The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 2 / 18 Index <Notice>.................. 3 Preparations before starting the operation ..........4 Preparation for the Personal Computer ..........4 Preparations for the cables ............4 Connection of AV receiver/amplifier and PC ..........5 Connection diagram ..............
Page 3 / 18 Notice> < After upgraded, the setting of product (AVR-5805CI) is initialized, so please set all the settings again according to the manual (attached to the product at the time of purchase). Please keep the following notice for firmware update.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 4 / 18 1. Preparations before starting the operation 1.1 Preparation for the Personal Computer Minimum hardware and software requirements: Type PC/AT compatible Intel Pentium/Celeron500MHz or faster 128MB or more...
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 5 / 18 2. Connection of AV receiver/amplifier and PC 2.1 Connection diagram You can select the following 3 methods. Also connect the display monitor for OSD. a) Connect the Ethernet cross cable between Ethernet port of PC and Ethernet port of AV Receiver/Amplifier.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 6 / 18 3. Firmwares update procedure. In case of direct connection without hub using cross cable (refer to 2.1.a) 3.1 Setup the IP address of the PC (refer to 6) Setup the IP Address.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 7 / 18 3.4 Connect the AV Receiver/Amplifier and the PC 1) Connect the AV Receiver / Amplifier and the PC (refer to 2.1.a). 2) Push [OK] button on the dialog.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 8 / 18 controller. Confirm that “Subnet Mask” is highlighted. Push the [CH SELECT ENTER] button of the AV Receiver / Amplifier or the remote controller 3 times slowly. You can exit from the System Setup menu.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 9 / 18 3.8 Start the firmware update. Click the “Update” button. You can see the following indication. This upgrade takes almost 5 minutes from beginning to the end. The upgrade situation is displayed as the bar graph, and can confirm the status.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 10 / 18 4. Firmwares update procedure. In case of Ethernet HUB or Router (without DHCP server ability) (refer to 2.1.b) 4.1 Setup the IP address of the PC (refer to 6) Setup the IP Address.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 11 / 18 4.4 Connect the AV Receiver/Amplifier and the PC 1) Connect the AV Receiver / Amplifier and the PC (refer to 2.1.b). 2) Push [OK] button on the dialog.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 12 / 18 controller. Confirm that “Subnet Mask” is highlighted. Push the [CH SELECT ENTER] button of the AV Receiver / Amplifier or the remote controller 3 times slowly. You can exit from the System Setup menu.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 13 / 18 4.8 Start the firmware update. Click the “Update” button. You can see the following indication. This upgrade takes almost 5 minutes from beginning to the end. The upgrade situation is displayed as the bar graph, and can confirm the status.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 14 / 18 5. Firmwares update procedure. In case of Ethernet HUB or Router (with DHCP server ability) (refer to 2.1.c) 5.1 Run the upgrade application Run the AVR-5805CI_UTOOL_23_0_0_1.exe. 5.2 Confirmation of notes...
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 15 / 18 5.3 Connect the AV Receiver/Amplifier and the PC 1) Connect the AV Receiver / Amplifier and the PC (refer to 2.1.c). 2) Push [OK] button on the dialog.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 16 / 18 5.6 Communication check 1) Push the [Check communication] button. (1) 2) If connection is good, then you can see the “Communication check OK.” message, and push the [OK] button.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 17 / 18 5.7 Start the firmware update. Click the “Update” button. You can see the following indication. This upgrade takes almost 5 minutes from beginning to the end. The upgrade situation is displayed as the bar graph, and can confirm the status.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 18 / 18 6. Setup the IP address of the PC. Click [Start] on the taskbar of Windows, and open the Explorer. Click [Control panel]. Click [Network Connections]. Double-click [Local Area Connections].
Need help?
Do you have a question about the AVR-5805CI and is the answer not in the manual?
Questions and answers