount) Pull Pin and R-clip are removed and stored when not in use. Removal of LUG or TBM (tow ball mount) is advisable when not in use to assist with any of the following.
- Page 14 VEHICLE’S GLOVEBOX AFTER INSTALLATION HAYMAN REESE SMART PIN Your Hayman Reese towbar is equipped with Smart Pin technology to help reduce towbar tongue rattle in most driving conditions. Please ensure below instructions are understood and routine maintenance is carried out to ensure best towing experience.
- Page 15 OE functionality as set by OE manufacturer. Please read the vehicles owner’s manual for proper operation and understanding. Coding can be carried out using the Hayman Reese SmartCODE (HRSC) using the following steps. Note, if HRSC is unavailable, vehicle coding can be carried out by OE manufacturer as needed.
Need help?
Do you have a question about the 03429XW and is the answer not in the manual?
Questions and answers