Setting Up The System - Denon AVR-5800 Operating Instructions Manual

7 SETTING UP THE SYSTEM

• Once all connections with other AV components have been completed as described in "CONNECTIONS" (see pages 6 to 13), make the
various settings described below on the monitor screen using the AVR-5800's on-screen display function.
These settings are required to set up the listening room's AV system centered around the AVR-5800.
• Use the following buttons to set up the system:
Screen while icons are displayed
• System setup items and default values (set upon shipment from the factory)
Input the combination of speakers in your system and their
Speaker corresponding sizes (SMALL for regular speakers, LARGE for full-
Configuration size, full-range) to automatically set the composition of the signals
output from the speakers and the frequency response.
Use this function when using multiple surround speaker
q
combinations for more ideal surround sound. Once the
(Surround
combinations of surround speakers to be used for the
Speaker
different surround modes are preset, the surround
Setting)
speakers are selected automatically according to the
surround mode.
Subwoofer mode This selects the subwoofer speaker for playing deep bass signals.
SB CH Auto Set the method of playing the surround back channel for digital
w
Flag Detect signals.
This parameter is for optimizing the timing with which the audio
e
Delay Time signals are produced from the speakers and subwoofer according to
the listening position.
Multi Zone-1
vol. Level
Multi Zone
r
Control
Power AMP
Assignment
This adjusts the volume of the signals output from the speakers and
Channel
t
subwoofer for the different channels in order to obtain optimum
Level
effects.
This parameter is for detecting the maximum level of the low bass
Subwoofer
signals output from the subwoofer channel in order to protect the
y
Peak Limit
subwoofer from damage and prevent unpleasant distorted sounds
Lev
from being produced.
Digital In This assigns the digital input jacks for the different input
u
Assignment sources.
This sets whether or not to display the on-screen display that
On Screen appears on the monitor screen when the controls on the remote
i
Display control unit or main unit are operated (from MONITOR 1 outputs
only).
Auto Tuner
o
FM stations are received automatically and stored in the memory.
Presets
16
System setup
This sets the output level for the multi-zone 1
output jacks.
Set this to switch the surround back channel's
power amplifier for use for multi-zone 2.
Front Sp. Center Sp.
Small Small
DOLBY/
Surround
THX
DTS
mode SURROUND
SURROUND
Surround
A A
speaker
Front L & R Center
12 ft (3.6 m) 12 ft (3.6 m)
Front R Center
Front L
0 dB 0 dB 0 dB
Input
CD DVD VDP
source
Digital COAXIAL COAXIAL COAXIAL OPTICAL
Inputs 1 2 3
A1 ~ A8 87.5/89.1/98.1/107.9/90.1/90.1/90.1/90.1 MHz
B1 ~B8 520/600/1000/1400/1500/1710 kHz/90.1/90.1 MHz
C1 ~C8 90.1 MHz
D1 ~D8 90.1 MHz
E1 ~E8 90.1 MHz
Transmission codes
of independent buttons
CHANNEL• : Tuner preset
CHANNELª : Tuner preset
VOL• : Main volume of AV amplifier
VOLª : Main volume of AV amplifier
MUTE : Muting of AV amplifier
Default settings
Surround Sp. Surround Back Sp.
Small Small / 2spkrs
WIDE 5CH/7CH DSP
EXT. IN-1
SCREEN STEREO SIMULATION
A A A A
LFE —THX—
Auto Flag Detect Mode = OFF
Surround L & R SBL & SBR
10 ft (3.0 m) 10 ft (3.0 m)
Variable
Surround Back
Surround Surround Surround
L R Back L
0 dB 0 dB 0 dB
Peak Limitter = OFF
TV DBS/SAT VCR-1 VCR-2 VCR-3
OPTICAL OPTICAL
OPTICAL
OFF
1 2 3 4
On Screen Display = ON
Sub Woofer
Yes
—
EXT. IN-2
A —
Sub Woofer
12 ft (3.6 m)
Surround
Subwoofer
Back R
0 dB 0 dB
TAPE-1 TAPE-2 V. AUX
OPTICAL OPTICAL
OFF
5 6